☆ 4.6 Article

Enhanced corrosion resistance of Mg17Al12 compounds by Ce modification

VACUUM (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Nanoscience & Nanotechnology

Effect of calcium addition on the microstructure, mechanical properties, and corrosion behavior of AZ61-Nd alloy

Zhechao Zhang et al.

Summary: The effects of calcium (Ca) on the microstructure, mechanical properties and corrosion behavior of extruded AZ61-1Nd-xCa (x = 0, 0.5, 1, 2 wt.%) alloys were studied. The addition of calcium increased the volume fraction of Al2Ca precipitates and refined the grain size. The alloys showed consistent tensile strength and increased hardness with increasing calcium content. However, the presence of Al-Nd and brittle Al2Ca phases significantly reduced the elongation. The corrosion resistance of AZ61-1Nd alloy was greatly improved with the addition of 1 wt.% calcium due to the uniformly distributed Al2Ca acting as a physical barrier. The obtained AZ61-1Nd-1Ca alloy with moderate strength and low corrosion rate is considered a candidate material for marine applications.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of solute redistribution during heat treatment on micro-galvanic corrosion behavior of dilute Mg-Al-Ca-Mn alloy

Kai Zhang et al.

Summary: The underlying mechanism of solute redistribution during heat treatment in affecting corrosion behavior of Mg-1.19Al-0.28Ca-0.44Mn (wt%) alloy was systematically clarified. The supersaturated Al and Ca solutes in matrix effectively alleviate the driving force of micro-galvanic corrosion caused by Al-Mn phases, based on positive shift of matrix potential and film densification. After aging treatment, monoatomic-layer G.P. zones realize higher strength and better corrosion resistance of alloy as compared to nanosized Al2Ca, due to higher number density and less solute consumption in matrix.

CORROSION SCIENCE (2023)

添加到收藏夹

Article Chemistry, Physical

B2-structured Fe3Al alloy manufactured by laser powder bed fusion: Processing, microstructure and mechanical performance

A. M. Vilardell et al.

Summary: Prealloyed Fe3Al with high density, good surface quality, and suitable mechanical properties was successfully manufactured using laser powder bed fusion. The presence of minor variations in aluminum content along the melt pool and the development of a weak texture along the building direction were observed in the microstructure. The mechanical properties were found to be temperature-dependent, with a significant loss in strength at higher temperatures due to plastic deformation and tribochemical wear.

INTERMETALLICS (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Structure and properties of TiNi shape memory alloy after low-temperature ECAP in shells

R. Karelin et al.

Summary: The effect of low-temperature equal-channel angular pressing (ECAP) on the structure formation and mechanical and functional properties of a near-equiatomic titanium nickelide (TiNi) shape memory alloy in shells is studied. ECAP with channel intersection angles of 120° and 110° is conducted at temperatures ranging from 20°C to 330°C after 1 pass. Pure iron is determined as the optimum material for shells as it remains undamaged after ECAP at room temperature. The optimal deformation temperature for ECAP in a shell is found to be 200°C. Deformation at low temperatures leads to the premature destruction of TiNi samples. ECAP of the TiNi core in a shell at 200°C after 1 pass results in the formation of an elongated, banded martensite structure with a bandwidth of approximately 100 nm. The best combination of mechanical and functional properties is achieved after ECAP of a TiNi sample with a diameter of 12 mm in core-shell mode at 200°C, followed by post-deformation annealing at 400°C for 1 hour.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of a novel polycrystalline Ni3Al-based intermetallic alloy

Yihan Zhao et al.

Summary: A polycrystalline Ni3Al-based intermetallic alloy was successfully prepared via vacuum induction melting processing. The microstructural evolution and mechanical properties of the alloy were studied through solution treatments at different temperatures. The results showed changes in the size and morphology of the gamma ' phase after treatment and the precipitation of secondary gamma ' phase. The alloy exhibited high room temperature yield strength and tensile strength, and the presence of alpha-Cr particles improved its high-temperature creep performance.

