☆ 4.7 Article

Comprehensive investigation into grinding characteristics and damage behavior of Cf/SiC composite modified by picosecond-laser ablating

COMPOSITE STRUCTURES (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Enhancing the machinability of Cf/SiC composite with the assistance of laser-induced oxidation during milling

Guolong Zhao et al.

Summary: In this study, a novel hybrid machining process called laser-induced oxidation-assisted milling (LOAM) was proposed to enhance the machinability of Cf/SiC composites. The LOAM process improved material removal rate, tool life, and surface quality by inducing a reaction between the composites and oxygen. The results showed that LOAM achieved high-efficiency processing and low-defect surfaces when machining Cf/SiC composites.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Mechanics

Progressive failure analysis of needle-punched C/SiC composites based on multiscale finite element model

Yang Liu et al.

Summary: In this study, a multiscale model combining the finite element method was established to analyze the progressive failure of needle-punched C/SiC composites. Microscopic failure modes under different loads were first analyzed using Micro-RVE, and then coupled with a damage evolution model to calculate the stress-strain relationship and macroscopic failure mode. The strength reduction of the composite under tensile-torsional coupling load was also analyzed. This study effectively revealed the damage evolution process, the relationship between macroscopic load and microscopic failure, and the tensile-torsional coupling failure mechanism of needle-punched C/SiC composites.

COMPOSITE STRUCTURES (2023)

添加到收藏夹

Article Materials Science, Ceramics

Effects of ultrasonic vibration assisted milling with laser ablation pretreatment on fatigue performance and machining efficiency of SiCf/ SiC composites

Chenguang Wang et al.

Summary: Due to the poor machinability of SiCf/SiC parts, many problems arise, such as low efficiency, poor quality, and high cost, which limit its manufacturing and application. A novel process called UVAMLAP was proposed to optimize the fatigue performance and machining efficiency of SiCf/SiC parts. The results showed that UVAMLAP improved surface quality and increased tensile strength by 9.4% and residual tensile strength by 13.5%. The process can prevent damage aggravation, weaken fractures and debonding, and reduce fatigue performance degradation caused by machining damage. Additionally, it reduced machining time by 31.3% and tool cost by 75%.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

添加到收藏夹

Article Materials Science, Ceramics

Machinability improvement in milling of SiCf/SiC composites based on laser controllable ablation pretreatment

Jie Chen et al.

Summary: The poor machinability of SiCf/SiC composites greatly limits its application and promotion. The laser-induced ablation products of SiCf/SiC composites are powdery, loose, and porous. A laser ablation pretreatment milling (LAPM) process was proposed to improve the machining efficiency and machinability of SiCf/SiC composites. LAPM could achieve the cutting allowance in only one pass after laser ablation treatment, greatly reducing the processing time and improving the material removal rate.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

添加到收藏夹

Article Engineering, Mechanical

Investigations of the mechanical and high-temperature tribological properties of the Inconel 718 alloy formed by selective laser melting

JinFang Peng et al.

Summary: Selective laser melting (SLM) is a 3D printing technology used for manufacturing high-precision metal parts with complex geometries. This study focused on investigating the microstructure, microhardness, and tensile strength of an Inconel 718 superalloy synthesized using SLM technology. The wear characteristics of the alloy at various temperatures were examined, and the wear damage mechanisms were analyzed. The study found that SLM-formed Inconel 718 had columnar grains with improved dispersion along the horizontal axis, higher microhardness in the vertical plane, and higher horizontal tensile strength compared to the vertical direction.

TRIBOLOGY INTERNATIONAL (2023)

添加到收藏夹

Article Materials Science, Ceramics

Understanding the machining characteristic of plain weave ceramic matrix composite in ultrasonic-assisted grinding

Menghua Zhang et al.

Summary: This study investigates the effects of different fibre orientations of 2D-Cf/SiC on the grinding force, surface roughness, and surface/subsurface micromorphology in ultrasonic-assisted grinding. The results show that brittle fracture is the predominant material removal mode, and various forms of material breakage occur. Ultrasonic-assisted grinding can effectively decrease the grinding force and improve the surface integrity.

CERAMICS INTERNATIONAL (2022)

添加到收藏夹

Article Materials Science, Ceramics

Modelling and grinding characteristics of unidirectional C-SiCs

Shuoshuo Qu et al.

