☆ 4.7 Article

Hot deformation behavior and dynamic recrystallization of dual-phase (CrCoNi)94Al3Ta3 medium entropy alloy

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Jiaguo Tang et al.

Summary: In this study, isothermal compression tests were conducted on the 2195 Al-Cu-Li alloy to investigate its hot deformation behavior. A processing map was established to predict the workability under different conditions, and the corresponding microstructures were analyzed to reveal the deformation mechanisms. The results indicate that the optimal hot-working conditions for the alloy are at temperatures of 460-500 degrees C and strain rates of 10-3-10-2 s-1, with dominant mechanisms of dynamic recrystallization and dynamic recovery.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Chemistry, Physical

Research on hot deformation behavior and constitutive model to predict flow stress of an annealed FeCrCuNi2Mn2 high-entropy alloy

Seyyed Ali Sajadi et al.

Summary: In this study, the hot deformation and dynamic recrystallization behaviors of an annealed FeCrCuNi2Mn2 high-entropy alloy were investigated. The flow curves were evaluated and constitutive equations were established for the calculation of material constants and modeling of flow stress behavior. The results showed that the increase in deformation temperature and decrease in strain rate led to a decrease in dynamic recrystallization parameters, followed by an increase in recrystallized volume fraction and grain growth, resulting in a decrease in alloy hardness. The activation energy of hot deformation was determined to be 437 kJ/mol and a power equation was established between critical stress and strain and the Zener-Hollomon parameter.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Chemistry, Physical

Cryogenic tensile behavior of laser additive manufactured CoCrFeMnNi high entropy alloys

Eun Seong Kim et al.

Summary: In this study, the microstructural evolution, tensile properties, and deformation behavior of additively manufactured equiatomic CoCrFeMnNi high entropy alloy (HEA) were investigated at a cryogenic temperature of 77 K. The results showed that the HEA processed by direct energy deposition (DED) exhibited excellent strength and ductility at 77 K, with exceptional strain hardening, compared to the laser powder bed fusion (LPBF) and wrought samples. The formation of deformation twinning in addition to dislocation slip was observed as the deformation mechanism at 77 K.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Chemistry, Physical

Designing CoCrFeNi-M (M = Nb, Ta, Zr, and Hf) eutectic high-entropy alloys via a modified simple mixture method

Wenna Jiao et al.

Summary: Recently, a modified simple mixture method was proposed to design eutectic high-entropy alloys (EHEAs) containing more than five elements. Four novel six-element and seven-element EHEAs were designed and prepared, demonstrating the validity and accuracy of this method. The two seven-element EHEAs exhibited peak strengths of 592 and 660 MPa at 1073 K, surpassing most reported EHEAs and even some refractory high-entropy alloys (RHEAs). This study provides a significant paradigm for designing EHEAs with more than five elements.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Study on the microstructure evolution and dynamic recrystallization mechanism of selective laser melted Inconel 718 alloy during hot deformation

Wei Le et al.

Summary: In this study, the hot deformation behavior, microstructure evolution, and dynamic recrystallization (DRX) behavior of selective laser melted (SLM) 718 alloy were investigated using isothermal compression testing, electron back scattered diffraction (EBSD) technology, and transmission electron microscope (TEM). The results reveal that the deformation condition has a significant impact on the flow behavior and DRX grain of the alloy. Increasing the deformation temperature or decreasing the strain rate leads to an increase in the volume fraction and average size of DRX grains. The DRX mechanism of SLM 718 alloy involves discontinuous dynamic recrystallization (DDRX) characterized by initial grain boundary and regenerated grain boundary bulging, and continuous dynamic recrystallization (CDRX) occurring inside the grain characterized by progressive subgrain rotation and homogeneous misorientation increase.

VACUUM (2023)

添加到收藏夹

Article Chemistry, Physical

Effect of microstructural evolution on corrosion behavior of Al0.7Cr2FeCoNi high-entropy alloy

Xiaolei Yan et al.

