☆ 4.7 Article

Effect of substrate orientations on the electrochemical and localized corrosion behavior of a quad-layer Al alloy composite

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Metallurgy & Metallurgical Engineering

Complex films formed on Al alloy surface via vapor phase assembly of benzotriazole and dodecyltrimethoxysilane

Qiang Wang et al.

Summary: The effect of vapor assembly sequence and assembly temperature on the corrosion protection of complex silane films on Al alloy was studied. The performance and application range of silane films were improved. Electrochemical measurements and alkaline solution accelerated corrosion test were used to investigate the corrosion protection of the assembly films. Thickness and hydrophobicity of the complex films were studied using ellipsometric spectroscopy and contact angle tests.

ANTI-CORROSION METHODS AND MATERIALS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the localized corrosion of AA5083 in a simulated dynamic seawater/air interface-Part 1: Corrosion initiation mechanism

Da-Hai Xia et al.

Summary: Localized corrosion of aluminium alloy AA5083-H111 was studied in both a simulated dynamic seawater/air interfacial zone and a full seawater immersion zone using electrochemical impedance spectroscopy and electrochemical noise. Investigation of Al-Fe/Ti intermetallic particles (IMPs) on localized corrosion was conducted with focused ion beam, transmission electron microscopy, and energy dispersive X-ray spectroscopy. Compared to the full immersion zone, the interfacial zone exhibited higher oxide film resistance and charge transfer resistance, attributed to the elevated oxygen flux in that zone. The localized corrosion was found to originate from IMPs containing an Al-Fe phase and a Ti enriched phase.

CORROSION SCIENCE (2023)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Identifying the cavitation erosion stages of AA5083 by electrochemical noise analyses

Yesen Zhu et al.

Summary: The purpose of this paper is to study the cavitation erosion stages of AA5083 by using electrochemical noise (EN). EN technology including noise resistance and fast Fourier transform were used to characterize the electrochemical process during the cavitation erosion process. The findings show that AA5083 suffers from uniform corrosion during the cavitation erosion process, which can be divided into three stages: incubation stage, acceleration stage and steady-state stage. EN signals showed obvious differences in different stages of cavitation erosion. The originality and value of this study lie in the suitability of EN technique for studying cavitation erosion mechanism and identifying cavitation erosion stages.

ANTI-CORROSION METHODS AND MATERIALS (2023)

添加到收藏夹

Article Electrochemistry

Corrosion behavior of a five-layer Al alloy composite plate in NaCl solution

Dejing Zhou et al.

ANTI-CORROSION METHODS AND MATERIALS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Galvanic corrosion of AA5052/304SS welded joint with Zn-based filler metal in marine engineering

Yueting Ma et al.

Summary: The galvanic corrosion and localized corrosion behavior of AA5052/weld seam/304SS tri-metallic couples were investigated using various tests after TIG arc welding. The results showed that the weld seam is susceptible to corrosion. The asymmetric corrosion of the weld seam is attributed to the macro-galvanic effect between the weld seam/AA and the weld seam/SS. The localized corrosion of Zn in delta-FeZn10 resulted in the initiation of corrosion trenches and channels. The deep corrosion propagation at the weld seam/SS interface was caused by local acidity and micro-galvanic effect.

CORROSION SCIENCE (2023)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Surface modification of Al alloy by self-assembly dodecyl phosphate/cerium composite film as relevant to offshore floating photovoltaic power

Bin Wang et al.

Summary: This paper aims to prepare a composite film on LY12 aluminum alloy by immersing in dodecyl phosphate and cerium nitrate solution by self-assembling methods. The effect of dipping sequence in dodecyl phosphate and cerium nitrate solution on the corrosion resistance of the composite film is studied.

ANTI-CORROSION METHODS AND MATERIALS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Understanding the interaction between erosion and corrosion of pipeline steel in acid solution of different pH

Yunze Xu et al.

