☆ 4.7 Article

Steel cable bonding in fresh mortar and 3D printed beam flexural behavior

AUTOMATION IN CONSTRUCTION (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Mechanics

Damage evolution process of fiber-reinforced backfill based on acoustic emission three-dimensional localization

Kang Zhao et al.

Summary: The spatial localization of damage evolution caused by fiber-reinforced backfill is critical for predicting rupture location in mining area filling. Through AE three-dimensional localization tests, the damage evolution process and characteristics of fiber-reinforced backfills were studied. The evolution of spatial distribution of AE events not only reflects the spatial location of damage during the loading process but also determines the degree of damage at a certain location based on spatial point density. These results provide a theoretical basis for predicting rupture localization in mine filling.

COMPOSITE STRUCTURES (2023)

添加到收藏夹

Article Construction & Building Technology

Bending behaviour of steel cable reinforced 3D printed concrete in the direction perpendicular to the interfaces

Jianzhuang Xiao et al.

Summary: This study experimentally investigated the bending behavior of reinforced 3D printed concrete in the direction perpendicular to the printing interfaces, finding that reinforcement greatly improves post-peak bending behavior with no obvious anisotropy present in 3DPC specimens.

CEMENT & CONCRETE COMPOSITES (2022)

添加到收藏夹

Article Construction & Building Technology

A comprehensive analysis of buildability of 3D-printed concrete and the use of bi-linear stress-strain criterion-based failure curves towards their prediction

Avinaya Tripathi et al.

Summary: This study evaluates the buildability of 3D printed concrete through a novel approach, using modified compression tests and models to predict failure heights, which enhances control in material design and printing process.

CEMENT & CONCRETE COMPOSITES (2022)

添加到收藏夹

Article Construction & Building Technology

Comparison between methods for indirect assessment of buildability in fresh 3D printed mortar and concrete

Irina Ivanova et al.

Summary: This paper compares different indirect methods for assessing the buildability of 3D printed cementitious materials, discusses their benefits and disadvantages, and considers their potential for automated in-situ control of materials.

CEMENT AND CONCRETE RESEARCH (2022)

添加到收藏夹

Article Engineering, Multidisciplinary

Influence of HPMC and SF on buildability of 3D printing foam concrete: From water state and flocculation point of view

Chao Liu et al.

Summary: This paper studies the effects of hydroxypropyl methylcellulose (HPMC) and silica fume (SF) on the rheological properties and buildability of foam concrete (FC) for 3D printing. It proposes flocculation structural models for 3D printed FC doped with SF and HPMC. HPMC improves the yield stress and buildability of FC by agglomerating cement particles into large and ultra-large flocs, while SF reduces free water movement and contributes to thixotropy and buildability through its adsorption and re-flocculation ability.

COMPOSITES PART B-ENGINEERING (2022)

添加到收藏夹

Article Chemistry, Physical

Bond Behavior of Steel Cords Embedded in Inorganic Mortars

Francesca Roscini et al.

Summary: This paper investigates the bond behavior of steel cords embedded in inorganic matrices, and finds that lime-based mortar provides better bond. The bond-slip relationships and the constitutive relationship of cohesive contact between steel cord and mortar are determined through experiments and numerical simulations, which can assist in the design of more effective strengthening solutions.

MATERIALS (2022)

添加到收藏夹

Article Construction & Building Technology

Relationship between microstructure and strain-hardening behaviour of 3D printed engineered cementitious composites

Binrong Zhu et al.

Summary: The tensile behavior of printed ECC is influenced by its microstructure, including pore structure characteristics, fiber orientation, and fiber dispersion. Printed ECC with certain fiber lengths showed unique tensile ductility and crack width. The differences in microstructure between printed ECC and normal ECC affect their pore structure and tensile properties. Additionally, printed ECC exhibits a more uniform dispersion of fibers and higher tensile strength compared to normal ECC.

CEMENT & CONCRETE COMPOSITES (2022)

添加到收藏夹

Article Construction & Building Technology

Mitigating early age cracking in 3D printed concrete using fibres, superabsorbent polymers, shrinkage reducing admixtures, B-CSA cement and curing measures

G. M. Moelich et al.

Summary: 3D printed concrete is prone to early age cracking, but several mitigation measures, including the addition of polypropylene fibers, application of curing agents and misting water, and the use of special cement, can reduce the severity of cracking. Among these measures, polypropylene fibers have the best effect.

CEMENT AND CONCRETE RESEARCH (2022)

添加到收藏夹

Article Construction & Building Technology

Bond behavior between steel bars and 3D printed concrete: Effect of concrete rheological property, steel bar diameter and paste coating

Zhibin Wang et al.

