☆ 4.6 Article

Properties of Slag-Fly Ash Blended Geopolymer Concrete Reinforced with Hybrid Glass Fibers

BUILDINGS (2022)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Ceramics

Effect of fiber factor on the workability and mechanical properties of polyethylene fiber-reinforced high toughness geopolymers

Cheng-feng Hu et al.

Summary: In this study, the influence of fiber factor on the workability, mechanical properties, and internal defects of PE fiber-reinforced high toughness geopolymers was investigated. Two specific fiber parameters, critical fiber factor and dense fiber factor, were proposed. The results showed that the fiber factor significantly affected the workability and mechanical properties of the material within a certain range, and the selection of fiber parameters was crucial for achieving satisfactory workability and excellent mechanical properties.

CERAMICS INTERNATIONAL (2022)

添加到收藏夹

Article Construction & Building Technology

Optimization of alkali-activated ladle slag composites mix design using taguchi-based TOPSIS method

Omar Najm et al.

Summary: This study investigates the impact of various parameters on the properties of alkali-activated composites made with unprocessed ladle furnace slag. By using the Taguchi method, a series of experiments were designed, and the optimal mixture proportions were determined using TOPSIS analysis. The results show that the optimum mix can maximize strength and workability or maximize workability and setting time.

CONSTRUCTION AND BUILDING MATERIALS (2022)

添加到收藏夹

Review Construction & Building Technology

A scientometric review on mechanical and durability performance of geopolymer Paste: Effect of various raw materials

Ali Raza et al.

Summary: This research assesses the microstructural, fresh, hardened, and durability characteristics of geopolymer paste. The influence of alkaline solution forms, concentrations, activators, mix proportioning, curing conditions, and additives is investigated.

CONSTRUCTION AND BUILDING MATERIALS (2022)

添加到收藏夹

Article Construction & Building Technology

Key parameters establishing alkali activation effects on stabilized rammed earth

Nilo Cesar Consoli et al.

Summary: This study assessed the effectiveness of a specific type of alkali activated cement (AAC) for the stabilization of rammed sand. The experimental investigation focused on the mechanical performance and microstructure of the sand-cement blends, considering the influence of the activator and curing period. The results showed that the presence of the activator significantly influenced the mechanical behavior, with an optimum concentration of 3 molal. The mineralogical and microscopic analysis revealed the formation of a heterogeneous cementitious matrix with a structure distinct from traditional cement.

CONSTRUCTION AND BUILDING MATERIALS (2022)

添加到收藏夹

Article Green & Sustainable Science & Technology

Development and Optimization of Geopolymers Made with Desert Dune Sand and Blast Furnace Slag

Abdulkader El-Mir et al.

Summary: This study assesses the effect of mix design parameters on the properties and cost of geopolymer mortar, and uses Taguchi method in experimental design. The results show that up to 25% DDF replacement enhances the density, strength, and durability of the geopolymers. Other factors have limited contributions. The TOPSIS method determines the optimal mix proportions.

SUSTAINABILITY (2022)

添加到收藏夹

Article Materials Science, Ceramics

Enhancement of mechanical and toughness properties of carbon fiber-reinforced geopolymer pastes comprising nano calcium oxide

Mohamed Hechmi El Ouni et al.

Summary: This study investigates the influence of nano calcium oxide and micro carbon fiber on the properties of GPMR paste. The results show that the application of nano calcium oxide can improve the strength and toughness of GPMR paste when used in appropriate quantities.

JOURNAL OF THE AUSTRALIAN CERAMIC SOCIETY (2022)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Synthesis of Fly-ash and Slag Based Geopolymer Concrete for Rigid Pavement

M. G. Girish et al.

Summary: This research work focuses on the synthesis of Geopolymer concrete using fly-ash and granulated blast furnace slag for paving applications. The study found that using 25% to 30% GGBS and 8 M to 10 M NaOH solution can meet the criteria of paving grade concrete standards.

MATERIALS TODAY-PROCEEDINGS (2022)

添加到收藏夹

Article Construction & Building Technology

Geopolymer- and Cement-Based Fabric-Reinforced Matrix Composites for Shear Strengthening of Concrete Deep Beams: Laboratory Testing and Numerical Modeling

Nour Khir Allah et al.

