☆ 4.7 Article

Numerical investigation of a thermoelectric generator system with embedded sickle-shaped fins

APPLIED THERMAL ENGINEERING (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Energy & Fuels

Thermoelectric Generation From Exhaust Heat in Electrified Natural Gas Trucks: Modeling and Analysis of an Integrated Engine System Performance Improvement

Ratnak Sok et al.

Summary: Using thermoelectric generators (TEG) can improve emissions and fuel economy of conventional and electrified vehicles by reducing exhaust heat loss from internal combustion engines. This study demonstrates the effectiveness of TEG in boosting a hybridized CNG engine. By calibrating a model with experimental data, the model can accurately predict thermal performances. The results show that using TEG can improve the engine's brake thermal efficiency (BTE) by up to 0.8% without significant brake power loss.

JOURNAL OF ENERGY RESOURCES TECHNOLOGY-TRANSACTIONS OF THE ASME (2023)

添加到收藏夹

Article Thermodynamics

Improving the ability of thermoelectric generators to absorb industrial waste heat through three-dimensional structure optimization

Zhuang Miao et al.

Summary: In this study, thermoelectric conversion technology is used to recover industrial radiant heat, and the ability of the thermoelectric generator (TEG) to absorb radiant heat is effectively improved by optimizing the heat collector's structure. The heat transfer process between the industrial environment and TEG is analyzed by a numerical calculation method to reduce research cost. The influence of the heat collector's structure on the power generation performance is analyzed, and the optimal structure scheme is determined based on calculation results.

APPLIED THERMAL ENGINEERING (2023)

添加到收藏夹

Article Thermodynamics

Development and validation of thermal performances in a novel thermoelectric generator model for automotive waste heat recovery systems

Ratnak Sok et al.

Summary: Integrated thermoelectric generators (TEGs) and heat exchangers (HEX) are important for converting heat into electrical power. This study develops a 1D TEG model using the model-based development (MBD) method and focuses on the heat transfer coefficient alpha, pressure drop AP, and component temperatures that affect the electrical power from thermoelectric modules (TEM). Two methods are used to develop the model, with Method 2 achieving good performance without model tuning. The fast-predictive TEG model can be used for TEG redesign and integrated into vehicle-level simulations.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2023)

添加到收藏夹

Article Thermodynamics

Numerical and Experimental Study on Performance of a Low-Backpressure Polyhedral Thermoelectric Generator for Waste Heat Recovery

Quan Rui et al.

Summary: Optimizing the arrangement and dimensions of heat exchangers can improve the maximum output power of TEG systems. A low-backpressure TEG system based on a polyhedral-shape heat exchanger was developed and validated through numerical simulations. The results demonstrate that increasing fin length, width, and intersection angle improves system performance, while decreasing fin spacing contributes to higher average surface temperature and maximum power.

JOURNAL OF THERMAL SCIENCE (2023)

添加到收藏夹

Review Thermodynamics

Exploratory review of the heat exchanger and cooler geometrical effect on energy harvesting from automobile exhaust using thermoelectric generators

Mohammed Y. Y. Jabbar et al.

Summary: Extensive studies have been conducted on powder metallurgy technology for manufacturing thermoelectric generator couples and improving their power efficiency by altering the internal and external structures of the heat exchangers and coolers. The review also addresses the impact of cooling techniques and metal materials on the output power. The conclusions provide valuable insights for designing heat exchangers and coolers, including the need to minimize pressure drop and optimize fuel consumption.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2023)

添加到收藏夹

Article Thermodynamics

Experimental and modeling analysis on thermoelectric heat recovery to maximize the performance of next-generation diesel engines dedicated for future electrified powertrains

Ratnak Sok et al.

Summary: Thermoelectric generators can recover energy loss from exhaust heat and improve brake thermal efficiency of internal combustion engine vehicles. This study uses a model-based design approach to maximize the performance of a next-generation diesel engine through thermoelectric module optimization, achieving an improvement in effective power.

APPLIED THERMAL ENGINEERING (2023)

添加到收藏夹

Article Thermodynamics

Design optimization of plate-fin heat sink with forced convection for single-module thermoelectric generator

Toni Pujol et al.

Summary: A semi-analytical model was developed to predict the maximum net electrical power of a thermoelectric generator with a plate-fin heat sink. The model was successfully validated with experimental data. The model can be used to determine the optimal heat sink design for maximizing the net electrical power.

