☆ 4.7 Article

Damage analysis of deployable thin-walled composite shell structure during coiling up

THIN-WALLED STRUCTURES (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Acoustics

Nonlinear dynamic modeling of bistable variable stiffness composite laminates

P. M. Anilkumar et al.

Summary: In this research, a novel semi-analytical model is proposed to predict the non-linear dynamic characteristics of bistable variable stiffness (VS) laminates. The model effectively describes the dynamic behavior of laminates during snap-through process using Foppl von Karman kinematics and an efficient energy formulation. The accuracy of the model is verified through comparison with finite element analysis and experimental results. A parametric study is conducted to investigate the effect of different fiber alignments on the dynamic characteristics.

JOURNAL OF SOUND AND VIBRATION (2023)

添加到收藏夹

Article Mechanics

Negative stiffness and buffering characteristics analysis of bistable laminates with initial curing curvature

Min Sun et al.

Summary: In this study, the influence of initial curing curvature on the negative stiffness and buffering characteristics of bistable laminates was analyzed. A geometric nonlinear finite element model was developed and verified through experimental comparison. The model was then used to investigate the effects of initial curing curvature on mechanical characteristics and buffering characteristics. The study found that adjusting the initial curing curvature can design the snap load and negative stiffness extremum, adjust the strain energy difference, and enhance the buffering range and efficiency of the laminate.

COMPOSITE STRUCTURES (2023)

添加到收藏夹

Article Engineering, Civil

Modelling localised progressive failure of composite sandwich panels under in-plane compression

Yuan Chen et al.

Summary: This study develops a finite element analysis (FEA) model for accounting localised progressive failure of carbon fibre reinforced polymer (CFRP) composite sandwich panels when subjected to in-plane compression. Good agreements between the FEA and experimental results were observed for all three types of crushing scenarios. The study sets a foundation for the future design and development of protective structures or equipment with high energy-absorption capabilities.

THIN-WALLED STRUCTURES (2023)

添加到收藏夹

Review Engineering, Aerospace

Design and application of solar sailing: A review on key technologies

Pengyuan Zhao et al.

Summary: Solar sail technology has great potential in space explorations due to its advantages of low launch cost, no-propellant consumption, and continuous thrust. Significant progress has been made in the past few decades in the structural design, manufacturing, materials, orbit transfer, and stability control of solar sails. However, there are still challenges and problems to be solved. This paper summarizes the research schemes and potential applications of solar sailing in space missions, providing an overall perspective for researchers in this field.

CHINESE JOURNAL OF AERONAUTICS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of resin-rich areas on failure behavior of unidirectional CFRP under transverse pure shear

Xiaofei Pang et al.

Summary: Fiber reinforced composites are widely used in modern aerospace and industrial equipment due to their high specific strength, specific stiffness and designability. However, controlling the consistency of preparation and molding process is difficult, resulting in large and complex dispersion of mechanical behavior. This conservative design and application limit the efficient use of fiber reinforced composites.

COMPUTATIONAL MATERIALS SCIENCE (2023)

添加到收藏夹

Article Engineering, Aerospace

Folding behavior of thin-walled tubular deployable composite boom for space applications: Experiments and numerical simulation

Tian-Wei Liu et al.

Summary: This paper investigates the folding behavior of thin-walled tubular deployable composite boom (DCB) using experimental and numerical simulation methods. DCB specimens were prepared using T700/epoxy unidirectional reinforced prepreg and a folding mechanism was designed for the folding experiments. The folding moment versus rotational displacement curves were measured and a Finite Element Model (FEM) was established to predict the folding behavior of the DCB considering different failure criteria. The research results are of great significance for the practical engineering application of the DCB.

ACTA ASTRONAUTICA (2023)

添加到收藏夹

Article Mechanics

Micro-mechanical analysis on random RVE size and shape in multiscale finite element modelling of unidirectional FRP composites

N. K. Balasubramani et al.

Summary: This study revisits the definition problem of representative volume elements (RVEs) in combined computational homogenisation-dehomogenisation procedure for estimating critical material allowables of unidirectional fiber reinforced polymer composites. By performing Monte Carlo simulation, the size and shape effects of 3D RVEs were investigated, and appropriately sized RVE models were proposed as 3D statistical volume elements.