Summary: This paper examines the effectiveness of using carbon fabric-reinforced matrix (C-FRM) composites to improve the shear response of reinforced concrete (RC) deep beams. The experimental results show that the use of C-FRM can significantly increase the shear strength of deep beams, with the most significant effect observed when using a cementitious matrix. The numerical modeling results are in good agreement with the experimental results.

BUILDINGS (2022)

添加到收藏夹

Article Multidisciplinary Sciences

Mechanical Performance of Geopolymer Composites Containing Nano-Silica and Micro-Carbon Fibers

Ali Raza et al.

Summary: By adding different contents of nano-silica, this study successfully enhanced the mechanical and fracture efficacy of micro-carbon fiber reinforced GEOP pastes. The results demonstrated that 3% NSI in conjunction with 0.5% micro-CF showed optimal measurements for mechanical and fracture properties, making it the most beneficial combination for practical applications in developing a sustainable environment.

ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2022)

添加到收藏夹

Article Construction & Building Technology

Experimental investigation on the mechanical and fracture evaluation of carbon Fiber-Reinforced cementitious composites with Nano-Calcium carbonate

Liaqat Ali et al.

Summary: Research examines the improvement of mechanical and microstructural efficiency of micro carbon-FR fly ash-based GPM mixes by incorporating different quantities of nano calcium carbonate. Test results show that using 3% nano calcium carbonate in carbon-FR-GPM mix yields optimal results for hardness and compressive strength, while employing 2% nano calcium carbonate yields optimal flexural strength, fracture toughness, and impact strength of composites.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

Enhancing the performance of Alkali-Activated Slag-Fly ash blended concrete through hybrid steel fiber reinforcement

Hilal El-Hassan et al.

Summary: Hybrid combinations of steel fibers at a specific dosage led to superior mechanical properties of ambient-cured alkali-activated slag-fly ash blended concrete compared to those without fibers or with a single type of fiber. Cost-benefit analysis demonstrated that such hybrid mixes were the most cost-effective option for applications demanding high strength and low cost. Newly developed multifunctional performance indices highlighted the optimum mixes incorporating hybrid steel fibers.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

Strength, durability, and microstructure of geopolymers based on recycled-glass powder waste and dolomitic lime for soil stabilization

Jair J. A. Baldovino et al.

Summary: The study found that the microstructure and mechanical properties of soil-GP-dolomitic lime compacted blends improved with increasing GP contents, leading to a decrease in accumulated loss of mass. All these results were dependent on a novel index, the ratio of porosity to volumetric binder content.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Polymer Science

Mechanical, Fracture, and Microstructural Assessment of Carbon-Fiber-Reinforced Geopolymer Composites Containing Na2O

Ahmad Rashedi et al.

Summary: The study found that the addition of 3% nano-sodium dioxide significantly improved the mechanical properties and microstructure of carbon-fiber-reinforced geopolymer paste, enhancing various indicators such as compressive strength, flexural strength, and elastic modulus.

POLYMERS (2021)

添加到收藏夹

Review Construction & Building Technology

Geopolymer concrete durability subjected to aggressive environments - A review of influence factors and comparison with ordinary Portland cement

Keyu Chen et al.

Summary: Geopolymer concrete, as a potential substitute for ordinary Portland cement (OPC), has shown better durability in aggressive environments compared to OPC concrete. Factors influencing durability and interactions in geopolymer concrete have been highlighted, along with suggestions for future studies on durability during life-cycle periods.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

Stress-Strain Relationship of Steel Fiber Reinforced Alkali Activated Slag Concrete under Static Compression

Xiaohui Yuan et al.

Summary: The stress-strain curve accurately reflects the mechanical behavior of steel fiber reinforced alkali activated slag concrete, with strength, Young's Elastic Modulus, and Poisson's ratio increasing with steel fiber content. A damage evolution model was established using Weibull and Cauchy distribution, accurately describing the key points in the concrete materials stress-strain curve. The accuracy of the model was verified by comparing test stress-strain relationship curves.

ADVANCES IN CIVIL ENGINEERING (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Properties of Steel Fiber-Reinforced Alkali-Activated Slag Concrete Made with Recycled Concrete Aggregates and Dune Sand

Hilal El-Hassan et al.