INTERMETALLICS (2023)

添加到收藏夹

Review Chemistry, Physical

Energy damping in shape memory alloys: A review

Soheil Saedi et al.

Summary: Shape memory alloys (SMAs) have attracted significant attention as potential damping device materials in recent years. This article provides a comprehensive review of the damping characteristics of SMAs and the experimental methods used to characterize their damping properties. The shape memory response and associated damping quality of Fe-based, Cu-based, and NiTi-based alloys, including their behaviors and limitations, are discussed. The review also highlights the important parameters that impact SMA damping behavior, which need to be investigated by researchers and manufacturers to address current design challenges.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of boron, Hf and Ta content on boride morphology and microstructure of & beta;-solidified & gamma;-TiAl alloys

Kaige Wang et al.

Summary: In this study, the effects of boron, Hf, and Ta content on the boride morphology and microstructure of a ?-TiAl alloy were investigated. Increasing boron content leads to a transition in boride morphology from flat to curved. Addition of Hf also causes a transition in boride morphology from flat to curved, while addition of Ta results in smaller borides with dendritic morphology. The combination of solid solution strengthening, precipitation strengthening, and grain refinement contributes to the increased hardness of the alloy. The study also suggests that the addition of Ta can refine the size of borides and potentially improve the room temperature properties of the ?-TiAl alloy.

VACUUM (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation of the composition, structure and magnetic properties of the Nd2Fe14B ceramics dependence on the initial powder characteristics and spark plasma sintering modes

V. Yu Samardak et al.

Summary: In this study, the influence of pulse current frequency on the structure, composition, and magnetic properties of Nd2Fe14B magnetic ceramics was investigated using SEM, TEM, EDS and XRD methods. The results showed that the morphology, structure and composition of the initial Nd2Fe14B powder had a significant impact on the magnetization saturation value and coercive force.

VACUUM (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of oxalic acid on the corrosion behavior of AZ91D magnesium alloy in deionized water

Sisi Liu et al.

Summary: Due to its light weight, Mg alloy can be applied to automotive engines and cooling systems to reduce vehicle weight, energy consumption and exhaust pollution. However, ethylene glycol-type coolants can be oxidized into oxalic acid, glyoxylic acid and other substances at high temperature, which can cause the damage of Mg alloy. In this paper, electrochemical methods, hydrogen evolution and surface analysis methods were used to study the influence of oxalic acid on the corrosion behavior of AZ91D magnesium alloy in deionized water. The results indicated that the oxalic acid accelerated the corrosion of Mg alloy, and its corrosion rate increased with the concentration of oxalic acid. However, interestingly, the corrosion rate of Mg alloy in oxalic acid solution slowed as the immersed time lengthened, which could be related to the accumulation of corrosion products and the consumption of hydrogen ions. The main corrosion product of the corrosion of Mg alloy in oxalic acid solution was composed of magnesium oxalate.

VACUUM (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of extrusion on the microstructure and corrosion behavior of Mg-Zn-Mn-(0,1.5)Sr alloys in Hank's solution

Li Lei et al.

Summary: The microstructure, corrosion behavior, and cytocompatibility of as-cast and extruded Mg-Zn-Mn-(0, 1.5)Sr alloys in Hank's solution were investigated. Extrusion resulted in grain refinement and preferred texture, while distinct features of Sr-free and Sr-containing alloys included an increase in dislocation density and fragmentation of Mg17Sr2, respectively. Extrusion significantly accelerated the corrosion rate of Sr-free alloy, while alloyed Sr eliminated this deterioration process. Sr alloying decreased the corrosion rate and enhanced the cytocompatibility of the extruded Mg-Zn-Mn alloy without affecting the corrosion penetration depth, demonstrating the superiority of Sr alloying for extruded magnesium alloys as implant materials.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Cu content on electrical resistivity, mechanical properties and corrosion resistance of AlCuxNiTiZr0.75 high entropy alloy films

Kai Huang et al.

