☆ 4.6 Article

Finite-frequency H∞ control for active chatter suppression in turning

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Manufacturing

Fast-tool-servo-controlled

Zi-Hui Zhu et al.

Summary: A fast-tool-servo-controlled shear-thickening micropolishing method is proposed for removing undesired surface diffraction on diamond-turned microstructured surfaces. The method allows for controllable material removal by adjusting the gap width and achieves improved surface quality.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2023)

添加到收藏夹

Article Engineering, Manufacturing

Experimental investigation into the effect of magnetorheological fluid damper on vibration and chatter in straight turning process

Mohsen Emami et al.

Summary: Magneto-Rheological (MR) dampers have been widely studied for their potential in semi-active control. In this research, an MR damper was designed and tested for its vibration control performance in straight turning operation. It was observed that the MR damper effectively reduced tool vibration and chatter, as well as improved the surface roughness of the machining.

JOURNAL OF MANUFACTURING PROCESSES (2023)

添加到收藏夹

Article Automation & Control Systems

Reluctance-Based Modular Active Damper for Chatter Suppression in Boring Bars With Different Overhangs

Asier Astarloa et al.

Summary: Boring operations are often limited by chatter vibrations caused by the flexibility of boring bars. Passive tuned mass dampers near the tool tip have been proposed as a solution, but they need to be tuned for a specific frequency for each bar. This work presents the development of an active inertial damper based on reluctance, which offers stability improvement over a broad frequency range, enabling chatter-free boring operations at different bar overhangs.

IEEE-ASME TRANSACTIONS ON MECHATRONICS (2023)

添加到收藏夹

Article Automation & Control Systems

An experimental evaluation of particle impact dampers applied on the tool for milling of hardened steel complex surface

Victor Rossi Saciotto et al.

Summary: In the manufacturing of dies and molds, vibrations can be reduced by using impact dampers in the tools. This study analyzes the effect of different materials and geometries acting as impact damper elements and compares the performance of commercial tool holders with dampened tool holders in milling processes. The results show that tools with impact dampers generate smoother surfaces and lower vibrations compared to tools without dampers.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Manufacturing

Chatter suppression for milling of thin-walled workpieces based on active modal control

Jianan Du et al.

Summary: This paper presents an active control method with a piezoelectric patch actuator to suppress milling chatter of thin-walled workpieces. The dynamic model of the workpiece is established using a semi-analytical method, and the actuator position is optimized and an active controller is designed to stabilize the milling process. Experimental results show that the stable cutting depth is improved from 0.2 mm to 1 mm with the designed control method.

JOURNAL OF MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Automation & Control Systems

Active Chatter Mitigation by Optimal Control of Regenerative Machining Process Dynamics

Alper Dumanli et al.

Summary: This article introduces a novel control system design for machine tool feed drives to mitigate chatter vibrations in subtractive manufacturing processes. By utilizing an H-infinity control framework, the proposed controller stabilizes machining dynamics and ensures robust process stability. Experimental validations show that regenerative chatter vibrations in orthogonal turning processes can be effectively suppressed, leading to up to a five-fold increase in MRR.

IEEE-ASME TRANSACTIONS ON MECHATRONICS (2022)

添加到收藏夹

Article Automation & Control Systems

Chatter suppression mechanism and parameters configuration of the spindle speed variation with piecewise characteristics

Zhenmin Li et al.

Summary: This paper presents a novel spindle speed variation strategy with piecewise characteristics, which effectively suppresses chatter. The influence of the strategy on cutting power is considered and some new conclusions are drawn. Additionally, recommendations are given for selecting the SSS amplitude ratio and frequency, and the strategy should be used in conjunction with chatter detection technology.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Industrial

Time delay feedback control for milling chatter suppression by reducing the regenerative effect

Jianan Du et al.

Summary: This paper proposes a time delay feedback control method to suppress chatter in milling process and improve machining efficiency. By reducing the regenerative effect, this method achieves higher energy efficiency. Simulated and experimental results demonstrate the effectiveness of the proposed controller, which enables active chatter suppression in practical manufacturing.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Automation & Control Systems

Active Chatter Mitigation by Optimal Control of Regenerative Machining Process Dynamics

Alper Dumanli et al.

Summary: The article proposes a novel control system design for machine tool feed drives, modulating cutting tool motion based on in-process vibration measurements to mitigate chatter vibrations. The method stabilizes machining process dynamics by controlling delay differential equations and robustly suppresses regenerative chatter vibrations in the orthogonal turning process.

IEEE-ASME TRANSACTIONS ON MECHATRONICS (2022)

添加到收藏夹

Article Engineering, Industrial

Active suppression of milling chatter with LMI-based robust controller and electromagnetic actuator

Xiaohu Li et al.

Summary: A robust controller based on LMI has been developed for active milling chatter suppression, and simulation and experimental results show significant improvements in surface finishes and chatter-free boundaries with the designed controller.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Article Automation & Control Systems

H-infinity controller design for chatter suppression in machining based on integrated cutting and flexible structure model

Prapon Ruttanatri et al.

Summary: This study presents a feedback controller design for chatter suppression in machining, which significantly improves stability regions and shows potential for machining vibration control.

AUTOMATICA (2021)

添加到收藏夹

Article Engineering, Industrial

Active control of high frequency chatter with machine tool feed drives in turning

Alper Dumanli et al.

Summary: The paper introduces a new active vibration control strategy for shaping the Stability Lobe diagram to achieve higher material removal rates. The controller is designed as a feedback filter with optimized parameters to suppress regeneration dynamics. The proposed strategy has been successfully applied to systems with significant vibration suppression effects in turning dynamics.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2021)

添加到收藏夹

Article Automation & Control Systems

Structural vibration control using delayed state feedback via LMI approach: with application to chatter stability problems

Prapon Ruttanatri et al.

