☆ 4.7 Article

Picosecond laser-textured WC-10Co4Cr metal-ceramic composite coatings with high wear resistance property

SURFACE & COATINGS TECHNOLOGY (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

The dry sliding wear rate of a Fe-based amorphous coating prepared on mild steel by HVOF thermal spraying

Hamid Al-Abboodi et al.

Summary: Wear-resistant amorphous coatings with a thickness of about 300 mm were deposited on a mild steel substrate using the HVOF thermal spray method. The hardness of the coating increased significantly after vacuum heat treatment, with the longer amorphous phase resulting in higher hardness. The coatings exhibited low porosity and excellent wear resistance, especially after heat treatment at 650 degrees C. Dry sliding wear tests showed good wear resistance of the coatings.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Chemistry, Physical

Evaluation of tribological performance for laser textured surfaces with diverse wettabilities under water/oil lubrication environments

Huixin Wang et al.

Summary: Friction and wear are important issues for engineering applications. In this study, laser-based surface treatment methods were used to modify the properties of textured surfaces, resulting in superhydrophobic surfaces with reduced friction coefficient. The surface texture, wettability, and chemistry have combined effects on the tribological performance.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Wetting Behavior of Wear-Resistant WC-Co-Cr Cermet Coatings Produced by HVOF: The Role of Chemical Composition and Surface Roughness

Pavel Komarov et al.

Summary: Superhydrophobic WC-Co-Cr cermet coatings were prepared using high velocity oxy-fuel (HVOF) spraying, with additional surface treatment by silicone oil. The study found that microstructure, phase composition, and surface topography significantly influenced the water contact angle and surface free energy of the coatings. The coatings showed good robustness in slurry abrasion response tests, indicating a need for further research on surface modifications for sacrificial applications.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Mechanical

Tribological behavior of femtosecond laser-textured leaded brass

Junyuan Huang et al.

Summary: The tribological behavior of femtosecond laser-textured leaded brass samples was studied under different surface roughness and lubrication conditions. The coefficient of friction exhibited consistent changes under various lubrication conditions, with the roughness affecting the friction coefficient. The wear mechanisms were mainly adhesive wear and abrasive wear, with differences in specific wear mechanisms observed under various friction conditions.

TRIBOLOGY INTERNATIONAL (2021)

添加到收藏夹

Article Engineering, Manufacturing

Investigation on the ablation behavior of cemented tungsten carbide by a nanosecond UV laser

Chenglong Chu et al.

Summary: The precision machining of hard and ultra-hard materials by laser beam is a key subject in modern manufacturing processes. The study shows that scanning speed and scanning times play important roles in material removal efficiency, while crack formation seems inevitable under various parameters.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Assessment of the Condition of Anilox Rollers

Arnas Savickas et al.

Summary: This study investigates the wear and cell clogging of anilox rollers in printing houses in the Baltic states, revealing that over half of the rollers are not washed properly, higher line screen rollers tend to be more clogged, and it is important to take measurements at more than three locations to assess the reliability of more worn rollers.

COATINGS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of micro-texture on wear resistance of WC/Co-based tools during cutting Ti-6Al-4V

Xiaoyan Sun et al.

Summary: This study investigated the influence of different textured directions on cutting performance by using femtosecond laser to create textures on the rake face of carbide-tipped cutting tools. Results showed that parallel textured tools could significantly reduce friction coefficient, decrease rake face wear, and improve surface roughness compared to untextured tools.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2021)

添加到收藏夹

Article Materials Science, Ceramics

Nanosecond UV laser induced subsurface damage mechanics of cemented tungsten carbide

Quanli Zhang et al.

Summary: This study investigates the subsurface damage characteristics of WC/8Co cemented carbide ablated by a nanosecond UV laser through experimental and simulation methods. The results show that thermal stress induced by high temperature gradient is one of the reasons for subsurface damage behaviors. Severe cracking and crushing behaviors are observed in the re-solidified areas and heat-affected zones.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Chemistry, Physical

Tribological performance of surface with different wettability under ball-on-disc test

Xiuqing Hao et al.

APPLIED SURFACE SCIENCE (2020)

添加到收藏夹

Article Materials Science, Ceramics

Tribological behavior and lubricating mechanism of Si3N4 in artificial seawater

Jianjun Zhang et al.

CERAMICS INTERNATIONAL (2020)

添加到收藏夹

Article Engineering, Mechanical

Tribological characteristics of a cemented carbide friction surface with chevron pattern micro-texture based on different texture density

Li Dan et al.

TRIBOLOGY INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of the Common Solvents on UV-Modified Photopolymer and EPDM Flexographic Printing Plates and Printed Ink Films

Tamara Tomasegovic et al.

COATINGS (2020)

添加到收藏夹

Article Chemistry, Physical

Controllable preparation of micro-textures on WC/Co substrate surface by an integrated laser-dry etching process for improving PVD coatings adhesion

Xuhong Guo et al.

APPLIED SURFACE SCIENCE (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Performance evaluation of HVOF sprayed WC-10Co4Cr coatings under slurry erosion

Xiao-bin Liu et al.

SURFACE ENGINEERING (2019)

添加到收藏夹

Article Optics

Analysis of energy occupying ratio of Coulomb explosion and thermal effect in picosecond pulse laser processing

Zongji Zheng et al.

OPTICS COMMUNICATIONS (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

The effect of attributes of micro-shapes of laser surface texture on the wettability of WC-CrCo metal ceramic coatings

Juan Qiao et al.

SURFACE & COATINGS TECHNOLOGY (2018)

添加到收藏夹

Article Engineering, Mechanical

Influence of Laser Pulse Number on the Ablation of Cemented Tungsten Carbides (WC-CoNi) with Different Grain Size

Shiqi Fang et al.

LUBRICANTS (2018)

添加到收藏夹

Article Automation & Control Systems

Effect of hybrid texture combining micro-pits and micro-grooves on cutting performance of WC/Co-based tools

Jialin Sun et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

添加到收藏夹

Article Engineering, Multidisciplinary

Function-oriented method for the definition and verification of microstructured surfaces

Albert Weckenmann et al.

PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY (2013)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructure and properties of Cr2O3 coating deposited by plasma spraying and dry-ice blasting

Shujuan Dong et al.

SURFACE & COATINGS TECHNOLOGY (2013)

添加到收藏夹

Article Nanoscience & Nanotechnology

Thermal stability of model Al-Li alloys after severe plastic deformation-Effect of the solute Li atoms

B. Adamczyk-Cieslak et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

添加到收藏夹

Article Engineering, Chemical

Tribochemical effects on the friction and wear behaviors of diamond-like carbon film under high relative humidity condition

H Li et al.

TRIBOLOGY LETTERS (2005)

添加到收藏夹

Article Materials Science, Multidisciplinary

Laser processing of hardmetals: Physical basics and applications

G Dumitru et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2005)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing

YH Zhao et al.

ACTA MATERIALIA (2004)

添加到收藏夹

Article Chemistry, Physical

Modified surface morphology in surface ablation of cobalt-cemented tungsten carbide with pulsed UV laser radiation

TJ Li et al.

APPLIED SURFACE SCIENCE (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.