Summary: The AlCuxNiTiZr0.75 high entropy alloy films were successfully deposited by magnetron sputtering with controlled copper content, resulting in decreased resistivity while maintaining mechanical properties and corrosion resistance. The increase of copper content altered the electronic structure of the films, leading to a sharp decrease in resistivity to 66 μΩ·cm at x = 1.4. The hardness-to-elastic modulus ratio peaked at x = 1.4, indicating enhanced ductility, while corrosion resistance remained good with low corrosion current densities in a 3.5 wt% NaCl solution.

VACUUM (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion behavior of AZ31 magnesium alloy with calcium addition

Umer Masood Chaudry et al.

Summary: The effect of calcium on the microstructure and corrosion characteristics of AZ31 was investigated. It was found that the formation of (Mg, Al)(2)Ca in AZ31-0.5Ca contributed to improved corrosion resistance.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced mechanical behavior and corrosion resistance of AZ31 magnesium alloy through a novel solid-phase processing

V. Beura et al.

Summary: In this study, a novel solid-phase processing technique called shear assisted processing and extrusion (ShAPE) was used to modify the microstructure of AZ31 magnesium alloy, resulting in improved corrosion resistance and mechanical properties compared to wrought AZ31 alloys. ShAPE processing led to a refined grain structure, homogenized second phase distribution, and reduced residual strain in the matrix, which contributed to improved corrosion resistance. Additionally, a tilted basal texture along the ShAPE processed direction contributed to enhanced ductility and eliminated tension-compression asymmetry.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of solid solution Zn atoms on corrosion behaviors of Mg-2Nd-2Zn alloys

Lingxiong Sun et al.

Summary: The effects of heat treatments on the microstructures and corrosion behaviors of extruded Mg-2Nd-2Zn alloys were investigated. It was found that the solid solution treatment significantly reduced the corrosion rate of Mg alloys.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of 2,6-dihydroxybenzoic acid on the corrosion behavior and discharge performance of AZ31 Mg alloy

Rongrong Xu et al.

Summary: This study investigates the influence of 2,6-dihydroxybenzoic acid on the corrosion performance and discharge properties of AZ31 Mg alloy. The results show that low concentration of this compound enhances the corrosion resistance of Mg alloy, while high concentration leads to a deterioration in corrosion performance. Additionally, the presence of 2,6-dihydroxybenzoic acid greatly modifies the discharge properties of the Mg anode.

VACUUM (2022)

添加到收藏夹

Article Engineering, Multidisciplinary

An intelligent Mg anode for protection of the concrete-covered steel tubing in carbon capture and storage

Peng-Peng Wu et al.

Summary: This paper investigates the use of Mg as an intelligent anode in underground Carbon Capture and Storage (CCS) projects to detect the carbonation level of concrete and protect the steel casing. The results showed that Mg was more sensitive to carbonation and could act as a smart anode in carbonated simulated concrete pore solutions (SCPSs).

COMPOSITES PART B-ENGINEERING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

La containing Mg alloy for enhanced corrosion at elevated temperatures in ethylene glycol media

A. Prasad et al.

Summary: A novel Mg alloy (Mg-10Dy-0.7La) with an excellent combination of corrosion and mechanical properties at room temperature was investigated for its high-temperature corrosion behavior in ethylene glycol. The results showed that the Mg-10Dy-0.7La alloy exhibited significantly enhanced corrosion resistance compared to the commonly used AZ91 Mg alloy, attributed to higher activation energy and enhanced concentration of oxides in the former.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Chemistry, Physical

Anisotropy investigation of an ECAP-processed Mg-Al-Ca-Mn alloy with synergistically enhanced mechanical properties and corrosion resistance

Chao Sun et al.

Summary: This study investigated the anisotropy of a 32-pass ECAP processed Mg-3.7Al-1.8Ca-0.4Mn alloy, which exhibited synergistically enhanced mechanical properties and corrosion resistance. The ECAP alloy had homogeneous fine alpha-Mg grains and different distribution of refined Al2Ca particles. The refinement of microstructure resulted in the formation of a protective film on the ECAP alloy, leading to different corrosion mechanisms compared to the as-cast alloy. The distribution of Al2Ca and the texture of alpha-Mg were identified as the main factors affecting the anisotropic properties of the ECAP alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Physics, Applied

A step-by-step guide to perform x-ray photoelectron spectroscopy

Grzegorz Greczynski et al.

