☆ 4.7 Article

Fatigue crack growth behavior of selective laser melted martensitic stainless steel

INTERNATIONAL JOURNAL OF FATIGUE (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Tempering Effect on the Anisotropic Mechanical Properties of Selective Laser Melted 420 Stainless Steel

Chong-Ming Jiang et al.

Summary: This study investigates the relationship between build orientation, heat treatment, microstructure, and mechanical properties of AISI 420 martensitic stainless steel fabricated by selective laser melting (SLM). The direction of build orientation significantly affects the strength and ductility of the material, with the parallel build direction exhibiting better properties. Heat treatment also plays a role in improving the anisotropic tensile strength, although it reduces elongation. The microstructure of the SLM builds is responsible for the observed anisotropic properties.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2023)

添加到收藏夹

Article Mechanics

Anisotropic fracture toughness of a selective laser melted martensitic stainless steel

Chong-Ming Jiang et al.

Summary: The anisotropic fracture toughness of selectively laser melted AISI 420 in two build directions was investigated, and post-process heat treatments were performed to study the tempering effect. The parallel group exhibited superior fracture toughness both in as-built and tempered states. The 400 degrees C tempered state showed higher KIC value due to the presence of a coarser martensite phase. The elongated cellular structure was responsible for the anisotropic behavior, unaffected by the tempering treatments.

ENGINEERING FRACTURE MECHANICS (2023)

添加到收藏夹

Article Engineering, Manufacturing

Adapting L-PBF process for fine powders: a case study in 420 stainless steel

Subrata Deb Nath et al.

Summary: The study demonstrates that finer particles can be successfully processed by laser-powder bed fusion to achieve comparable quality and performance to traditional sizes. The critical barrier lies in the agglomeration of fine powders, which can be addressed through a simple vibratory sieving process.

MATERIALS AND MANUFACTURING PROCESSES (2022)

添加到收藏夹

Article Engineering, Mechanical

Near-threshold fatigue crack growth in laser powder bed fusion produced alloy 718

Halsey E. Ostergaard et al.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

添加到收藏夹

Review Automation & Control Systems

Laser powder bed fusion of the steels used in the plastic injection mould industry: a review of the influence of processing parameters on the final properties

Angela Cunha et al.

Summary: This review provides a critical overview of the influence of laser powder bed fusion (LPBF) processing parameters on the final properties of steels used in the plastic injection mould industry, and presents a comprehensive summary and discussion of the physical, mechanical, tribological, corrosion, and thermal properties influenced by LPBF processing parameters.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

添加到收藏夹

Review Materials Science, Multidisciplinary

Fatigue behaviour of laser powder bed fusion (L-PBF) Ti-6Al-4V, Al-Si-Mg and stainless steels: a brief overview

L. Afroz et al.

Summary: Fatigue and crack growth characteristics are crucial properties of additively manufactured (AM) components for load-bearing applications. However, there is less research literature on these properties compared to static properties. The fatigue behavior of AM components is more complex due to factors such as defect distribution, microstructure inhomogeneity, and anisotropy. Therefore, understanding fatigue performance under different loading conditions is essential for enhancing the use of AM in aerospace, automotive, and other industries.

INTERNATIONAL JOURNAL OF FRACTURE (2022)

添加到收藏夹

Article Engineering, Mechanical

Crystallographic analysis of fatigue fracture initiation in 8Ni-0.1C martensitic steel

Kazuho Okada et al.

Summary: This study found that block boundaries in lath martensite structure are the primary initiation sites for fatigue cracks in as-quenched martensitic steel. The incompatibility of plastic strains between adjacent blocks was identified as the cause of initial fatigue crack formation at block boundaries, while plastic deformation along {0 1 1} slip planes also played a significant role in transgranular crack propagation.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fracture and fatigue in additively manufactured metals

Thorsten Hermann Becker et al.

Summary: This review provides a comprehensive overview of the current understanding of structure-property correlations in AM alloys, highlighting the unique aspects of microstructures, process-related attributes, and their effects on mechanical properties. The interplay between microstructures and process attributes in determining structural integrity of AM alloys is emphasized, along with strategies for improving damage tolerance through processing conditions and post-processing treatments. Gaps in understanding fatigue and fracture in AM alloys are identified as future research avenues for widespread deployment and reliable design of engineering components.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanical anisotropy of additively manufactured stainless steel 316L: An experimental and numerical study

A. Charmi et al.

Summary: The mechanical anisotropy in additively manufactured parts, specifically in stainless steel 316L, is mainly influenced by crystallographic texture. Through experiments, it was found that a crystal plasticity model accurately predicted the mechanical behavior of the AM specimens.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Laser powder bed fusion of ultra-high-strength 420 stainless steel: Microstructure characterization, texture evolution and mechanical properties

Yuan Tian et al.

Summary: The study fabricated AISI 420 stainless steel samples using the laser powder bed fusion process, and evaluated the microstructure, texture, and mechanical properties in both as-printed and heat-treated conditions. The results showed that heat treatment resulted in improved tensile and yield strength, although there was a decrease in elongation. Additionally, the toughness was significantly higher after heat treatment.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Chemistry, Physical

Effects of Laser Spot Size on the Mechanical Properties of AISI 420 Stainless Steel Fabricated by Selective Laser Melting

Xi-Huai Yang et al.

