☆ 4.7 Article

Strong room temperature work hardening in a dual heterogeneous structured ferrous medium entropy alloy

INTERMETALLICS (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Interstitial-driven local chemical order enables ultrastrong face-centered cubic multicomponent alloys

Zhufeng He et al.

Summary: This study presents a universal strategy for designing ultrastrong and ductile face-centered cubic (fcc) multicomponent alloys by introducing interstitial-driven local chemical order (LCO) through simple thermomechanical processing. Fine laths containing interstitial-driven LCO domains have been observed in a prototype FeMnCoCrN alloy, resulting in an ultra-high yield strength of 1.34 GPa and a uniform elongation of 13.9%. This design strategy has also been successfully applied to a multicomponent austenitic steel, suggesting its potential in developing high-performance fcc materials at low cost.

ACTA MATERIALIA (2023)

添加到收藏夹

Article Chemistry, Physical

Heterogeneous microstructural design with a bimodal grain size distribution of a multicomponent alloy by reversion from a strain-induced martensite

Gwun Seong Jeong et al.

Summary: The aim of this study was to design a simple thermo-mechanical process to improve the strength level of multicomponent alloys without sacrificing ductility. By using a reversion process from strain-induced BCC to FCC, a bimodal-grained distribution was achieved. The alloy displayed an excellent combination of strength and ductility, with a yield strength two to three times higher than conventional FCC-based alloys, likely due to the bi-modal-grained distribution and active transformation-induced plasticity in metastable ultrafine FCC grains.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Heterogeneous-structure-induced ultrahigh strength and ductility in a metastable dual-phase Fe60Cr15Ni16Al9 medium entropy alloy

Ran Wei et al.

Summary: The emergence of medium-entropy alloys (MEAs) provides new insights for the design of the next generation structural alloys. In this study, Fe60Cr15Ni15Co10-xAlx (x = 0, 3, 5 and 7 at.%) and Fe60Cr15Ni16Al9 MEAs were designed and prepared. The results show that the volume fraction of body-centered-cubic (BCC) phase increases with the increase of Al content, and replacing Co with Al significantly promotes deformation-induced martensitic transformation from the face-centered-cubic (FCC) to BCC phase in these MEAs. The Fe60Cr15Ni16Al9 MEA with dual-phase structure exhibits excellent mechanical properties at room and cryogenic temperatures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Ultrahigh cryogenic strength and ductility in a duplex metastable ferrous medium-entropy alloy

Qiuyu Gao et al.

Summary: This work presents a unique low-cost medium-entropy alloy (MEA) with ultra-high strength and ductility. The MEA exhibits a duplex partially recrystallized microstructure consisting of FCC and BCC phases, along with high density dislocations and nano-precipitates. It shows excellent yield strength and uniform elongation at both room temperature and cryogenic temperatures, as well as a high ultimate tensile strength at 77K. The excellent cryogenic mechanical properties can be attributed to various factors including high density dislocations, ultra-fine grains, nano-precipitates, Luders deformation, hetero-deformation-induced hardening, and deformation-induced martensitic transformation.

SCRIPTA MATERIALIA (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

High strain rate deformation of aged TRIP Ti-10V-2Fe-3Al (wt.%) examined by in-situ synchrotron X-ray diffraction

B. Ellyson et al.

Summary: Aged TRIP Ti-10V-2Fe-3Al alloy exhibits higher elongations and flow stresses as the strain rate increases, due to tuning of phase stability and microstructural characteristics. However, increasing aging time and/or strain rate reduces the overall propensity for the TRIP effect and extent of transformation. TRIP with omega phase precipitation provides interesting design strategies for engineering applications requiring high strains and energy absorption.

ACTA MATERIALIA (2023)

添加到收藏夹

Article Chemistry, Physical

Annealing-induced abnormally ultrahigh cryogenic strength-ductility synergy in a cold rolled ferrous medium entropy alloy

Zhenhua Han et al.