Summary: There is a growing concern within the surface science community regarding the decline in work quality and meaningless chemical bond assignment in XPS articles. This trend could have disastrous consequences for scientific research. To address this, a comprehensive tutorial is offered, providing a step-by-step guide for experimental planning, data acquisition, spectra analysis, and results presentation, with a focus on improving the quality and reliability of XPS data analysis. The tutorial aims to broaden the application of XPS and enhance practitioners' ability to draw meaningful insights from XPS analysis.

JOURNAL OF APPLIED PHYSICS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Simultaneously enhanced the strength and ductility in Mg17Al12 intermetallic compound with Ce addition

Baosheng Liu et al.

Summary: The novel Mg17Al12-3Ce alloy, fabricated by addition appropriate Ce, demonstrates significantly enhanced compressive properties compared to Mg17Al12 compound, primarily attributed to refined grains, reduced wetting grain boundaries, and precipitation of Al11Ce3 phase.

MATERIALS LETTERS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

Mei-Xuan Li et al.

Summary: The effect of trace Ce addition on the microstructure evolution and corrosion behavior of dilute Mg-0.6Al-0.5Mn-0.25Ca alloys has been investigated. The addition of Ce resulted in the formation of less noble Al8Mn4Ce and Al11Ce3 phases. Notably, the alloy containing 0.3 wt% Ce exhibited the lowest corrosion rate, attributed to factors such as the low potential difference, compact composite oxide film, and enrichment of Fe.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of novel heat-resistant Al-12Ce-xCu-yMg alloy under laser melting

Yu Wang et al.

Summary: In this study, novel Al-Ce alloys were designed using laser melting, and their microstructure and high-temperature mechanical properties were investigated. The results showed that the addition of Cu can refine the primary phase of the alloys, while Mg mainly contributes to solid solution strengthening. The addition of Cu and Mg significantly improves the room temperature mechanical properties of the eutectic Al-Ce alloys.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Chemistry, Physical

Novel Mg-Al-Sn-Ca with enhanced mechanical properties and high corrosion rate via sub-rapid solidification for degradable magnesium alloy

Dawei Wang et al.

Summary: This study utilizes sub-rapid solidification (SRS) to modify the microstructure, particularly the eutectic phase, of Mg-4.5Al-1.5Sn-0.5Ca alloy. The SRS alloy exhibits superior strength-ductility synergy and increased corrosion rates compared to the conventional solidification alloy. This work proposes a novel degradable magnesium alloy and a processing method for its preparation.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Zn addition on the corrosion behaviours of as-cast BCC Mg-11Li based alloys in NaCl solution

Chuanqiang Li et al.

Summary: The effect of zinc on the corrosion behaviors of Mg-11Li-xZn alloys in NaCl solution was investigated. The results showed that the corrosion resistance of the alloys increased with the increase of zinc content. Filiform-like corrosion occurred at the early stage, and pitting corrosion appeared in some alloys with immersion time. Small amounts of zinc could reduce the corrosion rate, while excessive zinc accelerated the corrosion.

MATERIALS & DESIGN (2022)

添加到收藏夹

Article Multidisciplinary Sciences

Towards development of a high-strength stainless Mg alloy with Al-assisted growth of passive film

Qingchun Zhu et al.

Summary: The authors have developed a high-strength magnesium alloy with significantly improved mechanical properties and corrosion resistance. The alloy features a low corrosion rate, high yield strength, and moderate tensile elongation, making it competitive compared to other magnesium alloys. The development of a thin and dense protective film and refinement of grains contribute to the high strength and good ductility of the alloy. These findings are expected to inspire the design of next-generation high-performance magnesium alloys.

NATURE COMMUNICATIONS (2022)

添加到收藏夹

Article Chemistry, Physical

Mg17Al12 intermetallic modified with Yttrium additions

K. Korgiopoulos et al.

Summary: This study investigates the effect of Yttrium on Mg17Al12, finding that low and high Y additions can respectively decrease and increase its lattice constant, leading to complex influences on its mechanical properties.

