☆ 4.7 Article

Liquid phase sintering of yttrium oxide: The effect of Al2O3 and SiO2 additives

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Ceramics

Rapidly fabricating Y2O3 transparent ceramics at low temperature by SPS with mesoporous powder

Hailiang Fang et al.

Summary: Fine-grained and highly transparent Y2O3 ceramics were successfully prepared using spark plasma sintering, and their microstructure, optical, and mechanical properties were studied. The results demonstrate the importance of the high activity of mesoporous Y2O3 in achieving high-performance ceramics at low sintering temperature.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Irradiation response of liquid-phase sintered SiC assisted with Y 2 O 3-Al 2 O 3 sintering additive at 300 & DEG;C up to 100 dpa

Bo Huang et al.

Summary: The effect of Y2O3-Al2O3 sintering additive on the irradiation response of LPS-SiC materials was investigated. CVD-SiC and LPS-SiC specimens were subjected to ion irradiation and compared. The volumetric swelling of LPS-SiC was attributed to the sintering additive YAG.

JOURNAL OF NUCLEAR MATERIALS (2023)

添加到收藏夹

Article Materials Science, Ceramics

Low-temperature joining of SiC ceramics with Y2O3-Al2O3 interlayer by SiO2-based liquid phase extrusion strategy

Sheng-Jin He et al.

Summary: By using SiO2-based liquid phase extrusion strategy with Y2O3-Al2O3-SiO2 as the filler, the joining temperature of SiC ceramics was effectively reduced to 1550 degrees Celsius.

CERAMICS INTERNATIONAL (2023)

添加到收藏夹

Article Materials Science, Ceramics

Thermodynamic and kinetic analyses of sintering in Al-doped Y2O3 nanoparticles

Kimiko Nakajima et al.

Summary: This study investigates the effects of doping on the thermodynamics and kinetics of sintering in aluminum-doped yttrium oxide nanoparticles. It demonstrates that a large dihedral angle is necessary but not sufficient for densification, and that aluminum suppresses grain boundary mobility and delays densification at intermediate stages of sintering. Additionally, it shows that at temperatures above 1150 degrees Celsius, grain growth is activated in the doped samples, leading to a higher densification rate compared to undoped samples.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

Kinetics of mullitization from sol-gel synthesized precursors

Smail Lamara et al.

Summary: The aim of this study is to investigate the formation of mullite and its kinetics using sol-gel synthesized precursors. Various techniques including thermogravimetry, differential thermal analysis, thermodilatometric analysis, and x-ray powder diffraction were employed to characterize the mullitization process. The activation energy for mullite formation was calculated and the kinetics and crystallization mechanism were determined.

JOURNAL OF THE INDIAN CHEMICAL SOCIETY (2022)

添加到收藏夹

Article Materials Science, Ceramics

Translucent yttrium oxide ceramics from low-density green bodies shaped by uniaxial pressing

A. Najafzadehkhoee et al.

Summary: This study successfully fabricated highly dense translucent Y2O3 by utilizing the high sinterability of nano Y2O3 powder, achieving high-density sintering and eliminating pores through improved particle rearrangement from low-density green bodies.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Grain growth in sintering: A discrete element model on large packings

Brayan Paredes-Goyes et al.

Summary: This translated text discusses a coupled solid-state sintering and grain growth model and its application in the study of large packings of particles within the DEM framework. Results show that even at an early stage of sintering, hardly detectable grain growth significantly affects sintering kinetics.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Materials Science, Ceramics

Fabrication and properties of macro-porous SiC using Al2O3-Y2O3-SiO2 as bonding additives

Sung Il Yun et al.

Summary: The study successfully prepared macro-porous SiC ceramics with adjustable porosity and pore size by controlling the amount of bonding additive. At different sintering temperatures, the porosity and flexural strength showed different changing patterns, while the electrical resistivity was also influenced by the components of the bonding additive.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Ceramics

Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

Zhongchao Fu et al.

Summary: An easy and effective deionization suspension treatment was used to alleviate the hydrolysis issue of Y2O3 powder, resulting in fine-grained and highly transparent Y2O3 ceramics without the use of sintering additives. The use of centrifugal casting method improved the homogeneity of green bodies, leading to fully dense Y2O3 transparent ceramics with in-line transmittance close to theoretical values.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Ceramics

Joining of Cf/SiC composites and Si3N4 ceramic with Y2O3-Al2O3-SiO2 glass filler for high-temperature applications

Liangbo Sun et al.

Summary: This study investigated the joining of Cf/SiC and Si3N4 using glass and identified direct bonding as the main interfacial bonding mechanism. The joint showed a maximum shear strength of -34 MPa and remained at -13 MPa after thermal shock for 10 cycles. Bubbles in the glass filler were found to be the main factor causing degradation of joint performance. Improving the high temperature resistance of joining materials is suggested for application of this joint structure.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Translucent γ-AlOOH and γ-Al2O3 glass-ceramics using the cold sintering process

Thomas Herisson de Beauvoir et al.