APPLIED THERMAL ENGINEERING (2023)

添加到收藏夹

Article Thermodynamics

Performance analysis of compact thermoelectric generation device for harvesting waste heat

Peiyong Ni et al.

Summary: A compact thermoelectric power generation (TEG) device with two heat collectors and three water coolers was designed to save energy and effectively utilize waste heat from diesel engines. A three-dimensional steady-state fluid-solid coupling simulation was performed to analyze the heat transfer characteristics, temperature and flow fields of the device. Experimental investigations on a TEG test bench showed that the device generated a maximum output power of 15.8 W under certain operating conditions. More studies are needed for the optimization of multiphysics simulation and comprehensive evaluation of heat transfer and power generation performance.

ENERGY CONVERSION AND MANAGEMENT (2023)

添加到收藏夹

Article Thermodynamics

Effect of structure parameters on the performance of an annular thermoelectric generator for automobile exhaust heat recovery

Zu-Guo Shen et al.

Summary: This study examines the impact of five structural parameters on the power and net power density of automotive exhaust annular thermoelectric generators using a theoretical model and finite element method, and provides design recommendations based on the findings.

ENERGY CONVERSION AND MANAGEMENT (2022)

添加到收藏夹

Article

An Experimental Investigation on Heat Transfer Enhancement in An Annulus with Rotating Outer Cylinder Using Nano Fluids

Samer Mahmood Khalaf et al.

Tikrit Journal of Engineering Sciences (2022)

添加到收藏夹

Article

Effect Of Pooled and Flat Stepped Spillway on Energy Dissipation Using Computational Fluid Dynamics

Shawnm Mudhafar Saleh et al.

Tikrit Journal of Engineering Sciences (2022)

添加到收藏夹

Article Thermodynamics

Performance interaction assessment of automobile exhaust thermoelectric generator and engine under different operating conditions

Rui Quan et al.

Summary: The structure optimization of heat exchanger can enhance the output performance of a thermoelectric generator (TEG) used for automobile exhaust recovery. However, connecting the heat exchanger to the internal combustion engine (ICE) may lead to increased backpressure and deteriorative performance. This study sets up and validates a comprehensive numerical model to assess the performance interaction between automobile exhaust thermoelectric generator (AETEG) and ICE with different heat exchangers. The results show that the operating condition and inner topology of ICE have obvious influences on the backpressure of the heat exchanger, with the chaos shape heat exchanger having the largest backpressure. The increased backpressure affects various parameters of ICE and AETEG, such as pumping mean effective pressure (PMEP), hot side temperature, output power, brake power, brake torque, volumetric efficiency, fuel economy, and emissions. The findings provide valuable insights for the development, topology optimization, and performance assessment of a low-backpressure AETEG without significantly impacting the ICE performance.

APPLIED THERMAL ENGINEERING (2022)

添加到收藏夹

Article Green & Sustainable Science & Technology

Economic configuration optimization of onboard annual thermoelectric generators under multiple operating conditions

WenChao Zhu et al.

Summary: This paper establishes an advanced non-isothermal mathematical model of automobile annular thermoelectric generators (ATEGs) using the finite element method. The effects of different vehicle operating conditions on the optimal thermoelectric semiconductor volume are investigated, and the optimal range for selecting the thermocouple volume is determined. Two new schemes are proposed to optimize the system configuration and a new method for assessing the power generation cost is proposed. The optimal design is obtained and the results show its advantages in net power and efficiency.

RENEWABLE ENERGY (2022)

添加到收藏夹

Article

The Effect of Exterior Wall Color on Thermal Performance of Building

Hassan Kareem Abdullah et al.

Tikrit Journal of Engineering Sciences (2022)

添加到收藏夹

Article Thermodynamics

Performance analysis of thermoelectric generation system with controlled heat distribution

Xue-Qing Dong et al.

Summary: A new model of thermoelectric power generation system with double collectors was proposed, demonstrating that controlled heat distribution can increase output power, but the optimal opening ratio was still less than 1 at high input temperatures.

ENERGY CONVERSION AND MANAGEMENT (2021)

添加到收藏夹

Article Thermodynamics

A novel super-cooling enhancement method for a two-stage thermoelectric cooler using integrated triangular-square current pulses

Jing-Hui Meng et al.

