相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Microstructure evolution and mechanical property of ZrC-SiC/Ti6Al4V joints brazed using Ti-15Cu-15Ni filler
J. M. Shi et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)
Reinforcements stimulated dynamic recrystallization behavior and tensile properties of extruded (TiB + TiC + La2O3)/Ti6Al4V composites
Peikun Qiu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Interfacial microstructure and mechanical property of ZrC-SiC ceramic and Ti6A14V joint brazed with AgCuTi alloy
J. M. Shi et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)
Relief of the residual stresses in Si3N4/Invar joints by multi-layered braze structure - Experiments and simulation
Tianpeng Wang et al.
CERAMICS INTERNATIONAL (2016)
Fabrication and characterization of precursor-derived non-oxide ZrC-SiC multiphase ultrahigh temperature ceramics
Shugang Chen et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)
Characteristics of Ti(C, N)/TiB composite layer on Ti-6Al-4V alloy produced by laser surface melting
Xian Zeng et al.
OPTICS AND LASER TECHNOLOGY (2016)
Control of residual stresses in 2Si-B-3C-N and Nb joints by the Ag-Cu-Ti plus Mo composite interlayer
Rui Pan et al.
MATERIALS & DESIGN (2016)
Tribological, electrochemical and in vitro biocompatibility properties of SiC reinforced composite coatings
Mitun Das et al.
MATERIALS & DESIGN (2016)
Microstructure and mechanical properties of in situ casting TiC/Ti6Al4V composites through adding multi-walled carbon nanotubes
Bin Ya et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Thermomechanical properties of a spark plasma sintered ZrC-SiC composite obtained by a precursor derived ceramic route
G. Antou et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Oxidation behavior of spark plasma sintered ZrC-SiC composites obtained from the polymer-derived ceramics route
David Pizon et al.
CERAMICS INTERNATIONAL (2014)
Microstructure and mechanical properties of the GH783/2.5D C/SiC joints brazed with Cu-Ti plus Mo composite filler
Xing Wang et al.
MATERIALS & DESIGN (2012)
Effect of Mo coating on the interface and mechanical properties of SiC fiber reinforced Ti6Al4V composites
Xian Luo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
High temperature tensile properties of in situ TiBw/Ti6Al4V composites with a novel network reinforcement architecture
L. J. Huang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Laser processing of SiC-particle-reinforced coating on titanium
Mitun Das et al.
SCRIPTA MATERIALIA (2010)
Electron microscopy study of reaction layers between single-crystal WC particle and Ti-6Al-4V after laser melt injection
Liqun Li et al.
ACTA MATERIALIA (2009)
In situ investigation of fracture behavior in monocrystalline WCp-reinforced Ti-6Al-4V metal matrix composites produced by laser melt injection
Dejian Liu et al.
SCRIPTA MATERIALIA (2008)
Interlayer of Al2O3-Cr functionally graded material for reduction of thermal stresses in alumina-heat resisting steel joints
Katarzyna Pietrzak et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2007)
Fabrication and thermal properties of a YSZ-NiCr joint with an interlayer of YSZ-NiCr functionally graded material
JQ Li et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2003)
The evolution of microstructure in a laser clad TiB-Ti composite coating
BJ Kooi et al.
ACTA MATERIALIA (2003)
SiCp/Ti6Al4V functionally graded materials produced by laser melt injection
YT Pei et al.
ACTA MATERIALIA (2002)