Summary: A Fe65Ni15Cr10Co10 medium entropy alloy (MEA) with a heterogeneous microstructure was produced using cold rolling and low temperature annealing. The cold rolled and low temperature annealed specimen exhibited abnormally high yield strength and ductility at -196 degrees C compared to the cold rolled specimen. This phenomenon is mainly attributed to the synergy of hetero-deformation induced (HDI) strengthening, boundary strengthening, and transformation-induced plasticity (TRIP) effect.

INTERMETALLICS (2023)

添加到收藏夹

Review Materials Science, Multidisciplinary

High-entropy alloys with heterogeneous microstructure: Processing and mechanical properties

Praveen Sathiyamoorthi et al.

Summary: Engineering metallic materials with excellent mechanical properties, especially strength and ductility, are highly sought after for various applications. Novel approaches to enhance strength-ductility synergy through heterogeneous microstructures have proven effective in overcoming the traditional strength-ductility trade-off. The discovery of high entropy alloys based on multi-principal elements offers wider possibilities for alloy design and the exploration of new alloys with remarkable properties.

PROGRESS IN MATERIALS SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Available online 16 February 2022 Keywords: Compositionally complex alloy Solidification behavior Alloy design Microstructural characterisation Heusler phase by both microstructure, ferential tion temperatures. primary ordered riched the and the ment of dendritic experimental dictions

Silas Wolff-Goodrich et al.

Summary: The complex phase evolution sequence of a promising new high temperature structural alloy Al20Cr20Fe35Ni20Ti5 has been studied in situ using electromagnetic levitation and time-resolved high energy X-ray diffraction, as well as scanning transmission electron microscopy observations. The results show that the alloy initially forms primary dendrites of A2-structured body-centered cubic phase, followed by ordered B2-structured phase in interdendritic regions. Ordered B2 precipitates form within the primary A2-structured dendrites, while the interdendritic B2 regions undergo a continuous decomposition reaction below the solidus. Below approximately 1380 K, the B2 domains likely undergo a continuous ordering transition to the L2 1 phase.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

1.7 Gpa tensile strength in ferrous medium entropy alloy via martensite and precipitation

Praveen Sathiyamoorthi et al.

Summary: In this study, a Fe50Co25Ni10Al5Ti5Mo5 medium entropy alloy was fabricated through casting and processed by hot rolling and heat treatment to achieve high strength via martensitic structure and precipitation. The resulting sample exhibited fine lath martensite structure, two types of precipitates, retained FCC phase, and high dislocation density, leading to superior tensile properties with an extremely high tensile strength of 1.7 GPa and good uniform elongation of 8%.

MATERIALS LETTERS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Excellent cryogenic strength-ductility synergy in duplex stainless steel with heterogeneous lamella structure

Ming Chen et al.

Summary: Severe cold rolling and short-time annealing were used to fabricate ferrite and austenite duplex stainless steel with heterogeneous lamella structure, exhibiting superior cryogenic mechanical properties with a tensile strength of -1650 MPa and an ultimate tensile strain of -30%. The excellent combination of cryogenic strength and ductility was attributed to fine grain size, nanotwins, back-stress hardening, and deformation induced martensitic transformation.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Superior fracture toughness in a high-strength austenitic steel with heterogeneous lamellar microstructure

Gang Niu et al.

Summary: In this study, we have achieved high fracture toughness and ductility in a high-strength austenitic stainless steel through cold rolling, flash annealing, and tempering processes. The steel exhibits a heterogeneous lamellar microstructure composed of reversed austenite lamellae and partially recrystallized austenite lamellae, leading to improved fracture resistance and toughness.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Outstanding cryogenic strength-ductility properties of a cold-rolled medium-entropy TRIP Fe65(CoNi)25Cr9.5C0.5 alloy

E. Povolyaeva et al.

Summary: A new medium-entropy Fe-65(CoNi)(25)Cr9.5C0.5 alloy was investigated for its properties at room and liquid nitrogen temperatures. The alloy exhibited high strength, good ductility, and excellent fracture toughness at cryogenic temperatures. The microstructure analysis suggested a phase transition induced by deformation, and the cold-rolled alloy showed improved mechanical properties compared to the as-cast alloy. Substructure strengthening, interphase strengthening, and solid solution strengthening were identified as contributing factors to the alloy's enhanced performance.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

A novel low-cost and ultrahigh strength FeCoNiCrSi ferrous medium-entropy alloy at room and liquid nitrogen temperatures

Qiuyu Gao et al.