Summary: A novel concept of continuous cooling has been proposed in this work to enhance the super-cooling performance of a two-stage thermoelectric cooler. By optimizing pulse forms using the NSGA-II algorithm, better super-cooling performance was achieved with maximum effective cooling zone and minimum temperature overshoot as the multi-objective function.

ENERGY (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Experimental investigation on the influence of phase change material on the output performance of thermoelectric generator

Jun Wang et al.

Summary: Thermal management of thermoelectric generator systems is crucial, and using phase change materials can effectively reduce temperature fluctuations and extend operation time, although it cannot achieve the peak output power of common systems.

RENEWABLE ENERGY (2021)

添加到收藏夹

Article Energy & Fuels

Performance comparison of annular and flat-plate thermoelectric generators for cylindrical hot source

Mengjun Zhang et al.

Summary: This study compares the performances of annular thermoelectric generator (ATEG) and flat-plate thermoelectric generator (FTEG) with varying inlet temperature, velocity, and convective heat transfer coefficient when applied to cylindrical heat sources. The results show that both the output power and conversion efficiency of ATEG and FTEG increase with higher inlet velocity, temperature, and convective heat transfer coefficient. ATEG consistently exhibits higher conversion efficiency than FTEG, especially when the inlet temperature and/or convective heat transfer coefficient are relatively larger.

ENERGY REPORTS (2021)

添加到收藏夹

Article Thermodynamics

Performance analysis and design optimization of a compact thermoelectric generator with T-Shaped configuration

Tao Yin et al.

Summary: A compact thermoelectric generator (TEG) configuration composed of T-shaped electrodes and connected PeN thermoelectric legs was developed to improve performance. The specific output power of the T-shaped TEG was greatly increased by 90.1% compared to conventional p-shaped TEGs. Detailed studies on coupled thermal-electrical conditions, thermal conditions, and geometric parameters were conducted, along with discussions on geometric optimizations and improvements in power generation under different heat transfer conditions.

ENERGY (2021)

添加到收藏夹

Article Energy & Fuels

Effects of leg geometry and multistaging of thermoelectric modules on the performance of a photovoltaic-thermoelectric system using different photovoltaic cells

Chika Maduabuchi et al.

Summary: Research on enhancing the performance of photovoltaic systems using thermoelectric generators has attracted increasing interest. The circular leg geometry of TEG was found to provide the highest PV-TE performance for both types of PV cells studied. Additionally, the type of PV cell significantly affects the optimal number of TEG stages in the PV-TE system.

INTERNATIONAL JOURNAL OF ENERGY RESEARCH (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Thermoelectric performance and stress analysis on wearable thermoelectric generator under bending load

Shifa Fan et al.

Summary: A three-dimensional model of wearable TEGs encapsulated in PDMS material was established to investigate their thermoelectric performance and mechanical reliability under bending loads. The study examined the effects of leg shape, filling factor, and leg height on the performance of wearable TEGs, and suggested that increasing the number of thermocouples can enhance thermoelectric performance and flexibility.

RENEWABLE ENERGY (2021)

添加到收藏夹

Article Thermodynamics

Feasibility study on a vehicular thermoelectric generator coupled to an exhaust gas heater to improve aftertreatments efficiency in cold-starts

A. Massaguer et al.

APPLIED THERMAL ENGINEERING (2020)

添加到收藏夹

Article Thermodynamics

The impact of square shape perforations on the enhanced heat transfer from fins: Experimental and numerical study

Thamir K. Ibrahim et al.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2020)

添加到收藏夹

Article Thermodynamics

Enhancing the performance of a thermo-electric generator through multi-objective optimisation of heat pipes-heat sink under natural convection

Ali Elghool et al.

ENERGY CONVERSION AND MANAGEMENT (2020)

添加到收藏夹

Article Energy & Fuels

Parametric study of asymmetric thermoelectric devices for power generation

Ding Luo et al.

INTERNATIONAL JOURNAL OF ENERGY RESEARCH (2020)

添加到收藏夹

Article Energy & Fuels

A numerical study on the performance of a converging thermoelectric generator system used for waste heat recovery

Ding Luo et al.

APPLIED ENERGY (2020)

添加到收藏夹

Article Thermodynamics

Performance and profit analysis of thermoelectric power generators mounted on channels with different cross-sectional shapes

Shu-Rong Yan et al.

