☆ 4.4 Article

Dual Modification of Hypereutectic Al-Si Alloy and Spheroidization Mechanism of Primary Silicon with Eu Addition

INTERNATIONAL JOURNAL OF METALCASTING (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Metallurgy & Metallurgical Engineering

Effect of Strontium Additions on the Microstructural and Mechanical Properties of Al-17Si-4Cu-0.6Mg-3Zn (B390+2 wt%Zn) Alloy

Merve Calis et al.

Summary: In this study, an Al-17Si-4Cu-0.6Mg-3Zn (B390 + 2 wt%Zn) alloy and five B390 + 2 wt% Zn-Sr alloys were produced by permanent mold casting method. Microstructural evaluations and X-ray diffraction (XRD) studies confirmed the phases of the alloys. Hardness, tensile strength, and elongation to fracture values were determined for the alloys. Sr addition caused significant changes in the microstructure and mechanical properties of the alloys. The hardness and tensile strength of the B390 + 2 wt%Zn-Sr alloys increased with increasing Sr ratio up to 0.075 wt%. The elongation to fracture value of the B390 + 2wt%Zn alloy increased with 0.01 wt% Sr addition, but decreased continuously with increasing Sr content beyond that level.

INTERNATIONAL JOURNAL OF METALCASTING (2023)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Cooling Rate on the Microstructure and Solidification Characteristics of Al-20%Mg2Si In Situ Composites Using Computer-Aided Thermal Analysis Technique

S. Ashkvary et al.

Summary: The formation, size, and morphology of Mg2Si intermetallics in Al-Mg2Si in situ composites significantly influence the mechanical properties of the alloy. Cooling rate during solidification has a direct impact on the microstructure and characteristics of the reinforcement particles. This study investigated the effect of different cooling rates on the microstructure and solidification parameters of Al-20%Mg2Si in situ composite using cooling curve thermal analysis technique. The results showed that increasing the cooling rate resulted in higher nucleation temperature of primary Mg2Si, binary eutectic, and ternary eutectic, while decreasing the growth temperature of the eutectic reactions. Furthermore, the Mg2Si reinforcement particles changed from coarse dendritic to fine polygonal shape, accompanied by decreased size and increased density.

INTERNATIONAL JOURNAL OF METALCASTING (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

The growth mechanism and morphology evolution of primary Si during slow cooling solidification of high purity Al-15Si alloy with Cr additions

Chunyu Li et al.

Summary: The effects of Cr content on the growth mechanism and morphology evolution of primary Si were studied in Al-15Si alloys. The results show that the addition of Cr increases the nucleation undercooling of Si and inhibits macroscopic segregation. The morphology of primary Si transforms from irregular to regular shape and the grain size is reduced in the presence of Cr.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Antimony on the Microstructure Evolution and Mechanical Properties of Hypereutectic Al-Si Rheological High Pressure Die Casting Alloy

Pengyu Yan et al.

Summary: By combining the serpentine pouring channel and Sb modifier, the mechanical properties of A390 aluminum alloy can be improved, with antimony playing a key role in the refinement of eutectic Si. The preparation temperature of the semi-solid slurry also has a significant impact on the mechanical properties.

INTERNATIONAL JOURNAL OF METALCASTING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Morphologically templated nucleation of primary Si on AlP in hypereutectic Al-Si alloys

Xiangzhen Zhu et al.

Summary: In this study, the morphologies of AlP crystals were comprehensively studied, revealing two categories of AlP crystals and their morphological templated nucleation of primary Si phase. This process increased the percentage of primary Si twin crystals in the alloy and eliminated dendritic growth and hopper structures inside primary Si, maintaining faceted solid crystals through layer-by-layer growth mechanism. The insight into morphologically templated nucleation provides a new perspective on the mechanism of heterogeneous nucleation of primary Si phase on AlP nuclei.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Modification mechanism and tensile property of Al-9Si-0.4Mg-0.1Cu alloy

Liang Chang et al.

Summary: The study demonstrated that the Sr element can enhance the modification level of eutectic Si, thereby increasing the tensile strength and elongation of the alloy. However, an excessive amount of Sr can have a detrimental effect on the modification level and mechanical properties.

MATERIALS CHARACTERIZATION (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Modification Mechanism of Rare Earth Eu on Eutectic Si in Hypoeutectic Al-Si Alloy

Feng Mao et al.