Summary: The interactions between erosion and corrosion of X65 pipeline steel in acid slurry were investigated at different pH levels. Results showed that pH = 3.5 was a critical value for the transition of cathodic reaction under erosion-corrosion. The reduction of Hthorn was the main cathodic reaction at pH < 3.5, leading to scattered small pits. However, at pH >= 3.5, oxygen reduction became the main cathodic reaction, resulting in the formation of erosion-corrosion pits and craters.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Engineering, Manufacturing

Corrosion susceptibility of different planes of AlMgScZr alloy produced by selective laser melting

Y. X. Chen et al.

Summary: This study investigates the corrosion susceptibility of the Top and Side plane of the AlMgScZr alloy manufactured by selective laser melting (SLM) through electrochemical tests. The results show that the Top plane exhibits better corrosion resistance due to its better grain distribution and weaker texture relative to the Side plane.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Identification of the critical microstructural parameters on the corrosion behaviour of commercially pure aluminium alloy

A. Ingle et al.

Summary: The study found that an increase in the density of high-angle grain boundaries can decrease the corrosion current of commercially pure Al alloy in chloride-sulphate solution, while intermetallic particles may act as pit initiation sites. In addition, the propagation of pits is strongly influenced by the density of high-angle grain boundaries.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Improvement of mechanical properties of tri-metallic 7075Al/1060Al/304 SS composite via collaborative strengthening behavior

Taiqian Mo et al.

Summary: This study systematically investigates the mechanical behavior of tri-metallic Al/Al/Steel composites, focusing on the effect of strengthening mechanisms introduced by interlaminar and internal microstructures. The results show that the tri-metallic composites exhibit excellent interface bonding and inhibited intermetallic compound formation. The mechanical properties of the tri-metallic composites are significantly improved compared to bi-metallic Al/Steel composites due to the precipitation strengthening behavior of the high-performance 7075Al. Various annealing treatments are conducted to further optimize the strength and ductility of the tri-metallic composites by inducing strengthening mechanisms near the interface.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Electrochemical and localized corrosion behavior of 316 L SS/copper/316 L SS sandwich composite in chloride-containing environment

Huajie Tang et al.

Summary: In this study, the electrochemical and localized corrosion behavior of a 316L SS/copper/316L SS composite in a 0.5 wt. % NaCl solution was investigated using electrochemical measurements and high-resolution microscopic examination. Galvanic coupling accelerated the dissolution at the internal surface and pitting attack at the external surface of the 316L layer. Polarization up to 1 V/SCE resulted in the formation of a corrosion product layer composed of metal oxides/hydroxides on top of the passive film.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of post-brazing heat treatment on the corrosion mechanism of sandwich multi-layered aluminium sheets

Zhipeng Yuan et al.

Summary: Post-brazing heat treatment at 325 degrees C leads to homogenous dispersion of Cu in the re-solidified clad and elimination of Al2Cu particles. Additionally, a large number of alpha-Al(Fe,Mn)Si particles precipitate in the diffusion zone after the treatment, making it slightly more anodic and enhancing its sacrificial protection capability for the core layer.

VACUUM (2021)

添加到收藏夹

Review Metallurgy & Metallurgical Engineering

Review of micro-scale and atomic-scale corrosion mechanisms of second phases in aluminum alloys

Yuan-yuan Ji et al.

Summary: Localized corrosion of aluminum alloys, such as pitting corrosion, intergranular corrosion, and stress corrosion cracking, is closely related to micro-galvanic corrosion between the second phase and the Al matrix. Factors affecting the corrosion mechanisms of the second phase in Al alloys at micro and atomic scales were examined using high-resolution transmission electron microscopy and first principles calculations, including the composition and structure of the second phase, pH of the environment, stress, and adsorption behavior of adsorbates (such as CF, H2O, OH, and O-2).