APPLIED THERMAL ENGINEERING (2020)

添加到收藏夹

Article Thermodynamics

Multi-objective optimization to enhance the performance of thermo-electric generator combined with heat pipe-heat sink under forced convection

Ali Elghool et al.

ENERGY (2020)

添加到收藏夹

Article Thermodynamics

Modelling and simulation study of a converging thermoelectric generator for engine waste heat recovery

Ding Luo et al.

APPLIED THERMAL ENGINEERING (2019)

添加到收藏夹

Article Thermodynamics

Thermal and acoustic performance of an integrated automotive thermoelectric generation system

QiuShi Wan et al.

APPLIED THERMAL ENGINEERING (2019)

添加到收藏夹

Article Thermodynamics

Experimental and numerical investigation of heat transfer augmentation in heat sinks using perforation technique

Thamir K. Ibrahim et al.

APPLIED THERMAL ENGINEERING (2019)

添加到收藏夹

Article Thermodynamics

Numerical analysis on the segmented annular thermoelectric generator for waste heat recovery

Shifa Fan et al.

ENERGY (2019)

添加到收藏夹

Review Thermodynamics

Automotive exhaust thermoelectric generators: Current status, challenges and future prospects

Zu-Guo Shen et al.

ENERGY CONVERSION AND MANAGEMENT (2019)

添加到收藏夹

Article Chemistry, Physical

Comparison and parametric study of two theoretical modeling approaches based on an air-to-water thermoelectric generator system

Ding Luo et al.

JOURNAL OF POWER SOURCES (2019)

添加到收藏夹

Article Thermodynamics

Experimental and numerical study of forced convection heat transfer in different internally ribbed tubes configuration using TiO2 nanofluid

Aadel A. R. Al Kumait et al.

HEAT TRANSFER-ASIAN RESEARCH (2019)

添加到收藏夹

Article Energy & Fuels

A method to assess the fuel economy of automotive thermoelectric generators

A. Massaguer et al.

APPLIED ENERGY (2018)

添加到收藏夹

Article Energy & Fuels

Thermal analysis of a thermoelectric generator for light-duty diesel engines

Pablo Fernandez-Yanez et al.

APPLIED ENERGY (2018)

添加到收藏夹

Article Thermodynamics

Optimization of thermoelectric generator (TEG) integrated with three-way catalytic converter (TWC) for harvesting engine's exhaust waste heat

Haoqi Yang et al.

APPLIED THERMAL ENGINEERING (2018)

添加到收藏夹

Article Thermodynamics

Configuration optimization of the segmented modules in an exhaust-based thermoelectric generator for engine waste heat recovery

Gequn Shu et al.

ENERGY (2018)

添加到收藏夹

Article Thermodynamics

Thermoelectric performance optimization when considering engine power loss caused by back pressure applied to engine exhaust waste heat recovery

Wei He et al.

ENERGY (2017)

添加到收藏夹

Review Thermodynamics

A review on heat sink for thermo-electric power generation: Classifications and parameters affecting performance

Ali Elghool et al.

ENERGY CONVERSION AND MANAGEMENT (2017)

添加到收藏夹

Proceedings Paper Energy & Fuels

Investigation on the performance of a prototype of thermo-electric generation with heat pipe-heat sink

Ali Elghool et al.

UTP-UMP SYMPOSIUM ON ENERGY SYSTEMS 2017 (SES 2017) (2017)

添加到收藏夹

Article Thermodynamics

Numerical investigation on the performances of automotive thermoelectric generator employing metal foam

WanRong Bai et al.

APPLIED THERMAL ENGINEERING (2017)

添加到收藏夹

Article Engineering, Electrical & Electronic

Simulation and Optimization of the Heat Exchanger for Automotive Exhaust-Based Thermoelectric Generators

C. Q. Su et al.

JOURNAL OF ELECTRONIC MATERIALS (2016)

添加到收藏夹

Article Energy & Fuels

Enhancement of maximum temperature drop across thermoelectric cooler through two-stage design and transient supercooling effect

Hao Lv et al.

APPLIED ENERGY (2016)

添加到收藏夹

Article Thermodynamics

Multi-objective optimization of heat exchanger in an automotive exhaust thermoelectric generator

C. Liu et al.

APPLIED THERMAL ENGINEERING (2016)

添加到收藏夹

Review Green & Sustainable Science & Technology

A comprehensive review of thermoelectric technology: Materials, applications, modelling and performance improvement

Ssennoga Twaha et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2016)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.