COMPOSITE STRUCTURES (2022)

添加到收藏夹

Article Engineering, Aerospace

SIASAIL-I solar sail: From system design to on-orbit demonstration missions

Jinguo Liu et al.

Summary: Solar sails, an important passive propulsion method in deep space exploration, have attracted increasing attention. SIASAIL-I, a solar sail verification mission, successfully deployed a sail in low earth orbit using a two-stage deployment system. This paper introduces the design process and ground experiments of SIASAIL-I, providing engineering experience for the development of solar sails.

ACTA ASTRONAUTICA (2022)

添加到收藏夹

Article Materials Science, Composites

Identification of RVE length scale in fiber composites via combined optical and SEM digital image correlation

Behrad Koohbor et al.

Summary: This study developed a multiscale experimental approach combining optical and SEM DIC measurements to experimentally characterize the length scale of the RVE in a carbon fiber composite with a random fiber distribution. The RVE size was determined by the convergence between locally averaged strains and global strains, and it was found to be stress dependent and increased with the evolution of internal damage in the composite.

COMPOSITES SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Civil

Twisting control strategy of bistable composite shell with initial curvature

Yanqi Li et al.

Summary: This paper proposes a method to control the twisting of bistable composite shells by introducing an adjustive angle, and develops an analytical model to capture the suitable adjustive angle. The analytical model considers various factors that influence the adjustive angle, and the analytical predictions are verified by experiments and finite element results. This has guiding significance for designing bistable composite structures without twisting.

THIN-WALLED STRUCTURES (2022)

添加到收藏夹

Article Mechanics

Folding behaviour of a deployable composite cabin for space habitats-part 1: Experimental and numerical investigation

Tian -Wei Liu et al.

Summary: This paper proposes a deployable composite cabin (DCC) and verifies its effectiveness and feasibility through experimental and numerical simulation. The study shows that the DCC can achieve folding and deployment functions through elastic deformation.

COMPOSITE STRUCTURES (2022)

添加到收藏夹

Article Engineering, Aerospace

Viscoelastic characterization of polymers for deployable composite booms

Jin Ho Kang et al.

Summary: The study evaluated the viscoelastic properties of candidate commercial polymers for deployable boom structures of solar sails. Results showed that a bismaleimide (BMI) exhibited less stress relaxation compared to the baseline novolac epoxy, leading to a 44% improvement in resistance to relaxation in carbon fiber composites fabricated with the BMI resin.

ADVANCES IN SPACE RESEARCH (2021)

添加到收藏夹

Article Mechanics

Failure analysis of thin-walled composite structures using independent advanced damage models

P. Rozylo

Summary: The study aimed to present the complex phenomenon of damage in thin-walled composite structures under axial compression, using actual structures prepared with CFRP composite and conducting research until construction damage occurred. Experimental testing recorded post-critical equilibrium paths and acoustic emission signals, while numerical simulations used progressive fracture analysis (PFA) and cohesive zone model (CZM) to assess load capacity loss and demonstrate delamination. The research effectively showed the influence of axial compression on post-critical behavior and damage phases of the structure.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

A novel multiscale modeling strategy of the low-velocity impact behavior of plain woven composites

Yuliang Hou et al.

Summary: A novel multiscale modeling strategy is proposed to investigate the low-velocity impact behavior of plain woven composites. The study predicts damage initiation and evolution under various loading conditions at micro and mesoscale levels. Numerical simulations confirm delamination and matrix-based damages as prevailing failure modes.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

A theoretical and experimental assessment of 3D macroscopic failure criteria for predicting pure inter-fiber fracture of transversely isotropic UD composites

Jiefei Gu et al.