INTERMETALLICS (2021)

添加到收藏夹

Article Chemistry, Physical

Effects of Zr and Co on the microstructure and mechanical properties of NiAl-based alloys

Dongjun Wang et al.

Summary: By optimizing the composition of the alloy and adding elements Zr and Co, the mechanical properties of the NiAl-Cr(Mo) alloy can be significantly improved, especially in terms of compressive strength and plasticity.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Research on the high temperature oxidation mechanism of Cr3C2-NiCrCoMo coating for surface remanufacturing

Ji-yu Du et al.

Summary: A novel Cr3C2-NiCrCoMo (NCC) coating with modified multielement alloy adhesive phase was developed to improve the high-temperature oxidation performance of remanufactured coatings. The synergistic effect of multiple alloying phases on the oxidation resistance of coating was explored, showing that NCC coatings have lower oxidation rate, remarkable oxidation resistance, and preferable interface matching between the oxide scale and the coating. The enhanced oxidation resistance is attributed to the formation of multicomponent composite oxide scales within NCC coatings.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Self-generating construction of applicable corrosion-resistant surface structure of magnesium alloy

Ming Yin et al.

Summary: A double-layer protective film of Mg-In alloy was constructed and adjusted by controlling the amount of indium (In) addition, significantly enhancing the corrosion resistance of the alloy. The improved corrosion layer structure exhibited a self-generated function during the self-corrosion deposition process.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

The corrosion of Al-supersaturated Mg matrix and the galvanic effect of secondary phase nanoparticles

Peng-Peng Wu et al.

Summary: Research on Al-supersaturated Mg alloys found that the presence of supersaturated Al helps in forming a protective surface and effectively suppresses micro-galvanic corrosion, while secondary phase nano-particles do not have a significant deteriorating effect on corrosion.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mg17Al12 phase refinement and the improved mechanical performance of Mg?6Al alloy with trace erbium addition

K. Korgiopoulos et al.

Summary: The study demonstrates that the mechanical properties of Mg-6wt% Al casting alloy can be significantly improved by adding low levels of Er, due to the modifying effect of Er on Mg17Al12 precipitates and α-Mg. The presence of Er influences the formation temperature of Al2Er Laves, affecting the inoculating effect of the alloy.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced mechanical properties and corrosion resistance of rolled Mg-1.5Sn-0.5Ca alloy by Ce microalloying

Chunming Wang et al.

Summary: The addition of minor cerium refines the microstructure, enhances the strength and ductility of the alloy, and improves its corrosion resistance.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Multidisciplinary Sciences

The same chemical state of carbon gives rise to two peaks in X-ray photoelectron spectroscopy

G. Greczynski et al.

Summary: Chemical state analysis in X-ray photoelectron spectroscopy (XPS) relies on assigning well-defined binding energy values to core level electrons originating from atoms in particular bonding configurations. Here, direct evidence is presented for the violation of this paradigm, as the C 1s peak due to C-C/C-H bonded atoms from adventitious carbon (AdC) layers splits into two distinctly different contributions. This finding exposes fundamental problems with the reliability of reported XPS data and suggests discontinuing the use of adventitious carbon in XPS.

SCIENTIFIC REPORTS (2021)

添加到收藏夹

Article Chemistry, Physical

Polyetherimide-LaNi5 composite films for hydrogen storage applications

Gabriel Rodrigues de Almeida Neto et al.