Summary: The Cold Sintering Process was used to promote in situ reactive sintering of hydroxide precursors Al(OH)3, xH2O. The result was dense translucent pellets containing a mix of amorphous and crystalline phases. Further heat treatment induced the transformation of boehmite into gamma-Al2O3, demonstrating the possibility of producing optically translucent ceramics with low temperature stability.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Materials Science, Ceramics

Preparation and study of the mechanical and optical properties of infrared transparent Y2O3-MgO composite ceramics

Zongyun Shen et al.

Summary: Y2O3-MgO composite ceramics were synthesized and the effects of pre-sintering temperature on the microstructural, mechanical, and optical properties were investigated. The ceramics showed increased grain size, decreased hardness and fracture toughness with higher pre-sintering temperatures. The maximum fracture toughness achieved was 1.42 MPa m(1/2) with a Vickers hardness of 10.4 GPa, and varying transmittance levels were observed at different sintering temperatures.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot pressing of Yb:Y2O3 laser ceramics with LiF sintering aid

Stanislav Balabanov et al.

Summary: Transparent ytterbium doped yttria ceramics were fabricated using hot uniaxial pressing in vacuum and two-stage Hot Isostatic Pressing, with nanopowders obtained through self-propagating high-temperature synthesis with lithium fluoride as a sintering aid. The addition of LiF during powder synthesis changed powder morphology and reduced carbon contamination in ceramics, while also promoting sintering.

OPTICAL MATERIALS (2021)

添加到收藏夹

Article Materials Science, Ceramics

Crystallization behavior and IR structure of yttrium aluminosilicate glasses

Qingshuang Zheng et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Mechanical properties and thermal conductivity of dense β-SiAlON ceramics fabricated by two-stage spark plasma sintering with Al2O3-AlN-Y2O3 additives

Y. L. Lan et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Fabrication of Er:Y2O3 transparent ceramics for 2.7 μm mid-infrared solid-state lasers

Danlei Yin et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

The effect of yttrium nitrate addition on the densification behaviour of Y2O3 ceramics during the cold sintering process

Doyun Lee et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Thermodynamics and kinetics of sintering of Y2O3

Kimiko Nakajima et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

A new method for the preparation of transparent Y2O3 nanocrystalline ceramic with an average grain size of 20 nm

Zhangyi Huang et al.

SCRIPTA MATERIALIA (2020)

添加到收藏夹

Article Materials Science, Ceramics

Original Article Doping effect on the flash sintering of Y2O3: Promotion of densification and optical translucency

Hidehiro Yoshida et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Two-step sintering behavior of titanium-doped Y2O3 ceramics with monodispersed sub-micrometer powder

Wook Ki Jung et al.

CERAMICS INTERNATIONAL (2019)

添加到收藏夹

Article Materials Science, Ceramics

High-temperature stable inverse opal photonic crystals via mullite-sol-gel infiltration of direct photonic crystals

Priscila Bueno et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Strategies and practices for suppressing abnormal grain growth during liquid phase sintering

John G. Fisher et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Materials Science, Ceramics

Microstructural freezing of highly NIR transparent Y2O3-MgO nanocomposite via pressure-assisted two-step sintering

Ho Jin Ma et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fabrication of Y2O3 transparent ceramics by hot isostatic pressing from precipitated nanopowders

Xinyou Huang et al.

OPTICAL MATERIALS (2019)

添加到收藏夹

Article Materials Science, Ceramics

Liquid phase sintering and characterization of SiC ceramics

A. C. Santos et al.

CERAMICS INTERNATIONAL (2018)

添加到收藏夹

Article Materials Science, Ceramics

A critique of master sintering curve analysis

T. Frueh et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Yb:Y2O3 transparent ceramics processed with hot isostatic pressing

Jun Wang et al.

OPTICAL MATERIALS (2017)

添加到收藏夹

Article Materials Science, Ceramics

First-principles study of structural, mechanical, and thermodynamic properties of cubic Y2O3 under high pressure

Xian Zhang et al.

CERAMICS INTERNATIONAL (2017)

添加到收藏夹

Article Materials Science, Ceramics

High optical quality Y2O3 transparent ceramics with fine grain size fabricated by low temperature air pre-sintering and post-HIP treatment

Zhongying Wang et al.

CERAMICS INTERNATIONAL (2016)

添加到收藏夹

Article Engineering, Electrical & Electronic

Basic and Peculiar Properties of Chromium-Magnesium Co-Doped YAS-Based Optical Fibers

Alexander V. Kir'yanov et al.

IEEE JOURNAL OF QUANTUM ELECTRONICS (2016)

添加到收藏夹

Article Materials Science, Ceramics

Tailoring Ca3Co4O9 microstructure and performances using a transient liquid phase sintering additive

A. Sotelo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

A reversible wetting transition in strontium titanate and its influence on grain growth and the grain boundary mobility

Wolfgang Rheinheimer et al.