Summary: The study found that replacing 30% and 70% of natural aggregates with RCA in concrete did not decrease compressive strength, while full replacement of NA with RCA resulted in a 20% decrease in compressive strength. In order to achieve compressive strength comparable to that of an NA-based mix, 100% RCA mixes required 2% volume of steel fibers. Overall, incorporating steel fibers in RCA-based mixes improved mechanical properties and resistance to abrasion, water permeation, and transport compared to NA-based mixes.

SUSTAINABILITY (2021)

添加到收藏夹

Article Construction & Building Technology

Effect of curing regime on the performance and microstructure characteristics of alkali-activated slag-fly ash blended concrete

Hilal El-Hassan et al.

Summary: The study found that the optimal curing regime for alkali-activated blended concrete made with 0% and 25% fly ash was a combination of water and subsequent air curing, while that for mixes made with 50% fly ash was continuous water curing. The mix incorporating 25% fly ash exhibited superior properties compared to other mixtures.

JOURNAL OF SUSTAINABLE CEMENT-BASED MATERIALS (2021)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Effect of curing on mechanical strength and microstructure of fly ash blend GGBS geopolymer, Portland cement mortar and its behavior at elevated temperature

N. Poornima et al.

Summary: The experimental work compared the mechanical strength, thermal resistance, and microstructural characteristics of geopolymer cement and traditional Portland cement under different curing conditions. The optimal combination of PEG has been determined to enhance the C-S-H gel in geopolymer cement. The use of PEG can improve the permeability and overall performance of geopolymer cement.

MATERIALS TODAY-PROCEEDINGS (2021)

添加到收藏夹

Article Construction & Building Technology

Performance of Steel Fiber-Reinforced Alkali-Activated Slag-Fly Ash Blended Concrete Incorporating Recycled Concrete Aggregates and Dune Sand

Hilal El-Hassan et al.

Summary: The study found that the replacement of natural aggregates with recycled concrete aggregates led to a decrease in compressive strength, but this could be partially compensated by incorporating steel fibers. Additionally, RCA replacement resulted in increased water absorption and decreased ultrasonic pulse velocity, while the inclusion of steel fibers improved concrete density and resistance to abrasion.

BUILDINGS (2021)

添加到收藏夹

Article Construction & Building Technology

Bond Behavior of Carbon Fabric-Reinforced Matrix Composites: Geopolymeric Matrix versus Cementitious Mortar

Feras Abu Obaida et al.

Summary: This study investigated the use of a geopolymeric matrix as an alternative to commercial mortars in carbon fabric-reinforced matrix composites. The geopolymeric matrix exhibited higher fabric strains, ultimate loads, and a steeper strain profile compared to a cementitious matrix. New bond-slip models were developed to characterize the bond behavior at the fabric-matrix interface for both types of matrices, showing equal maximum shear stress but higher fracture energy and slip for the geopolymeric matrix.

BUILDINGS (2021)

添加到收藏夹

Article Construction & Building Technology

A step towards durable, ductile and sustainable concrete: Simultaneous incorporation of recycled aggregates, glass fiber and fly ash

Babar Ali et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Review Construction & Building Technology

The influence of steel fibres on compressive and tensile strength of ultra high performance concrete: A review

Ingrid Lande Larsen et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Green & Sustainable Science & Technology

The Impact of the Amount of Water Used in Activation Solution and the Initial Temperature of Paste on the Rheological Behaviour and Structural Evolution of Metakaolin-Based Geopolymer Pastes

Laura Vitola et al.

SUSTAINABILITY (2020)

添加到收藏夹

Article Construction & Building Technology

Effect of steel fibers on the performance of concrete made with recycled concrete aggregates and dune sand

Nancy Kachouh et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Construction & Building Technology

Performance Evaluation and Microstructure Characterization of Steel Fiber-Reinforced Alkali-Activated Slag Concrete Incorporating Fly Ash

Hilal El-Hassan et al.

JOURNAL OF MATERIALS IN CIVIL ENGINEERING (2019)

添加到收藏夹

Article Construction & Building Technology

Development and Characterization of Fly Ash-Slag Blended Geopolymer Mortar and Lightweight Concrete

Najif Ismail et al.