Summary: This study investigated the preparation of PEI-LaNi5 composite films for hydrogen storage, demonstrating that PEI films filled with LaNi5 are promising materials for this purpose. The membranes were successfully produced through solvent casting assisted by an ultrasonic bath, and the results showed that the film morphology remained unchanged after hydrogenation cycles.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

X-ray photoelectron spectroscopy: Towards reliable binding energy referencing

G. Greczynski et al.

PROGRESS IN MATERIALS SCIENCE (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Corrosion behavior of a self-sealing coating containing CeO2 particles on pure Mg produced by micro-arc oxidation

Zhongren Zheng et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

The role of the beta-Mg17Al12 phase on the anomalous hydrogen evolution and anodic dissolution of AZ magnesium alloys

C. Ubeda et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Physics, Multidisciplinary

The Formation of the ω Phase in the Titanium-iron System under Shear Deformation

B. B. Straumal et al.

JETP LETTERS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of 0.3 wt% oxygen on mechanical properties of a TiZrAl alloy prepared by vacuum arc melting

X. J. Jiang et al.

VACUUM (2020)

添加到收藏夹

Article Chemistry, Physical

Assessing phase equilibria and atomic mobility of intermetallic compounds in aluminum-magnesium alloy system

Renhai Shi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and mechanical behavior of in situ TiC reinforced Fe3Al (Fe-23Al-3Cr)matrix composites by mechanical alloying and vacuum hot-pressing sintering technology

Xinghua Zhang et al.

VACUUM (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of V addition on the solidification microstructures and room temperature compression properties of NiAl-Cr(Mo) hypereutectic alloy

Zhao Shang et al.

VACUUM (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Bulk and Surface Low Temperature Phase Transitions in the Mg-Alloy EZ33A

Alexander Straumal et al.

METALS (2020)

添加到收藏夹

Review Metallurgy & Metallurgical Engineering

Review of Mg alloy corrosion rates

Andrej Atrens et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2020)

添加到收藏夹

Article Chemistry, Physical

Study on the effect of mischmetal (La,Ce) on the micro-galvanic corrosion of AZ91 alloy using multiscale methods

Ruilin Jia et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

The microstructure, mechanical properties and corrosion behaviour of Ce-containing Mg-3Sn-1Ca alloy

Liu Yang et al.

MATERIALS SCIENCE AND TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Ce and Y on Modification and Corrosion Behavior of Mg-0.8% Si Alloy: A Correlation Study

Shuai Han et al.

CORROSION (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of mixed rare earth elements(Y and Ce) on the microstructure and corrosion behaviour of Mg-4Al-3Ca alloy

Yun Chen et al.

MATERIALS RESEARCH EXPRESS (2019)

添加到收藏夹

Article Chemistry, Physical

Reliable determination of chemical state in x-ray photoelectron spectroscopy based on sample-work-function referencing to adventitious carbon: Resolving the myth of apparent constant binding energy of the C 1s peak

G. Greczynski et al.

APPLIED SURFACE SCIENCE (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Plastic deformation behavior and operative slip systems in Mg17Al12 single crystals

Koji Hagihara et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Multidisciplinary Sciences

Turning a native or corroded Mg alloy surface into an anti-corrosion coating in excited CO2

Yuecun Wang et al.

NATURE COMMUNICATIONS (2018)

添加到收藏夹

Article Chemistry, Physical

Prominent role of a high volume fraction of Mg17Al12 particles on tensile behaviors of rolled Mg-Al-Zn alloys

Min Zha et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Structure and magnetic properties of SmCo5/X (X=Fe, Fe-Co, Co) magnetic bilayer films on MgO(110) substrate

Ataru Suzuki et al.

JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Scheil-Gulliver Constituent Diagrams

Arthur D. Pelton et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)

添加到收藏夹

Article Chemistry, Physical

C1s Peak of Adventitious Carbon Aligns to the Vacuum Level: Dire Consequences for Material's Bonding Assignment by Photoelectron Spectroscopy

Grzegorz Greczynski et al.

CHEMPHYSCHEM (2017)

添加到收藏夹

Article Chemistry, Physical

Corrosion product layers on magnesium alloys AZ31 and AZ61: Surface chemistry and protective ability

S. Feliu et al.

APPLIED SURFACE SCIENCE (2015)

添加到收藏夹

Article Chemistry, Physical

Effect of erbium modification on the microstructure, mechanical and corrosion characteristics of binary Mg-Al alloys

Sankaranarayanan Seetharaman et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

添加到收藏夹

Article Chemistry, Physical

The formation of intermetallic compounds during interdiffusion of Mg-Al/Mg-Ce diffusion couples

Jiahong Dai et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

添加到收藏夹

Article Nanoscience & Nanotechnology

Role of Al modification on the microstructure and mechanical properties of as-cast Mg-6Ce alloys

Zhongtao Jiang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Article Chemistry, Physical

A high-specific-strength and corrosion-resistant magnesium alloy

Wanqiang Xu et al.