Summary: A novel cost-effective medium-entropy alloy (MEA) with Fe65Co6Ni6Cr15Si8 composition was manufactured and characterized for its microstructure and mechanical properties. The MEAs exhibited excellent tensile strength and uniform elongation at both room temperature (-1.2 GPa and -26%) and low temperature (-1.9 GPa and -31%). The superior mechanical properties were attributed to the ultra-fine grain size, large Luders strain, deformation-induced martensitic transformation, and hetero-deformation-induced strengthening.

MATERIALS LETTERS (2022)

添加到收藏夹

Article Chemistry, Physical

Effect of Al addition on the corrosion behavior of the VCoNi medium- entropy alloys

Zhenhua Han et al.

Summary: The addition of Al worsens the corrosion resistance of VCoNi alloy by promoting the formation of refined grains and enriched BCC phase, accelerating the dissolution of the alloy, and impairing the stability of the passive layer.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of layered heterogeneous microstructure design on the mechanical behavior of medium carbon steel

Jinliang Du et al.

Summary: A heterogeneous microstructure composed of multiscale ferrite and cementite was obtained through warm rolling and short-time annealing process. This microstructure exhibits excellent mechanical properties and elongation.

MATERIALS & DESIGN (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Twinning damping interface design and synergistic internal friction behavior in FeMnCrCo high-entropy alloys

Yi Xu et al.

Summary: This paper investigates the preparation and properties of a novel high-entropy damping alloy. The experimental results show that the alloy exhibits excellent damping performance, which is related to the twin interface, magnetic properties, and phase interface. By adjusting the composition of the alloy, multiple damping mechanisms can be coupled to further enhance the damping performance.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Nanophase precipitation and strengthening in a dual-phase Al0.5CoCrFeNi high-entropy alloy

Haoxue Yang et al.

Summary: In this study, precipitation-hardening in fcc-based high-entropy alloys was achieved by the existence of L1(2) precipitates and B2/bcc conjoint phases in the matrix. The peak ultimate tensile stress reached 1221.5 MPa, nearly double that of the as-cast alloy, while maintaining a plasticity of 21.3%. The formation of the conjoint B2/bcc phase was found to be driven by concentration profiles after long-time aging, impacting the mechanical properties of the alloy.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhancement of strength-ductility balance of heavy Ti and Al alloyed FeCoNiCr high-entropy alloys via boron doping

Yongliang Qi et al.

Summary: By doping extremely little boron into heavy precipitation-hardened high-entropy alloys, the original microstructure can be significantly improved, leading to enhanced tensile ductility and comparable or even better ultimate tensile strength.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Elemental partitions and deformation mechanisms of L12-type multicomponent intermetallics

Jun Zhang et al.

Summary: Multicomponent high-entropy alloys (HEAs) with compositionally disordered elemental arrangement have excellent mechanical properties, but recent studies show that HEAs strengthened by L1(2) ordered intermetallics of the Ni3Al type exhibit superior synergy of strength and ductility. Through density functional theory (DFT) calculations, the elemental partitions and deformation mechanisms in typical multicomponent intermetallics (MCIs) have been studied, revealing preferences and behaviors of different elements in these materials.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Physics, Applied

Metastability engineering of partially recrystallized C-doped non-equiatomic CoCrFeNiMo medium-entropy alloy

Hyeonseok Kwon et al.

Summary: The study presents partial recrystallization as a solution to the low yield strength issue of Ferrous medium-entropy alloys (FeMEAs). By utilizing dislocation strengthening, precipitation strengthening, grain boundary strengthening, twin boundary strengthening, back stress hardening, and transformation-induced plasticity effect, the strength and work hardenability of the FeMEA were significantly improved.

APPLIED PHYSICS LETTERS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Superior phase transformation-assisted mechanical properties of a metastable medium-entropy ferrous alloy with heterogeneous microstructure

Farahnaz Haftlang et al.