Summary: This study establishes a theoretical model and a numerical simulation model to research the micro-MRM of C-SiCs, and proves their reliability through experiments. The results show that fiber pull-out, fiber outcrop, matrix cracking, and interfacial debonding are the basic defects in C-SiCs. As the grinding depth increases, the grinding performance of C-SiCs gradually deteriorates.

CERAMICS INTERNATIONAL (2022)

添加到收藏夹

Article Materials Science, Ceramics

Enhancing ductile removal of Cf/SiC composites during abrasive belt grinding using low-hardness rubber contact wheels

Kun Zhou et al.

Summary: This study investigated the removal behavior and surface integrity of C-f/SiC composites during abrasive belt grinding using rubber contact wheels of various hardness. Results revealed that with decreasing hardness of the contact wheel, the surface roughness, grinding force, and temperature decreased significantly. Moreover, the surface and subsurface morphology of the composites also changed.

CERAMICS INTERNATIONAL (2022)

添加到收藏夹

Article Engineering, Industrial

A novel low-damage and low-abrasive wear processing method of Cf/SiC ceramic matrix composites: Laser-induced ablation-assisted grinding

Kun Zhou et al.

Summary: This study proposes a novel high-efficiency, low-damage, and low-abrasive wear processing method for continuous fiber-reinforced ceramic matrix composites. The method combines laser ablation and grinding, resulting in improved grinding performances and surface integrity. The study provides an important method for high-performance processing of ceramic matrix composites components.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Industrial

Drilling process of Cf/SiC ceramic matrix composites: Cutting force modeling, machining quality and PCD tool wear analysis

Benyang Zhang et al.

Summary: This paper investigates tool wear during the machining of C-f/SiC materials. The results indicate that PCD tools with a point angle of 140 degrees and a clearance angle of 20 degrees demonstrate the lowest tool wear. Moreover, low-speed and feed machining parameters can effectively reduce tool wear and prolong tool life. The effects of tool wear on the material removal mechanism are summarized.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Femtosecond laser ablation behavior of SiC/SiC composites in air and water environment

Jiayong Wei et al.

Summary: This study investigated the ablation behavior and mechanisms of SiC/SiC composites in different environments, demonstrating thermochemical corrosion dominance in air and a combination of thermomechanical denudation and thermochemical corrosion in water.

CORROSION SCIENCE (2022)

添加到收藏夹

Review Engineering, Aerospace

Machining of SiC ceramic matrix composites: A review

Qinglong An et al.

Summary: FRCMCs-SiC, as the preferred material for hot section components, safety-critical components, and braking components, faces challenges in machining due to high brittleness, anisotropy, and heterogeneity. With increasing demand for FRCMCs-SiC parts, high-quality and high-efficient machining has become a hot issue.

CHINESE JOURNAL OF AERONAUTICS (2021)

添加到收藏夹

Article Materials Science, Ceramics

Investigating the grinding performance of unidirectional and 2.5D-C/SiCs

Yuying Yang et al.

Summary: This study focuses on the grinding performances of unidirectional and 2.5D-C/SiCs, examining the effects of grinding depth and fibre architecture on grinding force, surface quality, and grinding debris. The study reveals that the grinding depth significantly influences the grinding properties of C/SiCs, with different damage modes observed in the two fibre architectures. The research provides insights for predicting and improving the grinding performance of C/SiCs with different fibre architectures.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Ceramics

Effects of grinding speed on the material removal mechanism in single grain grinding of SiCf/SiC ceramic matrix composite

Jingfei Yin et al.

Summary: This study investigates the effect of grinding speed on the material removal mechanism of SiCf/SiC, showing that high-speed grinding can increase material brittleness and fiber breakage, leading to improved groove surface quality and machining efficiency.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Ceramics

Investigations on continuous-wave laser and pulsed laser induced controllable ablation of SiCf/SiC composites

Jie Chen et al.

Summary: The study investigated the laser-induced ablation mechanism and products of SiCf/SiC composites through numerical simulation and experiments, finding that the ablation depth could be controlled by adjusting laser parameters, with continuous-wave (CW) mode resulting in greater depth. Adjusting the scanning speed and spacing were significant factors in controlling the depth of laser-induced ablation.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Article Materials Science, Ceramics

Experimental investigation on fatigue property at room temperature of C/SiC composites machined by rotary ultrasonic milling

Feng Xue et al.

Summary: The study showed that the use of Rotary Ultrasonic Milling technology in processing C/SiC composites can significantly enhance their fatigue performance, reduce damage rate, and delay damage accumulation and fiber reinforcement stages.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Selection, processing, properties and applications of ultra-high temperature ceramic matrix composites, UHTCMCs - a review

Jon Binner et al.