Summary: This paper presents a method for active vibration control in machining processes using robust delayed-state feedback control based on Lyapunov-Krasovskii functionals. The controller synthesis problem is formulated as a set of linear matrix inequality equations that can be solved numerically. Evaluations on a hardware-in-the-loop flexible structure test-bed show significant improvements in stability regions with feedback controllers optimized via the LKF stability condition.

INTERNATIONAL JOURNAL OF DYNAMICS AND CONTROL (2021)

添加到收藏夹

Article Automation & Control Systems

An Active Control Method for Chatter Suppression in Thin Plate Turning

Haifeng Ma et al.

IEEE TRANSACTIONS ON INDUSTRIAL INFORMATICS (2020)

添加到收藏夹

Article Engineering, Mechanical

Active chatter suppression for milling process with sliding mode control and electromagnetic actuator

Shaoke Wan et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2020)

添加到收藏夹

Article Automation & Control Systems

Active chatter control in turning processes with input constraint

Haifeng Ma et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Manufacturing

Robust time-delayed H∞ synthesis for active control of chatter in internal turning

Elad Mizrachi et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2020)

添加到收藏夹

Article Engineering, Mechanical

Robust active control based milling chatter suppression with perturbation model via piezoelectric stack actuators

Xingwu Zhang et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

添加到收藏夹

Article Engineering, Manufacturing

Adaptive vibration reshaping based milling chatter suppression

Chenxi Wang et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)

添加到收藏夹

Article Engineering, Mechanical

Adaptive inverse control of chatter vibrations in internal turning operations

M. Fallah et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

添加到收藏夹

Article Engineering, Mechanical

Fuzzy finite-frequency output feedback control for nonlinear active suspension systems with time delay and output constraints

Wenfeng Li et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

添加到收藏夹

Article Automation & Control Systems

Delayed feedback control for chatter suppression in turning machines

I Mancisidor et al.

MECHATRONICS (2019)

添加到收藏夹

Article Engineering, Mechanical

Chatter mitigation for the milling of thin-walled workpiece

Zhao Zhang et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)

添加到收藏夹

Article Acoustics

Active chatter suppression with displacement-only measurement in turning process

Haifeng Ma et al.

JOURNAL OF SOUND AND VIBRATION (2017)

添加到收藏夹

Article Engineering, Manufacturing

Prediction of robust stability boundaries for milling operations with extended multi-frequency solution and structured singular values

David Hajdu et al.

JOURNAL OF MANUFACTURING PROCESSES (2017)

添加到收藏夹

Article Engineering, Industrial

Chatter suppression techniques in metal cutting

J. Munoa et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2016)

添加到收藏夹

Article Automation & Control Systems

Active Damping of Boring Bar Vibration With a Magnetic Actuator

Fan Chen et al.

IEEE-ASME TRANSACTIONS ON MECHATRONICS (2015)

添加到收藏夹

Article Engineering, Manufacturing

Model predictive control to mitigate chatters in milling processes with input constraints

Hai-Tao Zhang et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2015)

添加到收藏夹

Article Acoustics

Design and implementation of two-degree-of-freedom tuned mass damper in milling vibration mitigation

Yiqing Yang et al.

JOURNAL OF SOUND AND VIBRATION (2015)

添加到收藏夹

Article Automation & Control Systems

Auxiliary function-based integral inequalities for quadratic functions and their applications to time-delay systems

PooGyeon Park et al.

JOURNAL OF THE FRANKLIN INSTITUTE-ENGINEERING AND APPLIED MATHEMATICS (2015)

添加到收藏夹

Article Automation & Control Systems

Optimal control for chatter mitigation in milling-Part 1: Modeling and control design

Jeremie Monnin et al.

CONTROL ENGINEERING PRACTICE (2014)

添加到收藏夹

Article Automation & Control Systems

Robust Active Chatter Control in the High-Speed Milling Process

Niels J. M. van Dijk et al.

IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY (2012)

添加到收藏夹

Article Automation & Control Systems

Active Suspension Control With Frequency Band Constraints and Actuator Input Delay

Weichao Sun et al.

IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS (2012)

添加到收藏夹

Review Engineering, Manufacturing

A review of chatter vibration research in turning

M. Siddhpura et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2012)

添加到收藏夹

Article Engineering, Manufacturing

Optimization of multiple tuned mass dampers to suppress machine tool chatter

Y. Yang et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2010)

添加到收藏夹

Article Engineering, Mechanical

Improvement of chatter stability in boring operations with passive vibration absorbers

M. H. Miguelez et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2010)

添加到收藏夹

Article Automation & Control Systems

Automatic In-Process Chatter Avoidance in the High-Speed Milling Process

N. J. M. van Dijk et al.

JOURNAL OF DYNAMIC SYSTEMS MEASUREMENT AND CONTROL-TRANSACTIONS OF THE ASME (2010)

添加到收藏夹

Article Automation & Control Systems

Control approaches to the suppression of machining chatter using active magnetic bearings

Min Chen et al.

IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY (2007)

添加到收藏夹

Article Automation & Control Systems

Generalized KYP lemma: Unified frequency domain inequalities with design applications

T Iwasaki et al.

IEEE TRANSACTIONS ON AUTOMATIC CONTROL (2005)

添加到收藏夹

Article Engineering, Multidisciplinary

Updated semi-discretization method for periodic delay-differential equations with discrete delay

T Insperger et al.

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.