相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。Crack Repair in Aerospace Aluminum Alloy Panels by Cold Spray
P. Cavaliere et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2017)
Microstructural and fatigue behavior of cold sprayed Ni-based superalloys coatings
P. Cavaliere et al.
SURFACE & COATINGS TECHNOLOGY (2017)
Chlorine-induced high temperature corrosion of Inconel 625 sprayed coatings deposited with different thermal spray techniques
Davide Fantozzi et al.
SURFACE & COATINGS TECHNOLOGY (2017)
Crystallization Evolution of Cold-Sprayed Pure Ni Coatings
P. Cavaliere et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2016)
Characterization of Cold-Sprayed IN625 and NiCr Coatings
Dheepa Srinivasan et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2016)
Effect of sintering on mechanical properties of cold sprayed thermal barrier coatings
A. C. Karaoglanli et al.
SURFACE ENGINEERING (2016)
Localisation of deformation in cold gas dynamic spraying
O. Bielousova et al.
SURFACE ENGINEERING (2016)
Fatigue behaviour of cold sprayed metals and alloys: critical review
P. Cavaliere et al.
SURFACE ENGINEERING (2016)
Fatigue behavior of cold spray coatings: The effect of conventional and severe shot peening as pre-/post-treatment
A. Moridi et al.
SURFACE & COATINGS TECHNOLOGY (2015)
Evaluation of NiCoCrAlY coatings deposited on superalloy with novel cold spray process
S. B. S. Kalsi et al.
SURFACE ENGINEERING (2015)
Microstructure study of cold sprayed 50%Ni-50%Cr coating on Inconel-601
H. Singh et al.
SURFACE ENGINEERING (2015)
Fatigue strength of Al alloy cold sprayed with nanocrystalline powders
Ramin Ghelichi et al.
INTERNATIONAL JOURNAL OF FATIGUE (2014)
Mechanical properties of Inconel 625 laser cladded coatings: Depth sensing indentation analysis
D. Verdi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Influence of powder injection point position on efficiency of powder preheating in cold spray: Numerical study
A. Sova et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Performance of cold spray coatings on Fe-based superalloy in Na2SO4-NaCl environment at 900 °C
Sukhminderbir Singh Kalsi et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Mechanical properties of Inconel 625 cold-sprayed coatings after laser remelting. Depth sensing indentation analysis
P. Poza et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Effect of Particle Morphology and Size Distribution on Cold-Sprayed Pure Titanium Coatings
W. Wong et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2013)
Residual stresses in cold spray Al coatings: The effect of alloying and of process parameters
K. Spencer et al.
SURFACE & COATINGS TECHNOLOGY (2012)
Toughness evaluation of hard coatings and thin films
Sam Zhang et al.
THIN SOLID FILMS (2012)
Influence of Pre-Heated Al 6061 Substrate Temperature on the Residual Stresses of Multipass Al Coatings Deposited by Cold Spray
Silvano Rech et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2011)
On Parameter Selection in Cold Spraying
H. Assadi et al.
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2011)
On the characterization of bulk copper produced by cold gas dynamic spray processing in as fabricated and annealed conditions
Paul D. Eason et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Modified ball bond shear test for determination of adhesion strength of cold spray splats
Richard R. Chromik et al.
SURFACE & COATINGS TECHNOLOGY (2010)
Fatigue properties and crack behavior of ultra-fine and nanocrystalline pure metals
P. Cavaliere
INTERNATIONAL JOURNAL OF FATIGUE (2009)
Influence of substrate hardness on deposition behavior of single porous WC-12Co particle in cold spraying
Pei-Hu Gao et al.
SURFACE & COATINGS TECHNOLOGY (2008)
Cold gas dynamic manufacturing: A non-thermal approach to freeform fabrication
J. Pattison et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Nonlinear behavior in compression and tension of thermally sprayed ceramic coatings
F. Kroupa
JOURNAL OF THERMAL SPRAY TECHNOLOGY (2007)
Simulation of solid particle impact behavior for spray processes
Kensuke Yokoyama et al.
MATERIALS TRANSACTIONS (2006)
Adiabatic shear instability based mechanism for particles/substrate bonding in the cold-gas dynamic-spray process
M Grujicic et al.
MATERIALS & DESIGN (2004)
Computational analysis of the interfacial bonding between feed-powder particles and the substrate in the cold-gas dynamic-spray process
M Grujicic et al.
APPLIED SURFACE SCIENCE (2003)
Fracture mechanics analysis of coating/substrate systems Part I: Analysis of tensile and bending experiments
SR Kim et al.
ENGINEERING FRACTURE MECHANICS (2000)
分享论文