JOURNAL OF MATERIALS IN CIVIL ENGINEERING (2018)

添加到收藏夹

Article Construction & Building Technology

Influence of Different Curing Regimes on the Performance and Microstructure of Alkali-Activated Slag Concrete

Hilal El-Hassan et al.

JOURNAL OF MATERIALS IN CIVIL ENGINEERING (2018)

添加到收藏夹

Article Construction & Building Technology

Alkali-resistant glass fiber reinforced high strength concrete in simulated aggressive environment

W. H. Kwan et al.

MATERIALES DE CONSTRUCCION (2018)

添加到收藏夹

Review Construction & Building Technology

Structural and material performance of geopolymer concrete: A review

Chau-Khun Ma et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Effect of process parameters on the performance of fly ash/GGBS blended geopolymer composites

Hilal El-Hassan et al.

JOURNAL OF SUSTAINABLE CEMENT-BASED MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Estimation of geopolymer concrete strength from ultrasonic pulse velocity (UPV) using high power pulser

Rachit Ghosh et al.

JOURNAL OF BUILDING ENGINEERING (2018)

添加到收藏夹

Article Green & Sustainable Science & Technology

Low carbon building: Experimental insight on the use of fly ash and glass fibre for making geopolymer concrete

Thangaraj Sathanandam et al.

SUSTAINABLE ENVIRONMENT RESEARCH (2017)

添加到收藏夹

Article Construction & Building Technology

On drying shrinkage in alkali-activated concrete: Improving dimensional stability by aging or heat-curing

R. J. Thomas et al.

CEMENT AND CONCRETE RESEARCH (2017)

添加到收藏夹

Article Construction & Building Technology

Effect of water addition, plasticizer and alkaline solution constitution on fly ash based geopolymer concrete performance

Ali A. Aliabdo et al.

CONSTRUCTION AND BUILDING MATERIALS (2016)

添加到收藏夹

Article Construction & Building Technology

Compressive Stress-Strain Relationship of High Strength Steel Fiber Reinforced Concrete

Wen-Cheng Liao et al.

Journal of Advanced Concrete Technology (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Workability Analysis of Steel Fiber Reinforced Concrete Using Slump and Ve-Be Test

Antonio Domingues de Figueiredo et al.

MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2015)

添加到收藏夹

Article Construction & Building Technology

Effect of initial water content and curing moisture conditions on the development of fly ash-based geopolymers in heat and ambient temperature

Jiting Xie et al.

CONSTRUCTION AND BUILDING MATERIALS (2014)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Properties of Fresh and Hardened Glass Fiber Reinforced Fly Ash Based Geopolymer Concrete

Behzad Nematollahi et al.

ADVANCED MATERIALS ENGINEERING AND TECHNOLOGY II (2014)

添加到收藏夹

Review Green & Sustainable Science & Technology

Global strategies and potentials to curb CO2 emissions in cement industry

Emad Benhelal et al.

JOURNAL OF CLEANER PRODUCTION (2013)

添加到收藏夹

Article Construction & Building Technology

Tensile behavior of Ultra High Performance Hybrid Fiber Reinforced Concrete

Seung Hun Park et al.

CEMENT & CONCRETE COMPOSITES (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of granulated blast furnace slag on the reaction, structure and properties of fly ash based geopolymer

Sanjay Kumar et al.

JOURNAL OF MATERIALS SCIENCE (2010)

添加到收藏夹

Article Construction & Building Technology

Compressive Stress-Strain Behavior of Small Scale Steel Fibre Reinforced High Strength Concrete Cylinders

Pradeep Bhargava et al.

JOURNAL OF ADVANCED CONCRETE TECHNOLOGY (2006)

添加到收藏夹

Article Construction & Building Technology

The coexistence of geopolymeric gel and calcium silicate hydrate at the early stage of alkaline activation

CK Yip et al.

CEMENT AND CONCRETE RESEARCH (2005)

添加到收藏夹

Article Multidisciplinary Sciences

Capturing greenhouse gases

H Herzog et al.

SCIENTIFIC AMERICAN (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.