相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Sustainable utilisation of low-grade and contaminated waste glass fines as a partial sand replacement in structural concrete
Tianchun Wang et al.
CASE STUDIES IN CONSTRUCTION MATERIALS (2022)
Extrusion-based concrete 3D printing from a material perspective: A state-of-the-art review
Manu K. Mohan et al.
CEMENT & CONCRETE COMPOSITES (2021)
A compendious review on lack-of-fusion in digital concrete fabrication
Jacques Kruger et al.
ADDITIVE MANUFACTURING (2021)
An investigation into the porosity of extrusion-based 3D printed concrete
Jacques Kruger et al.
ADDITIVE MANUFACTURING (2021)
Cementitious composites blending with high belite sulfoaluminate and medium-heat Portland cements for largescale 3D printing
Li Wang et al.
ADDITIVE MANUFACTURING (2021)
The effect of restrained early age shrinkage on the interlayer bond and durability of 3D printed concrete
G. M. Moelich et al.
JOURNAL OF BUILDING ENGINEERING (2021)
Experimental investigations on the effect of concrete quality, exposure conditions and duration of initial moist curing on carbonation rate in concretes exposed to urban, inland environment
Mike Otieno et al.
CONSTRUCTION AND BUILDING MATERIALS (2020)
Robust Sensor Suite Combined With Predictive Analytics Enabled Anomaly Detection Model for Smart Monitoring of Concrete Sewer Pipe Surface Moisture Conditions
Karthick Thiyagarajan et al.
IEEE SENSORS JOURNAL (2020)
Neutron radiography to study the water ingress via the interlayer of 3D printed cementitious materials for continuous layering
J. Van der Putten et al.
CONSTRUCTION AND BUILDING MATERIALS (2020)
Effects of layer-interface properties on mechanical performance of concrete elements produced by extrusion-based 3D-printing
Venkatesh Naidu Nerella et al.
CONSTRUCTION AND BUILDING MATERIALS (2019)
Corrosion propagation in cracked reinforced concrete, toward determining residual service life
Schalk R. Bezuidenhout et al.
STRUCTURAL CONCRETE (2019)
Durability, service life prediction, and modelling for reinforced concrete structures - review and critique
Mark Alexander et al.
CEMENT AND CONCRETE RESEARCH (2019)
3D concrete printing: A lower bound analytical model for buildability performance quantification
Jacques Kruger et al.
AUTOMATION IN CONSTRUCTION (2019)
Microstructural Characterization of 3D Printed Cementitious Materials
Jolien Van Der Putten et al.
MATERIALS (2019)
Influence of loading cracks on the carbonation resistance of RC elements
Vedran Carevic et al.
CONSTRUCTION AND BUILDING MATERIALS (2019)
Corrosion Challenges and Opportunities in Digital Fabrication of Reinforced Concrete
M. Stefanoni et al.
FIRST RILEM INTERNATIONAL CONFERENCE ON CONCRETE AND DIGITAL FABRICATION - DIGITAL CONCRETE 2018 (2019)
Effects of micro-environmental climate on the carbonation depth and the pH value in fly ash concrete
Cai-feng Lu et al.
JOURNAL OF CLEANER PRODUCTION (2018)
Chloride-induced corrosion of steel in cracked concrete - Part I: Experimental studies under accelerated and natural marine environments
M. Otieno et al.
CEMENT AND CONCRETE RESEARCH (2016)
Chloride ingress in cracked and uncracked SHCC under cyclic wetting-drying exposure
Suvash Chandra Paul et al.
CONSTRUCTION AND BUILDING MATERIALS (2016)
Oxygen permeability of concrete and its relation to carbonation
B. G. Salvoldi et al.
CONSTRUCTION AND BUILDING MATERIALS (2015)
Performance-based design and carbonation of concrete with high fly ash content
A. Younsi et al.
CEMENT & CONCRETE COMPOSITES (2011)
Corrosion in cracked and uncracked concrete - influence of crack width, concrete quality and crack reopening
M. B. Otieno et al.
MAGAZINE OF CONCRETE RESEARCH (2010)
The influence of binder type, cracking and cover on corrosion rates of steel in chloride-contaminated concrete
A. Scott et al.
MAGAZINE OF CONCRETE RESEARCH (2007)
On-site measurements of corrosion rate of reinforcements
C Andrade et al.
CONSTRUCTION AND BUILDING MATERIALS (2001)