Summary: In this study, the mechanical properties of a newly developed Fe-Ni-Co-Mn-Ti-Si medium-entropy alloy with heterogeneous microstructure were investigated. The alloy exhibited high yield strength, high ultimate tensile strength, and good ductility due to hetero-deformation-induced strengthening and high plastic-incompatibility between mechanically induced-martensite and the austenitic matrix.

MATERIALS LETTERS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

2.3 GPa cryogenic strength through thermal-induced and deformation-induced body-centered cubic martensite in a novel ferrous medium entropy alloy

Hyeonseok Kwon et al.

Summary: This study presents a novel FeCoNiAlTiMo medium-entropy alloy with ultra-high tensile strengths at 298K and 77K. Through hot rolling without further heat treatment, a quasi-dual-phase microstructure with high density of dislocations and Mo-rich mu phase precipitates was created, leading to increased strain hardening ability.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Enhanced cryogenic tensile properties with multi-stage strain hardening through partial recrystallization in a ferrous medium-entropy alloy

Jae Wung Bae et al.

Summary: In this study, we demonstrate the formation of partially recrystallized bimodal microstructures in the Fe60Co15Ni15Cr10 (at%) ferrous medium-entropy alloy through a single-step heat treatment after cold-rolling. This process enhances the yield-strength and ultimate-tensile-strength of the alloy while maintaining a persistent ductility of 61%, thus avoiding the strength-ductility trade-off. The retention of deformation substructures allows for a significant increase in yield-strength compared to a fully-recrystallized state.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Chemistry, Physical

Strengthening of ferrous medium entropy alloys by promoting phase transformation

Kaisheng Zhang et al.

Summary: The study focuses on designing a cost-effective Fe65Co10Ni10Cr15 medium-entropy alloy with excellent cryogenic strength of 1.6 GPa and a strain of 56%, demonstrating the highest strength-price ratio among reported MEAs. The alloy's significant strengthening is attributed to hetero-deformation and accelerated deformation-induced phase transformation.

INTERMETALLICS (2021)

添加到收藏夹

Article Multidisciplinary Sciences

Bifunctional nanoprecipitates strengthen and ductilize a medium-entropy alloy

Ying Yang et al.

Summary: This study demonstrates a strategy of using nanoprecipitates to enhance the strength of the matrix while modulating its transformation characteristics, leading to simultaneous improvements in tensile strength and ductility in a single alloy.

NATURE (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Flash annealing yields a strong and ductile medium Mn steel with heterogeneous microstructure

Xinhao Wan et al.

Summary: Flash-annealing is proposed as an alternative method to produce medium Mn steel with retained austenite, resulting in a unique heterogeneous microstructure that enhances strength but slightly reduces ductility compared to conventional austenite reversion treatment.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Simultaneous effects of deformation-induced plasticity and precipitation hardening in metastable non-equiatomic FeNiCoMnTiSi ferrous medium-entropy alloy at room and liquid nitrogen temperatures

Farahnaz Haftlang et al.

Summary: The mechanical properties of a newly developed metastable 65Fe-15Ni-8Co-8Mn-3Ti-Si ferrous medium-entropy alloy were significantly enhanced after short time annealing and aging treatment, showing high yield strength and total elongation at 298K and 77K. This improvement is attributed to synergistic strengthening mechanisms and the contribution of nano-scale precipitates during tensile deformation.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

TWIP and TRIP-associated mechanical behaviors of Fex(CoCrMnNi)100-x medium-entropy ferrous alloys

Hyeon-Uk Jeong et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Short-range order strengthening in boron-doped high-entropy alloys for cryogenic applications

Jae Bok Seol et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Chemistry, Physical

Carbon and nitrogen co-doping enhances phase stability and mechanical properties of a metastable high-entropy alloy

Wanying Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

L21-strengthened face-centered cubic high-entropy alloy with high strength and ductility

Yongliang Qi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Towards ferrous medium-entropy alloys with low-cost and high-performance

Jae Wung Bae et al.