Summary: The addition of Eu in Al-7Si alloys changes the morphology of eutectic Si, decreases the number of eutectic cells, increases their size, and lowers the nucleation temperature. Eu also causes phosphorus segregation and affects the growth direction and form of eutectic Si cells.

INTERNATIONAL JOURNAL OF METALCASTING (2022)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Effect of grain refiner, modifier and graphene on the mechanical properties of hyper eutectic Al-Si alloys by experimental and numerical investigation

C. Sumalatha et al.

Summary: This study focuses on investigating the mechanical properties of grain refined and modified die cast hypereutectic Al-16Si alloys, as well as the influence of graphene reinforcement on the samples. Experimental tests and numerical simulations were conducted, and two constitutive models were proposed for predicting the flow stress behavior of the investigated materials.

MATERIALS TODAY-PROCEEDINGS (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

THE COMBINED EFFECT OF COOLING SLOPE PLATE CASTING AND MOLD VIBRATION ON MICROSTRUCTURE, HARDNESS AND WEAR BEHAVIOR OF Al-Si ALLOY (A390)

M. M. Shehata et al.

Summary: The use of mechanical vibration during CSP casting can effectively refine the microstructure of A390 alloy, leading to improved hardness and wear resistance. The refinement was more significant when using a sand mold, showing a reduction in primary Si size and enhanced mechanical properties.

INTERNATIONAL JOURNAL OF METALCASTING (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Comparison of Silicon Phase in Al-20Si Alloys and Zn-27Al-3Si Alloys with Strontium Addition

Feng Mao et al.

Summary: The study on the evolution of the silicon phase in hypereutectic Al-20Si alloys and Zn-27Al-3Si alloys with Sr addition revealed that a 0.2% Sr content helps reduce the precipitation temperature of primary silicon and is advantageous in obtaining spherical primary silicon.

INTERNATIONAL JOURNAL OF METALCASTING (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

The Metallurgy of Aluminum Alloys for Structural High-Pressure Die Castings

Geoffrey K. Sigworth et al.

Summary: Aluminum alloys for high-pressure die casting often have enough dissolved iron to reduce die wear and soldering, but this reduces ductility in the final product. Recent improvements in machine design and new alloys have enabled the production of high ductility, structural HPDC components. This paper details the chemical and metallurgical factors contributing to this development.

INTERNATIONAL JOURNAL OF METALCASTING (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Rare Earth Metals on the Mechanical Properties and Fractography of Al-Si-Based Alloys

M. F. Ibrahim et al.

INTERNATIONAL JOURNAL OF METALCASTING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure evolution and mechanical properties of new die-cast Al-Si-Mg-Mn alloys

Qing Cai et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Chemistry, Physical

Precipitation behavior and mechanical performances of A356.2 alloy treated by Al-Sr-La composite refinement-modification agent

Xingchuan Xia et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Modification of the silicon phase and mechanical properties in Al-40Zn-6Si alloy with Eu addition

Feng Mao et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Formation mechanism and conditions of fine primary silicon being uniformly distributed on single αAl matrix in Al-Si alloys

Lei Zhang et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructural Characteristics, Mechanical Properties, Fracture Analysis and Corrosion Behavior of Hypereutectic Al-13.5Si Alloy

Jelena Scepanovic et al.

INTERNATIONAL JOURNAL OF METALCASTING (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

EFFECT OF Sr-GRAIN REFINER-Si INTERACTIONS ON THE MICROSTRUCTURE CHARACTERISTICS OF Al-Si HYPEREUTECTIC ALLOYS

H. Tahiri et al.

INTERNATIONAL JOURNAL OF METALCASTING (2018)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

EFFECT OF SAMARIUM (SM) ADDITION ON THE MICROSTRUCTURE AND TENSILE PROPERTIES OF Al-20%Si CASTING ALLOY

Qinglin Li et al.

INTERNATIONAL JOURNAL OF METALCASTING (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical Properties and Microstructural Evolution of Yb-Modified Al-20%Si Alloy

Qinglin Li et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2018)

添加到收藏夹

Article Thermodynamics

Interaction of Ca, P trace elements and Sr modification in AlSi5Cu1Mg alloys

Jovid Rakhmonov et al.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Modification of eutectic Si and the microstructure in an Al-7Si alloy with barium addition

Jinsong Rao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the growth mechanism of the primary silicon particle in a hypereutectic Al-20 wt% Si alloy using synchrotron X-ray tomography

J. Wang et al.

MATERIALS & DESIGN (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Cluster formation at the Si/liquid interface in Sr and Na modified Al-Si alloys

Jenifer Barrirero et al.