Summary: In this study, the influence of microstructural evolution on the corrosion behavior of a B2 nanoprecipitation-strengthened BCC-based Al0.7Cr2FeCoNi high-entropy alloy in a 3.5 mass% NaCl solution was investigated. The results showed that the alloy exhibited good corrosion resistance and formed Cr-rich surface films. However, heat treatment at higher temperatures led to a decrease in corrosion resistance due to the increased potential difference between the B2 and σ phases and the coarsening of the Cr-depleted B2 particles. Therefore, to obtain corrosion-resistant high-entropy alloys, the coarsening of B2 particles and precipitation of σ phase should be suppressed.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior and flow stress modeling of a novel CoNi-based wrought superalloy

Huiwei Li et al.

Summary: The thermal deformation behavior and flow stress modeling of a novel CoNi-based wrought superalloy were investigated at different temperatures and strain rates, showing dynamic recrystallization occurring under all deformation conditions. Additionally, when the alloy was deformed sub-solvusly at higher temperatures and lower strain rates, the gamma' phase dissolved resulting in substantial grain growth.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Quantitative Nanostructure and Hardness Evolution in Duplex Stainless Steels: Under Real Low-Temperature Service Conditions

Yadunandan Das et al.

Summary: This study investigates the phase separation phenomenon in duplex and super-duplex stainless steels at high temperatures, and its effect on mechanical property evolution. Quantitative measurements of the phase separated nanostructure were obtained using Small-Angle Neutron Scattering, and hardness models were used to predict the hardness evolution.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

The B2 phase-driven microstructural heterogeneities and twinning enable ultrahigh cryogenic strength and large ductility in NiCoCr-based medium-entropy alloy

D. D. Zhang et al.

Summary: This study designed a duplex medium-entropy alloy with outstanding mechanical responses at low temperatures, showing that its strength and ductility vary with temperature. The alloy exhibits excellent strength-ductility synergy, especially with unique B2 cracking behavior observed at low temperatures.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Chemistry, Physical

Atomistic understanding of incipient plasticity in BCC refractory high entropy alloys

Xiaorong Liu et al.

Summary: This study investigated the initial dislocation nucleation and motion mechanisms in TaTiZrV high-entropy alloys (RHEAs) and their dependence on temperature through molecular dynamics simulations. The short-range orders in the RHEA facilitate preferential inhomogeneous nucleation at low stress, while compositional fluctuation affects the slipping and moving rate of dislocations. Moreover, the difficulty of initial dislocation nucleation increases with temperature.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of hot isostatic pressing on the cryogenic mechanical properties of CrCoNi medium entropy alloy processed by direct energy deposition

Minh Tien Tran et al.

Summary: In this study, the effect of hot isostatic pressing (HIP) on the cryogenic mechanical properties of CrCoNi medium entropy alloy (MEA) fabricated by direct energy deposition (DED) was investigated. The HIP treated CrCoNi MEA-DED showed decreased strength, but an excellent combination of high strength and preserved elongation to fracture at 77 K. The mechanical properties at cryogenic temperature of the HIP treated CrCoNi MEA-DED were significantly better compared to other CrCoNi MEAs prepared by different processes.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Hot deformation behaviors of an ultrafine-grained MoNbTaTiV refractory high-entropy alloy fabricated by powder metallurgy

Qing Liu et al.

Summary: The hot deformation behaviors of ultrafine-grained MoNbTaTiV refractory high entropy alloy were studied, showing that flow stress decreases and grain size increases with increasing deformation temperature and decreasing strain rate. The dominant dynamic recrystallization process changed from discontinuous to continuous with increasing deformation temperature. Different deformation mechanisms were observed under different conditions.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Chemistry, Physical

Unique hot deformation behavior and microstructure evolution of a dual FCC-phase CoCrCu1.2FeNi high entropy alloy

Jufu Jiang et al.