SCRIPTA MATERIALIA (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Deformation mechanisms and enhanced mechanical properties of 304L stainless steel at liquid nitrogen temperature

Jiansheng Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Novel Co-free high performance TRIP and TWIP medium-entropy alloys at cryogenic temperatures

Ran Wei et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ductile-brittle transition of carbon alloyed Fe40Mn40Co10Cr10 high entropy alloys

L. B. Chen et al.

MATERIALS LETTERS (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Annealing-induced abnormal hardening in a cold rolled CrMnFeCoNi high entropy alloy

Ji Gu et al.

SCRIPTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Development of strong and ductile metastable face-centered cubic single-phase high-entropy alloys

Daixiu Wei et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Chemistry, Physical

Effect of sigma phase on thermophysical properties of Fe55Cr45 alloy

Raj Narayan Hajra et al.

INTERMETALLICS (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Ultrastrong duplex high-entropy alloy with 2 GPa cryogenic strength enabled by an accelerated martensitic transformation

Dong Geun Kim et al.

SCRIPTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hierarchical microstructure design to tune the mechanical behavior of an interstitial TRIP-TWIP high-entropy alloy

Jing Su et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of grain size on the tensile behavior of V10Cr15Mn5Fe35Co10Ni25 high entropy alloy

Peyman Asghari-Rad et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Contrasting mechanical behavior in precipitation hardenable AlxCoCrFeNi high entropy alloy microstructures: Single phase FCC vs. dual phase FCC-BCC

Sindhura Gangireddy et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanism of huge Luders-type deformation in ultrafine grained austenitic stainless steel

Si Gao et al.

SCRIPTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Excellent ductility and serration feature of metastable CoCrFeNi high-entropy alloy at extremely low temperatures

Junpeng Liu et al.

SCIENCE CHINA-MATERIALS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Achieving ultra-high strength and ductility in equiatomic CrCoNi with partially recrystallized microstructures

C. E. Slone et al.

ACTA MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Twinning-induced plasticity (TWIP) steels

Bruno C. De Cooman et al.

ACTA MATERIALIA (2018)

添加到收藏夹

Article Chemistry, Physical

Metastable phase decomposition in as-cast Fe-Ni-Co alloys

A. Paganotti et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

The microstructure and high-temperature properties of novel nano precipitation-hardened face centered cubic high-entropy superalloys

Lu Zhang et al.

SCRIPTA MATERIALIA (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Exceptional phase-transformation strengthening of ferrous medium entropy alloys at cryogenic temperatures

Jae Wung Bae et al.

ACTA MATERIALIA (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Phase stability and kinetics of a sigma-phase precipitation in CrMnFeCoNi high-entropy alloys

G. Laplanche et al.

ACTA MATERIALIA (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Grain refinement of non-equiatomic Cr-rich CoCrFeMnNi high-entropy alloys through combination of cold rolling and precipitation of sigma phase

Ken Cho et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

添加到收藏夹

Article Multidisciplinary Sciences

Multicomponent intermetallic nanoparticles and superb mechanical behaviors of complex alloys

T. Yang et al.

SCIENCE (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Trade-off between tensile property and formability by partial recrystallization of CrMnFeCoNi high-entropy alloy

Jae Wung Bae et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Friction stress and Hall-Petch relationship in CoCrNi equi-atomic medium entropy alloy processed by severe plastic deformation and subsequent annealing

Shuhei Yoshida et al.

SCRIPTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Heterogeneous precipitation behavior and stacking-fault-mediated deformation in a CoCrNi-based medium-entropy alloy

Y. L. Zhao et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

The fcc solid solution stability in the Co-Cr-Fe-Mn-Ni multi-component system

Guillaume Bracq et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ductile CoCrFeNiMox high entropy alloys strengthened by hard intermetallic phases

W. H. Liu et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Multidisciplinary Sciences

Metastable high-entropy dual-phase alloys overcome the strength-ductility trade-off

Zhiming Li et al.

NATURE (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Design of a twinning-induced plasticity high entropy alloy

Y. Deng et al.

ACTA MATERIALIA (2015)

添加到收藏夹

Article Chemistry, Physical

Effect of Mn and V on structure and mechanical properties of high-entropy alloys based on CoCrFeNi system

G. A. Salishchev et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes

JW Yeh et al.

ADVANCED ENGINEERING MATERIALS (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.