相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Effects of tensile test parameters on the mechanical properties of a bimodal Al-Mg alloy
Andrew Magee et al.
ACTA MATERIALIA (2012)
Micromechanical behavior study of forged 7050 aluminum alloy by microindentation
Jiang Li et al.
MATERIALS & DESIGN (2012)
Complete mechanical characterization of nanocrystalline Al-Mg alloy using nanoindentation
Evan Harvey et al.
MECHANICS OF MATERIALS (2012)
The effect of holding time on nanoindentation measurements of creep in bone
Ziheng Wu et al.
JOURNAL OF BIOMECHANICS (2011)
Nanoindentation strain-rate jump tests for determining the local strain-rate sensitivity in nanocrystalline Ni and ultrafine-grained Al
Verena Maier et al.
JOURNAL OF MATERIALS RESEARCH (2011)
Mathematical Analysis on the Uniqueness of Reverse Algorithm for Measuring Elastic-plastic Properties by Sharp Indentation
Yongli Huang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2011)
Loading rate dependency of maximum nanoindentation depth in nano-grained NiTi shape memory alloy
Abbas Amini et al.
MATERIALS LETTERS (2011)
Direct observation of amophization in load rate dependent nanoindentation studies of crystalline Si
C. R. Das et al.
APPLIED PHYSICS LETTERS (2010)
Effect of grain size on strain rate sensitivity of cryomilled Al-Mg alloy
Byungmin Ahn et al.
JOURNAL OF MATERIALS SCIENCE (2010)
Novel ultra nanoindentation method with extremely low thermal drift: Principle and experimental results
J. Nohava et al.
JOURNAL OF MATERIALS RESEARCH (2009)
Effect of loading rate on the serrated flow of a bulk metallic glass during nanoindentation
T. Burgess et al.
ACTA MATERIALIA (2008)
Microstructure and nano-scale mechanical behavior of Mg-Al and Mg-Al-Ca alloys
Lihong Han et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
A critical appraisal of the extraction of creep parameters from nanoindentation data obtained at room temperature
R. Goodall et al.
ACTA MATERIALIA (2006)
Indentation size effects in the nano- and micro-hardness of fcc single crystal metals
Z. Zong et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Modeling the constitutive response of bimodal metals
S. P. Joshi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2006)
Size effects in micro- and nanoscale indentation
Eze Manika et al.
ACTA MATERIALIA (2006)
Measuring the plastic properties of bulk materials by single indentation test
N Ogasawara et al.
SCRIPTA MATERIALIA (2006)
Indentation size effect in metallic materials:: Correcting for the size of the plastic zone
K Durst et al.
SCRIPTA MATERIALIA (2005)
Deformation behavior of bimodal nanostructured 5083 Al alloys
BQ Han et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2005)
Investigation of creep behaviour under load during indentation experiments and its influence on hardness and modulus results
T Chudoba et al.
SURFACE & COATINGS TECHNOLOGY (2001)
Computational modeling of the forward and reverse problems in instrumented sharp indentation
M Dao et al.
ACTA MATERIALIA (2001)
Indentation size effect: Large grained aluminum versus nanocrystalline aluminum-zirconium alloys
AA Elmustafa et al.
SCRIPTA MATERIALIA (2000)
分享论文