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the corrosion of a high solute Al-Zn-Mg alloy produced by laser powder bed fusion

A. P. Babu et al.

Summary: The research examined an additively manufactured aluminium alloy with high solute content, Al-14Zn-3Mg, which showed lower corrosion rate compared to a conventional wrought alloy, AA7075-T6. This difference was attributed to the microstructure and solute content of Al-14Zn-3Mg, specifically the absence of coarse intermetallic particles. Various tests were conducted to analyze the corrosion behavior of this new alloy manufactured through LPBF.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Electrochemical profiling of multi-clad aluminium sheets used in automotive heat exchangers

Kirill Bordo et al.

CORROSION SCIENCE (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the AA2198-T851 alloy microstructure and its correlation with localized corrosion behaviour

Uyime Donatus et al.

CORROSION SCIENCE (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure-sensitive modeling of pitting corrosion: Effect of the crystallographic orientation

Patrick T. Brewick et al.

CORROSION SCIENCE (2017)

添加到收藏夹

Article Chemistry, Physical

Effect of Sr addition on the characteristics of as-cast and rolled 3003/4004 clad aluminum

Guangyuan Yan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure, texture and mechanical properties of Al/Al laminated composites fabricated by hot rolling

Z. J. Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of Al-Si-Mg alloys fabricated by twin roll casting and subsequent symmetric and asymmetric rolling

Jae-Hyung Cho et al.

METALS AND MATERIALS INTERNATIONAL (2014)

添加到收藏夹

Article Electrochemistry

Scanning Kelvin probe force microscopy as a means of predicting the electrochemical characteristics of the surface of a modified AA4xxx/AA3xxx (Al alloys) brazing sheet

F. Norouzi Afshar et al.

ELECTROCHIMICA ACTA (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Precipitation of partially coherent α-Al(Mn,Fe)Si dispersoids and their strengthening effect in AA 3003 alloy

Y. J. Li et al.

ACTA MATERIALIA (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of brazing process on microstructure evolution and corrosion performance of a modified AA4XXX/AA3XXX brazing sheet

F. Norouzi Afshar et al.

CORROSION SCIENCE (2012)

添加到收藏夹

Article Electrochemistry

Electrochemical depth profiling of multilayer metallic structures: An aluminum brazing sheet

F. Norouzi Afshar et al.

ELECTROCHIMICA ACTA (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of the reinforced boron carbide particulate content of AA6061 alloy on formation of the passive film in seawater

V. A. Katkar et al.

CORROSION SCIENCE (2011)

添加到收藏夹

Article Nanoscience & Nanotechnology

Evolution of deformation texture in Al/Al-Mg/Al composite sheets during cold-roll cladding

Eun-Young Kim et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)

添加到收藏夹

Article Electrochemistry

Determination of effective capacitance and film thickness from constant-phase-element parameters

Bryan Hirschorn et al.

ELECTROCHIMICA ACTA (2010)

添加到收藏夹

Article Electrochemistry

Constant-Phase-Element Behavior Caused by Resistivity Distributions in Films I. Theory

Bryan Hirschorn et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Role of second phase particles in pitting corrosion of 3003 Al alloy in NaCl solution

Y. Liu et al.

MATERIALS AND CORROSION-WERKSTOFFE UND KORROSION (2010)

添加到收藏夹

Article Electrochemistry

Electronic structure and pitting behavior of 3003 aluminum alloy passivated under various conditions

Y. Liu et al.

ELECTROCHIMICA ACTA (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Evolution of precipitation during different homogenization treatments in a 3003 aluminum alloy

Hsin-Wen Huang et al.

MATERIALS & DESIGN (2009)

添加到收藏夹

Article Electrochemistry

Mechanistic aspects of electrochemical corrosion of aluminum alloy in ethylene glycol-water solution

G. A. Zhang et al.

ELECTROCHIMICA ACTA (2008)

添加到收藏夹

Article Electrochemistry

CPE analysis by local electrochemical impedance spectroscopy

JB Jorcin et al.

ELECTROCHIMICA ACTA (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Electrochemical behaviors of quad-layer aluminum brazing sheet composite for automotive applications

Q Shi et al.

CORROSION (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.