ACTA MATERIALIA (2015)

添加到收藏夹

Article Engineering, Electrical & Electronic

Distribution of Bismuth and Bismuth-Related Centers in Core Area of Y-Al-SiO2:Bi Fibers

Alexander V. Kir'yanov et al.

JOURNAL OF LIGHTWAVE TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Ceramics

Structural and Thermo-Mechanical Properties of Nd: Y2O3 Transparent Ceramics

Lei Zhang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2015)

添加到收藏夹

Article Materials Science, Ceramics

Two-stage master sintering curve applied to two-step sintering of oxide ceramics

Vaclav Pouchly et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ceramic laser materials: Past and present

Jasbinder Sanghera et al.

OPTICAL MATERIALS (2013)

添加到收藏夹

Article Optics

Novel transparent ceramics for solid-state lasers

Hao Yang et al.

HIGH POWER LASER SCIENCE AND ENGINEERING (2013)

添加到收藏夹

Article Optics

Effect of Nd concentration on structural and optical properties of Nd:Y2O3 transparent ceramic

Xiaorui Hou et al.

JOURNAL OF LUMINESCENCE (2011)

添加到收藏夹

Article Chemistry, Physical

Thermodynamic Evaluation of the Si-C-Al-Y-O System for LPS-SiC Application

Zhu Pan et al.

JOURNAL OF PHASE EQUILIBRIA AND DIFFUSION (2010)

添加到收藏夹

Review Materials Science, Ceramics

Review of mullite synthesis routes by sol-gel method

Luciana S. Cividanes et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2010)

添加到收藏夹

Article Materials Science, Ceramics

Effect of Europium Concentration on Densification of Transparent Eu:Y2O3 Scintillator Ceramics Using Hot Pressing

Stephen R. Podowitz et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2010)

添加到收藏夹

Article Materials Science, Ceramics

ZrO2-doped Y2O3 transparent ceramics via slip casting and vacuum sintering

Lingling Jin et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2010)

添加到收藏夹

Article Materials Science, Ceramics

Master Sintering Curve - A Practical Approach to its Construction

V. Pouchly et al.

SCIENCE OF SINTERING (2010)

添加到收藏夹

Review Materials Science, Multidisciplinary

Review: liquid phase sintering

Randall M. German et al.

JOURNAL OF MATERIALS SCIENCE (2009)

添加到收藏夹

Article Materials Science, Ceramics

Sintering of Yb3+:Y2O3 transparent ceramics in hydrogen atmosphere

Jian Zhang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanism of the liquid-phase sintering for Nd:YAG ceramics

R. Boulesteix et al.

OPTICAL MATERIALS (2009)

添加到收藏夹

Article Materials Science, Ceramics

Low temperature sintering of polycrystalline yttria by transition metal ion doping

Masayasu Kodo et al.

JOURNAL OF THE CERAMIC SOCIETY OF JAPAN (2009)

添加到收藏夹

Article Thermodynamics

Thermodynamic reassessment of the Y2O3-Al2O3-SiO2 system and its subsystems

Huahai Mao et al.

CALPHAD-COMPUTER COUPLING OF PHASE DIAGRAMS AND THERMOCHEMISTRY (2008)

添加到收藏夹

Article Materials Science, Ceramics

Fabrication, optical transmittance, and hardness of IR-transparent ceramics made from nanophase yttria

Hergen Eilers

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2007)

添加到收藏夹

Article Materials Science, Ceramics

Two-step sintering of ceramics with constant grain-size, I.: Y2O3

XH Wang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Crystallization of lanthanum and yttrium aluminosilicate glasses

N Sadiki et al.

JOURNAL OF NUCLEAR MATERIALS (2006)

添加到收藏夹

Article Thermodynamics

Aluminosilicate formation in various mixtures of tetra ethyl orthosilicate (TEOS) and aluminum nitrate (ANN)

AK Chakraborty

THERMOCHIMICA ACTA (2005)

添加到收藏夹

Article Materials Science, Multidisciplinary

Formation of intergranular amorphous films during the microstructural development of liquid phase sintered silicon carbide ceramics

E Volz et al.

JOURNAL OF MATERIALS SCIENCE (2004)

添加到收藏夹

Article

Viscosity of nitrogen containing Y2O3-Al2O3-SiO2 melts and hardness of glasses

N Saito et al.

JOURNAL OF THE JAPAN INSTITUTE OF METALS (2003)

添加到收藏夹

Article Physics, Applied

Yb3+:Y2O3 ceramics -: a novel solid-state laser material

JR Lu et al.

JAPANESE JOURNAL OF APPLIED PHYSICS PART 2-LETTERS & EXPRESS LETTERS (2002)

添加到收藏夹

Article Materials Science, Ceramics

Crystallization kinetics of mullite from Al2O3-SiO2 glasses under non-isothermal conditions

T Takei et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2001)

添加到收藏夹

Article Materials Science, Ceramics

Liquid-phase sintering of PZT ceramics

DL Corker et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.