INTERNATIONAL MATERIALS REVIEWS (2020)

添加到收藏夹

Review Engineering, Manufacturing

The new challenges of machining Ceramic Matrix Composites (CMCs): Review of surface integrity

Oriol Gavalda Diaz et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)

添加到收藏夹

Article Materials Science, Ceramics

Grinding characteristics and removal mechanism of 2.5D-needled Cf/SiC composites

Shuoshuo Qu et al.

CERAMICS INTERNATIONAL (2019)

添加到收藏夹

Article Chemistry, Physical

A Study on the Laser-Assisted Machining of Carbon Fiber Reinforced Silicon Carbide

Khulan Erdenechimeg et al.

MATERIALS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural evolution of carbon fiber reinforced SiC-based matrix composites during laser ablation process

Xiaolin Dang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

添加到收藏夹

Article Chemistry, Physical

The Effects of Laser Parameters and the Ablation Mechanism in Laser Ablation of C/SiC Composite

Sining Pan et al.

MATERIALS (2019)

添加到收藏夹

Article Mechanics

A multi-layer integrated thermal protection system with C/SiC composite and Ti alloy lattice sandwich

Yingjie Xu et al.

COMPOSITE STRUCTURES (2019)

添加到收藏夹

Article Automation & Control Systems

Edge surface grinding of CFRP composites using rotary ultrasonic machining: comparison of two machining methods

Yuanchen Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Ceramics

New observations of the fiber orientations effect on machinability in grinding of C/SiC ceramic matrix composite

Jinguang Du et al.

CERAMICS INTERNATIONAL (2018)

添加到收藏夹

Article Materials Science, Ceramics

Surface topography and roughness of silicon carbide ceramic matrix composites

Shuoshuo Qu et al.

CERAMICS INTERNATIONAL (2018)

添加到收藏夹

Article Materials Science, Ceramics

Influence of grinding fiber angles on grinding of the 2D-Cf /C-SiC composites

Qiong Liu et al.

CERAMICS INTERNATIONAL (2018)

添加到收藏夹

Article Mechanics

Tensile behavior of C/SiC composites plate after hypervelocity penetration: Residual strength and fracture mechanism

Tao Li et al.

COMPOSITE STRUCTURES (2018)

添加到收藏夹

Article Mechanics

Thermal conductivities of plain woven C/SiC composite: Micromechanical model considering PyC interphase thermal conductance and manufacture-induced voids

Yingjie Xu et al.

COMPOSITE STRUCTURES (2018)

添加到收藏夹

Article Automation & Control Systems

Improved machinability of SiC/SiC ceramic matrix composite via laser-assisted micromachining

Xiangyang Dong et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)

添加到收藏夹

Review Materials Science, Multidisciplinary

Design, Preparation and Properties of Carbon Fiber Reinforced Ultra-High Temperature Ceramic Composites for Aerospace Applications: A Review

Sufang Tang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2017)

添加到收藏夹

Article Materials Science, Ceramics

Experimental investigations on grinding characteristics and removal mechanisms of 2D-Cf/C-SiC composites based on reinforced fiber orientations

Qiong Liu et al.

CERAMICS INTERNATIONAL (2017)

添加到收藏夹

Article Chemistry, Physical

Effect of fiber orientations on surface grinding process of unidirectional C/SiC composites

Lifeng Zhang et al.

APPLIED SURFACE SCIENCE (2016)

添加到收藏夹

Article Chemistry, Physical

Study on the machined depth when nanoscratching on 6H-SiC using Berkovich indenter: Modelling and experimental study

Feihu Zhang et al.

APPLIED SURFACE SCIENCE (2016)

添加到收藏夹

Article Materials Science, Ceramics

Comparative study of micro topography on laser ablated C/SiC surfaces with typical uni-directional fibre ending orientations

M. L. Wu et al.

CERAMICS INTERNATIONAL (2016)

添加到收藏夹

Article Chemistry, Physical

Active control of the anisotropic wettability of the carbon fiber reinforced carbon and silicon carbide dual matrix composites (C/C-SiC)

M. L. Wu et al.

APPLIED SURFACE SCIENCE (2015)

添加到收藏夹

Article Materials Science, Ceramics

Ablation behavior of three-dimensional braided C/SiC composites by oxyacetylene torch under different environments

Li Wei et al.

CERAMICS INTERNATIONAL (2013)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.