☆ 4.6 Article

The effect of ageing process on three-point bending strength and permeability of 3D printed sand molds

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Remote Sensing

Aerodynamics Effect of Holes in UAV Wings Modified for VTOL Capability

Laith S. Sawaqed et al.

Summary: This research explores the possibility of modifying the X8 Skywalker from a fixed-wing unmanned aerial vehicle into a convertiplane. Computational fluid dynamics and wind tunnel experiments were conducted to analyze the performance of different wing configurations. The results indicate that the proposed modifications can generate enough lift despite reducing the wing area, with the filleted hole configuration demonstrating less drag and turbulence effects at low angles of attack.

DRONE SYSTEMS AND APPLICATIONS (2022)

添加到收藏夹

Article Automation & Control Systems

Investigating surface roughness of ZE41 magnesium alloy cast by low-pressure sand casting process

A. Sanitas et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

添加到收藏夹

Article Engineering, Chemical

Perspective on 3D printing of separation membranes and comparison to related unconventional fabrication techniques

Ze-Xian Low et al.

JOURNAL OF MEMBRANE SCIENCE (2017)

添加到收藏夹

Review Engineering, Manufacturing

3D printing for rapid sand casting-A review

Meet Upadhyay et al.

JOURNAL OF MANUFACTURING PROCESSES (2017)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Numerical modeling of the gas evolution in furan binder-silica sand mold castings

Laurentiu Nastac et al.

INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2016)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

QUANTIFYING THE ROLE OF PART DESIGN COMPLEXITY IN USING 3D SAND PRINTING FOR MOLDS AND CORES

Eyad S. Almaghariz et al.

INTERNATIONAL JOURNAL OF METALCASTING (2016)

添加到收藏夹

Article Engineering, Industrial

Dynamic measurements of the load on gray cast iron castings and contraction of castings during cooling in furan sand molds

Naoya Marumoto et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

添加到收藏夹

Article Engineering, Manufacturing

Effect of molding parameters on chemically bonded sand mold properties

Himanshu Khandelwal et al.

JOURNAL OF MANUFACTURING PROCESSES (2016)

添加到收藏夹

Article Engineering, Manufacturing

Effect of Binder Composition on the Shrinkage of Chemically Bonded Sand Cores

Himanshu Khandelwal et al.

MATERIALS AND MANUFACTURING PROCESSES (2015)

添加到收藏夹

Article Engineering, Industrial

A verification of the thermal stress analysis, including the furan sand mold, used to predict the thermal stress in castings

Yuichi Motoyama et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)

添加到收藏夹

Article Automation & Control Systems

Effects of layer thickness and binder saturation level parameters on 3D printing process

Mohammad Vaezi et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)

添加到收藏夹

Article Automation & Control Systems

Efficacy of powder-based three-dimensional printing (3DP) technologies for rapid casting of light alloys

Simranpreet Singh Gill et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)

添加到收藏夹

Article Engineering, Environmental

Emission of organic compounds from mould and core binders used for casting iron, aluminium and bronze in sand moulds

Niels Tiedje et al.

JOURNAL OF ENVIRONMENTAL SCIENCE AND HEALTH PART A-TOXIC/HAZARDOUS SUBSTANCES & ENVIRONMENTAL ENGINEERING (2010)

添加到收藏夹

Article Engineering, Mechanical

Direct metal rapid casting: mechanical optimization and tolerance calculation

Elena Bassoli et al.

RAPID PROTOTYPING JOURNAL (2009)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.