Summary: This paper investigates the bond behavior between steel bars and 3D printed concrete (3DPC) and explores the effects of preparation technologies, concrete rheological properties, steel bar diameter, and paste coating on the bond strength. The results show that optimizing the rheological properties of fresh concrete and using surface coated steel bars can effectively enhance the bond strength.

CONSTRUCTION AND BUILDING MATERIALS (2022)

添加到收藏夹

Article Construction & Building Technology

Examining layer height effects on the flexural and fracture response of plain and fiber-reinforced 3D-printed beams

Sooraj A. O. Nair et al.

Summary: This study focuses on the effects of layer height parameters on the flexural strength and fracture properties of 3D printed concrete beams. The research shows that smaller layer heights are beneficial for both reinforced and unreinforced 3D printed concrete, although they result in more interfaces and longer printing times.

CEMENT & CONCRETE COMPOSITES (2021)

添加到收藏夹

Article Construction & Building Technology

Interlayer reinforcement of 3D printed concrete by the in-process deposition of U-nails

Li Wang et al.

Summary: Inserting U-shaped nails into concrete during the 3D printing process improves the weak interface bonding between adjacent layers, significantly increasing the tensile and shear strength of 3D printed concrete. This method has great potential and benefits of reducing anisotropy, providing a new approach to enhance the mechanical properties of printed structures.

CEMENT AND CONCRETE RESEARCH (2021)

添加到收藏夹

Article Construction & Building Technology

Modelling the interlayer bond strength of 3D printed concrete with surface moisture

Gerrit Marius Moelich et al.

Summary: This study improves the performance of 3D printed concrete by incorporating superabsorbent polymers and additional water, enhancing thixotropy, buildability, flexural strength, and interlayer adhesion. It also proposes an analytical model to predict the decrease in interlayer adhesion.

CEMENT AND CONCRETE RESEARCH (2021)

添加到收藏夹

Article Construction & Building Technology

Fresh properties of 3D printed mortar with recycled powder

Shaodan Hou et al.

Summary: This study utilized recycled powder to partially replace cement in 3D printed mortar, investigating its properties and confirming the results through 3D printing. The incorporation of RP improved the flowability of 3DPM and showed better strength performance at a certain replacement ratio.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

Plastic shrinkage and cracking of 3D printed mortar with recycled sand

Hanghua Zhang et al.

Summary: This study investigated the plastic shrinkage and cracking of 3D printed mortar mixed with recycled sand, finding that the use of recycled sand exacerbates plastic shrinkage and increases cracking depth in the mortar.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Green & Sustainable Science & Technology

Fiber-reinforced mortar with 100% recycled fine aggregates: A cleaner perspective on 3D printing

Jianzhuang Xiao et al.

Summary: The study evaluated the possibility of fully replacing NFA with RFA for 3DMP through DIC technique, mechanical testing, and microscopic analysis. The results showed that 100% replacement of RFA had limited impact on the failure pattern of 3DP specimens, while the addition of 1% PE fibers changed the failure pattern from brittle to ductile. After reinforcing with fibers, 3DP mortar mixed with 100% RFA exhibited higher mechanical properties and better deformation ability compared to fiber-free mortar with 100% NFA.

JOURNAL OF CLEANER PRODUCTION (2021)

添加到收藏夹

Review Construction & Building Technology

Integrating reinforcement in digital fabrication with concrete: A review and classification framework

Viktor Mechtcherine et al.

Summary: This article provides a comprehensive overview of existing solutions for integrating reinforcement in digital concrete technologies, particularly focusing on 3D concrete printing. The research emphasizes on the technological aspects of the integration process, introducing a generic classification and process description framework, highlighting that reinforcement integration typically occurs separately from concrete shaping. In 3DCP approaches, however, reinforcement can be integrated as part of a single-step AM process during concrete shaping.

CEMENT & CONCRETE COMPOSITES (2021)

添加到收藏夹

Article Construction & Building Technology

Fiber orientation effects on ultra-high performance concrete formed by 3D printing

Arun R. Arunothayan et al.

Summary: This study quantitatively investigated the orientation distribution of steel fibers in 3D printed ultra-high performance concrete, revealing that smaller nozzle size and higher fiber volume fraction significantly improved fiber alignment parallel to printing direction, resulting in superior mechanical performance of the printed specimens compared to mold-cast specimens.

CEMENT AND CONCRETE RESEARCH (2021)

添加到收藏夹

Article Construction & Building Technology

3D-printable engineered cementitious composites (3DP-ECC): Fresh and hardened properties

Kequan Yu et al.