Summary: The study shows that the laser spot size significantly affects the mechanical properties of AISI 420 stainless steel fabricated by SLM, with larger spot diameters resulting in rougher surfaces, lower densities, and lower tensile strengths. A volumetric energy density of 80 J/mm(3) proves to be suitable for achieving complete melting of the powder and stable melt pool in the given SLM processing and material system.

MATERIALS (2021)

添加到收藏夹

Review Nanoscience & Nanotechnology

Steels in additive manufacturing: A review of their microstructure and properties

P. Bajaj et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Mechanics

Effects of crack orientation and heat treatment on fatigue-crack-growth behavior of AM 17-4 PH stainless steel

Aref Yadollahi et al.

ENGINEERING FRACTURE MECHANICS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure-sensitive fatigue crack growth in lath martensite of low carbon steel

Shohei Ueki et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Engineering, Mechanical

Near-threshold fatigue crack growth behavior of 10% Cr martensitic steel welded joint with 9% Cr weld metal in high temperature air

Qixing Sun et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Near-threshold fatigue crack growth rates of laser powder b e d fusion produced Ti-6Al-4V

Thorsten Hermann Becker et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Chemistry, Physical

Crack Growth Behavior of Additively Manufactured 316L Steel-Influence of Build Orientation and Heat Treatment

Janusz Kluczynski et al.

MATERIALS (2020)

添加到收藏夹

Review Engineering, Mechanical

Fracture behavior of additively manufactured components: A review

Mohammad Reza Khosravani et al.

THEORETICAL AND APPLIED FRACTURE MECHANICS (2020)

添加到收藏夹

Review Materials Science, Multidisciplinary

A Review of Factors Affecting the Mechanical Properties of Maraging Steel 300 Fabricated via Laser Powder Bed Fusion

Barry Mooney et al.

METALS (2020)

添加到收藏夹

Article Chemistry, Physical

Effects of Build Direction on the Mechanical Properties of a Martensitic Stainless Steel Fabricated by Selective Laser Melting

Ling-Chieh Shen et al.

MATERIALS (2020)

添加到收藏夹

Article Engineering, Chemical

Microstructure-property relationships of 420 stainless steel fabricated for by laser-powder bed fusion

Subrata Deb Nath et al.

POWDER TECHNOLOGY (2019)

添加到收藏夹

Article Engineering, Mechanical

Fatigue crack growth behavior of additively manufactured 17-4 PH stainless steel: Effects of build orientation and microstructure

P. D. Nezhadfar et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

The influence of building direction on the fatigue crack propagation behavior of Ti6Al4V alloy produced by selective laser melting

Z. W. Xu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Engineering, Mechanical

Fatigue characteristics of steels manufactured by selective laser melting

Shahriar Afkhami et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

添加到收藏夹

Article Engineering, Mechanical

Study of the effect of heat treatment on fatigue crack growth behaviour of 316L stainless steel produced by selective laser melting

O. Fergani et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2018)

添加到收藏夹

Article Engineering, Mechanical

Long fatigue crack propagation behavior of Inconel 625 processed by laser powder bed fusion: Influence of build orientation and post-processing conditions

J. -R. Poulin et al.

INTERNATIONAL JOURNAL OF FATIGUE (2018)

添加到收藏夹

Review Materials Science, Multidisciplinary

A Review of the As-Built SLM Ti-6Al-4V Mechanical Properties towards Achieving Fatigue Resistant Designs

Dylan Agius et al.

METALS (2018)

添加到收藏夹

Review Materials Science, Multidisciplinary

Anisotropy and heterogeneity of microstructure and mechanical properties in metal additive manufacturing: A critical review

Y. Kok et al.

MATERIALS & DESIGN (2018)

添加到收藏夹

Article Chemistry, Physical

Tensile, fracture, and fatigue crack growth properties of a 3D printed maraging steel through selective laser melting

Jyoti Suryawanshi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanical behavior of selective laser melted 316L stainless steel

Jyoti Suryawanshi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Chemistry, Physical

Effect of substructure on mechanical properties and fracture behavior of lath martensite in 0.1C-1.1Si-1.7Mn steel

Shengci Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

添加到收藏夹

Article Engineering, Mechanical

The achievable mechanical properties of SLM produced Maraging Steel 300 components

Thorsten Hermann Becker et al.

RAPID PROTOTYPING JOURNAL (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

In situ heat treatment in selective laser melted martensitic AISI 420 stainless steels

P. Krakhmalev et al.

MATERIALS & DESIGN (2015)

添加到收藏夹

Article Engineering, Manufacturing

Fabrication and Characterization of AISI 420 Stainless Steel Using Selective Laser Melting

Xiao Zhao et al.

MATERIALS AND MANUFACTURING PROCESSES (2015)

添加到收藏夹

Article Mechanics

On the fatigue crack growth behavior in 316L stainless steel manufactured by selective laser melting

A. Riemer et al.

ENGINEERING FRACTURE MECHANICS (2014)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of liquid metal embrittlement on low cycle fatigue properties and fatigue crack propagation behavior of a modified 9Cr-1Mo ferritic-martensitic steel in an oxygen-controlled lead-bismuth eutectic environment at 350 °C

Xing Gong et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

添加到收藏夹

Article Mechanics

Effect of residual stresses on ductile crack growth resistance

X. B. Ren et al.

ENGINEERING FRACTURE MECHANICS (2010)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.