Summary: The hot deformation behavior and microstructure evolution of the CoCrCu1.2FeNi high entropy alloy composed of two FCC phases were investigated through hot compression tests and EBSD analysis. Two optimized hot working regions were found and asynchronous dynamic recrystallization was observed. The DRX mechanism shifted from DDRX to CDRX with increasing temperature, leading to the formation of hot working defects.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Chemistry, Physical

Mechanism of grain refinement in an equiatomic medium-entropy alloy CrCoNi during hot deformation

Guoai He et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Multidisciplinary Sciences

Dual heterogeneous structures lead to ultrahigh strength and uniform ductility in a Co-Cr-Ni medium-entropy alloy

X. H. Du et al.

NATURE COMMUNICATIONS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Cr addition on the constitutive equation and precipitated phases of copper alloy during hot deformation

Yijie Ban et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior and workability of a Ni-Co based superalloy

Peng Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of cryogenic temperature and grain size on fatigue-crack propagation in the medium-entropy CrCoNi alloy

Julian Rackwitz et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Engineering, Mechanical

A CDRX-based material model for hot deformation of aluminium alloys

Yibo Li et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior and processing maps of an equiatomic MoNbHfZrTi refractory high entropy alloy

Fuyu Dong et al.

INTERMETALLICS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Real-time nanoscale observation of deformation mechanisms in CrCoNi-based medium- to high-entropy alloys at cryogenic temperatures

Qingqing Ding et al.

MATERIALS TODAY (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

High-temperature deformation mechanisms and processing maps of equiatomic CoCrFeMnNi high-entropy alloy

H. T. Jeong et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of the Zener-Hollomon parameter on the dynamic recrystallization kinetics of Mg-Zn-Zr-Yb magnesium alloy

Lu Li et al.

COMPUTATIONAL MATERIALS SCIENCE (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot deformation behavior and microstructural evolution of as-quenched 7055 Al alloy fabricated by powder hot extrusion

Jian Ren et al.

MATERIALS CHARACTERIZATION (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

High impact toughness of CrCoNi medium-entropy alloy at liquid-helium temperature

Muxin Yang et al.

SCRIPTA MATERIALIA (2019)

添加到收藏夹

Article Engineering, Mechanical

A ductile fracture model considering stress state and Zener-Hollomon parameter for hot deformation of metallic materials

Xiaoqing Shang et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Utilization of hot deformation to trigger strain induced boundary migration (SIBM) in Ni-base superalloys

Joshua McCarley et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

EBSD study of microstructure evolution during axisymmetric hot compression of 304LN stainless steel

Matruprasad Rout et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Chemistry, Physical

Hot deformation behavior and processing workability of a Ni-based alloy

Zhipeng Wan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Multidisciplinary Sciences

Multicomponent intermetallic nanoparticles and superb mechanical behaviors of complex alloys

T. Yang et al.

SCIENCE (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of strain amount and strain rate on grain structure of a novel high Co nickel-based polycrystalline superalloy

Liming Tan et al.

MATERIALS & DESIGN (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Heterogeneous precipitation behavior and stacking-fault-mediated deformation in a CoCrNi-based medium-entropy alloy

Y. L. Zhao et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Multidisciplinary Sciences

Exceptional damage-tolerance of a medium-entropy alloy CrCoNi at cryogenic temperatures

Bernd Gludovatz et al.

NATURE COMMUNICATIONS (2016)

添加到收藏夹

Review Materials Science, Multidisciplinary

A review of dynamic recrystallization phenomena in metallic materials

K. Huang et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

High temperature deformation behavior and dynamic recrystallization in CoCrFeNiMn high entropy alloy

N. D. Stepanov et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Review Materials Science, Multidisciplinary

Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions

Taku Sakai et al.

PROGRESS IN MATERIALS SCIENCE (2014)

添加到收藏夹

Article Multidisciplinary Sciences

A fracture-resistant high-entropy alloy for cryogenic applications

Bernd Gludovatz et al.

SCIENCE (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Alloy Design Strategies and Future Trends in High-Entropy Alloys

Jien-Wei Yeh

JOM (2013)

添加到收藏夹

Article Nanoscience & Nanotechnology

Hot deformation behavior of austenitic stainless steel for a wide range of initial grain size

H. Mirzadeh et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

添加到收藏夹

Article Nanoscience & Nanotechnology

Dynamic behaviour of 304 stainless steel during high Z deformation

A. S. Taylor et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)

添加到收藏夹

Article Nanoscience & Nanotechnology

Correlation between Zener-Hollomon parameter and necklace DRX during hot deformation of 316 stainless steel

Meysam Jafari et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural development during hot working of Mg-3Al-1Zn

A. G. Beer et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes

JW Yeh et al.

ADVANCED ENGINEERING MATERIALS (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.