NATURE MATERIALS (2015)

添加到收藏夹

Article Chemistry, Physical

Influences of alloying elements and oxygen on the stability and elastic properties of Mg17Al12

Jianhong Dai et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

添加到收藏夹

Article Chemistry, Applied

Effect of erbium on microstructures and properties of Mg-Al intermetallic

Li Yonggang et al.

JOURNAL OF RARE EARTHS (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of native point defect thermodynamics on off-stoichiometry in β-Mg17Al12

Dongwon Shin et al.

ACTA MATERIALIA (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

The role of strontium in modifying aluminium-silicon alloys

M. Timpel et al.

ACTA MATERIALIA (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Nd on the corrosion behaviour of AM50 and AZ91D magnesium alloys in 3.5 wt.% NaCl solution

R. Arrabal et al.

CORROSION SCIENCE (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of cerium additions on the corrosion behaviour of high pressure die cast AM50 alloy

Faruk Mert et al.

CORROSION SCIENCE (2012)

添加到收藏夹

Article Chemistry, Physical

Re-determination of γ/(γ plus α-Mg) phase boundary and experimental evidence of R intermetallic compound existing at lower temperatures in the Mg-Al binary system

Y. P. Ren et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2012)

添加到收藏夹

Article Nanoscience & Nanotechnology

The effect of oxygen and stress state on the yield behavior of commercially pure titanium

M. C. Brandes et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

添加到收藏夹

Article Chemistry, Physical

Effect of Ce on microstructure, mechanical properties and corrosion behavior of high-pressure die-cast Mg-4Al-based alloy

Jinghuai Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2011)

添加到收藏夹

Article Chemistry, Physical

XPS study of the surface chemistry on AZ31 and AZ91 magnesium alloys in dilute NaCl solution

Lei Wang et al.

APPLIED SURFACE SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion behaviour of AM60 magnesium alloys containing Ce or La under thin electrolyte layers. Part 2: Corrosion product and characterization

Wenjuan Liu et al.

CORROSION SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion behavior of equal-channel-angular-pressed pure magnesium in NaCl aqueous solution

Dan Song et al.

CORROSION SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Oxygen on the Microstructure of Ti47Al0.7B Alloys

Yingche Ma et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of rare earth element Ce and La on corrosion behavior of AM60 magnesium alloy

Wenjuan Liu et al.

CORROSION SCIENCE (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

A first quantitative XPS study of the surface films formed, by exposure to water, on Mg and on the Mg-Al intermetallics: Al3Mg2 and Mg17Al12

Ming Liu et al.

CORROSION SCIENCE (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of the β-phase morphology on the corrosion of the Mg alloy AZ91

Ming-Chun Zhao et al.

CORROSION SCIENCE (2008)

添加到收藏夹

Article Nanoscience & Nanotechnology

Micro structures, tensile properties and corrosion behavior of die-cast Mg-4Al-based alloys containing La and/or Ce

Jinghuai Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of combinative addition of strontium and rare earth elements on corrosion resistance of AZ91D magnesium alloy

Niu Jie-xin et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Improvement of corrosion resistance of AZ91D magnesium alloy by holmium addition

Zhou Xuehua et al.

CORROSION SCIENCE (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fabrication of lotus-type porous Ni3Al with and without boron

Takuya Ide et al.

MATERIALS TRANSACTIONS (2006)

添加到收藏夹

Article Thermodynamics

FactSage thermochemical software and databases

C Bale et al.

CALPHAD-COMPUTER COUPLING OF PHASE DIAGRAMS AND THERMOCHEMISTRY (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.