SCRIPTA MATERIALIA (2016)

添加到收藏夹

Article Multidisciplinary Sciences

Self-organized Sr leads to solid state twinning in nano-scaled eutectic Si phase

M. Albu et al.

SCIENTIFIC REPORTS (2016)

添加到收藏夹

Article Multidisciplinary Sciences

Revealing heterogeneous nucleation of primary Si and eutectic Si by AlP in hypereutectic Al-Si alloys

Jiehua Li et al.

SCIENTIFIC REPORTS (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Modification of eutectic Si in Al-Si alloys with Eu addition

J. H. Li et al.

ACTA MATERIALIA (2015)

添加到收藏夹

Article Chemistry, Physical

Effect of Eu addition on the microstructures and mechanical properties of A356 aluminum alloys

Feng Mao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Complex Modification of Hypereutectic Al-Si Alloy by a New Al-Y-P Master Alloy

Min Zuo et al.

METALS AND MATERIALS INTERNATIONAL (2015)

添加到收藏夹

Article Multidisciplinary Sciences

The roles of Eu during the growth of eutectic Si in Al-Si alloys

Jiehua Li et al.

SCIENTIFIC REPORTS (2015)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

The Modification of Al-Si Casting Alloys: Important Practical and Theoretical Aspects

G. Sigworth et al.

International Journal of Metalcasting (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Phosphorus in Al-Si cast alloys: Thermodynamic prediction of the AlP and eutectic (Si) solidification sequence validated by microstructure and nucleation undercooling data

Song-Mao Liang et al.

ACTA MATERIALIA (2014)

添加到收藏夹

Article Chemistry, Physical

Effect of in situ γ-Al2O3 particles on the microstructure of hypereutectic Al-20%Si alloy

Qinglin Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2013)

添加到收藏夹

Article Chemistry, Physical

Effect of rare earth cerium addition on the microstructure and tensile properties of hypereutectic Al-20%Si alloy

Qinglin Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of P and Sr complex modification on Si phase in hypereutectic Al-30Si alloys

Min Zuo et al.

MATERIALS & DESIGN (2013)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of rare earth Er addition on microstructure and mechanical properties of hypereutectic Al-20% Si alloy

Qinglin Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Refinement of primary Si and modification of eutectic Si for enhanced ductility of hypereutectic Al-20Si-4.5Cu alloy with addition of Al2O3 nanoparticles

Hongseok Choi et al.

JOURNAL OF MATERIALS SCIENCE (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Sc addition on the microstructure and mechanical properties of as-atomized and extruded Al-20Si alloys

M. Fatih Kilicaslan et al.

MATERIALS LETTERS (2012)

添加到收藏夹

Article Chemistry, Physical

Effect of Nd on microstructure and wear resistance of hypereutectic Al-20%Si alloy

W. X. Shi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

HYPEREUTECTIC AL-SI ALLOYS: PRACTICAL CASTING CONSIDERATIONS

J. Jorstad et al.

INTERNATIONAL JOURNAL OF METALCASTING (2009)

添加到收藏夹

Review Metallurgy & Metallurgical Engineering

THE MODIFICATION OF Al-SI CASTING ALLOYS: IMPORTANT PRACTICAL AND THEORETICAL ASPECTS

G. K. Sigworth

INTERNATIONAL JOURNAL OF METALCASTING (2008)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

GRAIN REFINEMENT OF ALUMINUM CASTING ALLOYS

Geoffrey K. Sigworth et al.

INTERNATIONAL JOURNAL OF METALCASTING (2007)

添加到收藏夹

Article Nanoscience & Nanotechnology

Morphologies of primary silicon in hypereutectic Al-Si alloys with melt overheating temperature and cooling rate

C. L. Xu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)

添加到收藏夹

Article Nanoscience & Nanotechnology

FIB and TEM characterization of subsurfaces of an Al-Si alloy (A390) subjected to sliding wear

J Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Eutectic modification of Al-Si alloys with rare earth metals

K Nogita et al.

MATERIALS TRANSACTIONS (2004)

添加到收藏夹

Article Engineering, Industrial

Study on wear properties of aluminium-silicon piston alloy

MM Haque et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.