☆ 4.7 Article

Simultaneously enhanced tensile strength and ductility of nano-Y2O3-reinforced TiAl alloy prepared by directed energy deposition

MATERIALS CHARACTERIZATION (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Microstructure evolution and tensile property of TiAl alloy using continuous direct energy deposition technique

Fang Cheng et al.

Summary: This paper investigates the evolution of microstructure, microhardness, and tensile properties of TiAl alloy prepared using a continuous direct energy deposition technique (CDED). The results show that the alloy consists of columnar grains with very fine (α2+γ) lamellae, and a special duplex γ microstructure forms.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Grain boundary engineering during the laser powder bed fusion of TiC/316L stainless steel composites: New mechanism for forming TiC-induced special grain boundaries

Jing Li et al.

Summary: In this study, a novel machining solution for controlling microstructures in composites during laser powder bed fusion (LPBF) was proposed. The mechanism of special grain boundary and nanotwin formation in TiC/316L stainless steel composite was investigated. By optimizing the process parameters, including laser power, scanning speed, and hatch spacing, the residual stress and grain refinement in the TiC/316LSS composite were successfully achieved.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of Y2O3-bearing Ti-48Al-2Cr-2Nb alloy prepared by selective electron beam melting

Hangyu Yue et al.

Summary: The effects of beam speed on the microstructure, defects, and mechanical properties of Ti-48Al-2Cr-2Nb alloy with nano-Y2O3 addition were studied. The orientation relationship between nano-Y2O3 and the matrix was determined. The Y2O3-bearing TiAl alloys exhibited excellent compressive properties at room temperature, showing potential for applications.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of heat treatment on the microstructure and anisotropy of tensile properties of TiAl alloy produced via selective electron beam melting

Hangyu Yue et al.

Summary: The study systematically investigated the microstructure and anisotropy of tensile properties of SEBM-produced TiAl alloy samples under different processing parameters, revealing the significant influence of annealing on grain morphology and performance, with heat treatment enhancing tensile strength and elongation.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Enhanced creep properties of Y2O3-bearing Ti-48Al-2Cr-2Nb alloys

Yingfei Guo et al.

Summary: The addition of Y2O3 significantly enhanced the creep properties of Ti-48Al-2Cr-2Nb alloy, increasing creep rupture life three times and reducing minimum creep rate by one-third. The presence of Y2O3 hindered dislocation climb and prevented sub-boundary formation, contributing to the excellent creep properties of the doped alloy.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

A β-solidifying TiAl alloy reinforced with ultra-fine Y-rich precipitates

Xu Gu et al.

Summary: The spark plasma sintered TiAl alloy exhibited a refined microstructure with uniform distribution of ultra-fine yttrium-rich precipitates, resulting in excellent tensile properties at room temperature.

SCRIPTA MATERIALIA (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Metastable phase and microstructural degradation of a TiAl alloy produced via selective electron beam melting

Hangyu Yue et al.

Summary: Selective electron beam melting (SEBM) is used to fabricate TiAl alloys with low energy density, resulting in phase transformation, inhomogeneous microstructure, and varying microhardness. The main routes for microstructural degradation are the decomposition of α2 lamellae and coarsening of the lamellar structure, leading to an increase in microhardness with the lamellar colony content.

VACUUM (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Electron beam melted TiC/high Nb?TiAl nanocomposite: Microstructure and mechanical property

B. Gao et al.

Summary: Introducing semi-melt step in the fabrication of TiC/high Nb-TiAl nanocomposite via electron beam melting enhances the microstructure and mechanical properties. Different microstructures and mechanical properties can be achieved by adding different amounts of TiC during the processing.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Chemistry, Physical

High-temperature microstructure stability and fracture toughness of TiAl alloy prepared via electron beam smelting and selective electron beam melting

Hangyu Yue et al.

Summary: This study investigated the high-temperature microstructure stability of TiAl alloys fabricated by electron beam smelting (EBS) and selective electron beam melting (SEBM). The results showed that annealing temperature significantly affected the microstructure and fracture toughness of the alloys.

INTERMETALLICS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Tantalum on the microstructure and properties of Ti-48Al-2Cr-2Nb alloy fabricated via laser additive manufacturing

Zhanqi Liu et al.

Summary: By using Ti48Al2Cr2Nb/Ta mixed powders as raw materials and a laser additive manufacturing technique, Ti48Al2Cr2Nb-xTa alloy specimens were obtained without metallurgical defects. The addition of different Ta contents resulted in changes in microstructures, phase compositions, and tensile properties of the TiAl alloys. The alloy with 5 at.%Ta had the best overall tensile properties, with increased strength and elongation compared to the alloy without Ta addition.

MATERIALS CHARACTERIZATION (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Directed energy deposition (DED) additive manufacturing: Physical characteristics, defects, challenges and applications

David Svetlizky et al.

Summary: Directed energy deposition (DED) is a branch of additive manufacturing (AM) processes that allows for site-specific deposition and repair, alloy design, and complex shape printing. This review critically examines recent advances in laser-material interactions, melt pool thermal behavior, and monitoring techniques, while also discussing critical processing variables, defect formation mechanisms, and high-end applications and challenges associated with DED processing.

MATERIALS TODAY (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Room and high temperature mechanical behavior of Ti-Al-Nb-Mo alloy reinforced with Ti2AlN ceramic particles

Yingmei Tan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Influence of nano-Y2O3 addition on microstructure and tensile properties of high-Al TiAl alloys

Yingfei Guo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Chemistry, Physical

High temperature tensile properties and fracture behavior of Y2O3-bearing Ti-48Al-2Cr-2Nb alloy

Yingfei Guo et al.

INTERMETALLICS (2020)

添加到收藏夹

Article Chemistry, Physical

Formation of columnar lamellar colony grain structure in a high Nb-TiAl alloy by electron beam melting

W. Kan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Chemistry, Physical

Characterisation of titanium aluminide components manufactured by laser metal deposition

A. R. C. Sharman et al.

INTERMETALLICS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural Degradation of Ti-45Al-8Nb Alloy During the Fabrication Process by Electron Beam Melting

Wenbin Kan et al.

JOM (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Variations of microstructure and tensile property of γ-TiAl alloys with 0-0.5 at% C additives

Qiang Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Grain refinement of TiAl-based alloys: The role of TiB2 crystallography and growth

D. Gosslar et al.

ACTA MATERIALIA (2010)

添加到收藏夹

Article Chemistry, Physical

Review of alloy and process development of TiAl alloys

Xinhua Wu

INTERMETALLICS (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Edge-to-edge matching and its applications - Part I. Application to the simple HCP/BCC system

MX Zhang et al.

ACTA MATERIALIA (2005)

添加到收藏夹

Article Nanoscience & Nanotechnology

Mechanisms and effect of microstructure on creep of TiAl-based alloys

S Karthikeyan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.