Summary: The research focuses on developing a printable cement composite material to replace steel reinforcement for 3D concrete printing. Results show that the interface between printed layers is strengthened by a groove-tongue joint, improving the strength of the printed structure.

CEMENT AND CONCRETE RESEARCH (2021)

添加到收藏夹

Article Construction & Building Technology

3D printing of mortar with continuous fibres: Principle, properties and potential for application

Jean-Francois Caron et al.

Summary: This article introduces a novel technology for enhancing 3D printed structures - the Flow-Based Pultrusion (FBP), which, by strictly controlling the rheological behavior of the cementitious matrix, achieves the routing and impregnation of thin fibers, resulting in Anisotropic Concrete, providing new possibilities for enhanced strength and ductility in hardened material.

AUTOMATION IN CONSTRUCTION (2021)

添加到收藏夹

Article Construction & Building Technology

Mesh reinforcing method for 3D Concrete Printing

Taylor Marchment et al.

AUTOMATION IN CONSTRUCTION (2020)

添加到收藏夹

Article Engineering, Multidisciplinary

Mechanical improvement of continuous steel microcable reinforced geopolymer composites for 3D printing subjected to different loading conditions

Zhijian Li et al.

COMPOSITES PART B-ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

Strength and ductility enhancement of 3D printing structure reinforced by embedding continuous micro-cables

Zhijian Li et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Construction & Building Technology

Mechanical anisotropy of aligned fiber reinforced composite for extrusion-based 3D printing

Guowei Ma et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Mechanical properties and deformation behaviour of early age concrete in the context of digital construction

Biranchi Panda et al.

COMPOSITES PART B-ENGINEERING (2019)

添加到收藏夹

Article Construction & Building Technology

Textile-to-mortar bond behaviour in lime-based textile reinforced mortars

Ali Dalalbashi et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

添加到收藏夹

Article Green & Sustainable Science & Technology

Rheology and buildability of sustainable cement-based composites containing micro-crystalline cellulose for 3D-printing

Wu-Jian Long et al.

JOURNAL OF CLEANER PRODUCTION (2019)

添加到收藏夹

Article Construction & Building Technology

Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing

R. J. M. Wolfs et al.

CEMENT AND CONCRETE RESEARCH (2018)

添加到收藏夹

Article Construction & Building Technology

Rheological requirements for printable concretes

Nicolas Roussel

CEMENT AND CONCRETE RESEARCH (2018)

添加到收藏夹

Article Construction & Building Technology

Digital in situ fabrication - Challenges and opportunities for robotic in situ fabrication in architecture, construction, and beyond

Jonas Buchli et al.

CEMENT AND CONCRETE RESEARCH (2018)

添加到收藏夹

Review Engineering, Multidisciplinary

Additive manufacturing (3D printing): A review of materials, methods, applications and challenges

Tuan D. Ngo et al.

COMPOSITES PART B-ENGINEERING (2018)

添加到收藏夹

Article Engineering, Multidisciplinary

Fiber-to-mortar bond behavior in TRM composites: Effect of embedded length and fiber configuration

Ali Dalalbashi et al.

COMPOSITES PART B-ENGINEERING (2018)

添加到收藏夹

Article Construction & Building Technology

Improving flexural characteristics of 3D printed geopolymer composites with in-process steel cable reinforcement

Jian Hui Lim et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Printable properties of cementitious material containing copper tailings for extrusion based 3D printing

Guowei Ma et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing

Biranchi Panda et al.

CEMENT & CONCRETE COMPOSITES (2018)

添加到收藏夹

Article Chemistry, Physical

Experimental Exploration of Metal Cable as Reinforcement in 3D Printed Concrete

Freek P. Bos et al.

MATERIALS (2017)

添加到收藏夹

Article Construction & Building Technology

Experimental research on bending performance of structural cable

Zhihua Chen et al.

CONSTRUCTION AND BUILDING MATERIALS (2015)

添加到收藏夹

Article Construction & Building Technology

Developments in construction-scale additive manufacturing processes

S. Lim et al.

AUTOMATION IN CONSTRUCTION (2012)

添加到收藏夹

Article Acoustics

Determination of the axial force on stay cables accounting for their bending stiffness and rotational end restraints by free vibration tests

Marcelo A. Ceballos et al.

JOURNAL OF SOUND AND VIBRATION (2008)

添加到收藏夹

Article Acoustics

Dynamic analysis of large-diameter sagged cables taking into account flexural rigidity

YQ Ni et al.

JOURNAL OF SOUND AND VIBRATION (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.