Summary: In this study, popular 3D macroscopic failure criteria for predicting pure inter-fiber fracture of transversely isotropic unidirectional composites were systematically and comprehensively assessed. Results showed that the action-plane based criteria performed best in qualitatively describing failure responses, with performance ranking varying for different material types and none able to accurately predict failure stresses in all loading conditions. The evaluated criteria's main advantages and shortcomings were identified and summarized using a combined theoretical and experimental analysis approach.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

Examination of selected failure criteria with asymmetric shear stresses in the collapse analysis of laminated shells

J. Chroscielewski et al.

Summary: The paper discusses how to consider the asymmetry caused by drilling rotation when analyzing the failure of composite shells using the nonlinear 6-parameter shell theory. The results show that different failure criteria may result in slightly different damage zones and values of the first ply failure and ultimate load.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Article Mechanics

Comprehensive analysis of in-plane tensile characteristics of thin carbon/aramid hybrid composites using experimental and RVE- based numerical study

Sojan Andrews Zachariah et al.

Summary: This study investigates the application of woven aramid fabric with thin woven CFRP in enhancing the strain to failure behavior. Experimental tests and numerical validation were conducted to study the in-plane tensile properties of hybrid carbon/aramid polymer composites. The results showed that stacking sequences and location of high strain materials significantly influenced the primary and secondary tensile modulus, toughness, failure strains, and damage morphology.

COMPOSITE STRUCTURES (2021)

添加到收藏夹

Review Engineering, Multidisciplinary

Design and optimization of self-deployable damage tolerant composite structures: A review

P. Fernandes et al.

Summary: Composite deployable structures are gaining importance in the space industry as an alternative to traditional metallic systems, allowing for increased efficiency and applicability. By ensuring reliability, materials can be used beyond their elastic range, leading to improved designs. The possibility of combining different design approaches for deployable structures is also being discussed.

COMPOSITES PART B-ENGINEERING (2021)

添加到收藏夹

Article Engineering, Aerospace

Progressive damage behaviors of woven composite laminates subjected to LVI, TAI and CAI

Zhengqiang Cheng et al.

CHINESE JOURNAL OF AERONAUTICS (2020)

添加到收藏夹

Article Engineering, Manufacturing

An accurate and easy to implement method for predicting matrix crack and plasticity of composites with an efficient search algorithm for LaRC05 criterion

Xiaodong Wang et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2020)

添加到收藏夹

Article Engineering, Civil

Rotational stiffness of drum deployed thin-walled open tubular booms

Jason Shore et al.

THIN-WALLED STRUCTURES (2020)

添加到收藏夹

Article Materials Science, Composites

In-situ multiscale shear failure of a bistable composite tape-spring

Bing Wang et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Civil

Blossoming analysis of composite deployable booms

Sicong Wang et al.

THIN-WALLED STRUCTURES (2020)

添加到收藏夹

Review Engineering, Civil

Bistable morphing composite structures: A review

Zheng Zhang et al.

THIN-WALLED STRUCTURES (2019)

添加到收藏夹

Article Engineering, Marine

An empirical formula for predicting the collapse strength of composite cylindrical-shell structures under external pressure loads

Yoon Sik Cho et al.

OCEAN ENGINEERING (2019)

添加到收藏夹

Proceedings Paper Engineering, Industrial

Machining induced damage in orthogonal cutting of UD composites: FEA based assessment of Hashin and Puck criteria

F. Cepero-Mejias et al.

17TH CIRP CONFERENCE ON MODELLING OF MACHINING OPERATIONS (17TH CIRP CMMO) (2019)

添加到收藏夹

Article Mechanics

Computational and experimental study on dynamic instability of extended bistable carbon/epoxy booms subjected to bending

C. Wu et al.

COMPOSITE STRUCTURES (2018)

添加到收藏夹

Article Engineering, Civil

Multi-scale analysis for mechanical properties of fiber bundle and damage characteristics of 2D triaxially braided composite panel under shear loading

Hongyong Jiang et al.

THIN-WALLED STRUCTURES (2018)

添加到收藏夹

Article Engineering, Civil

An experimental and numerical study of flattening and wrapping process of deployable composite thin-walled, lenticular tubes

Wujun Chen et al.

THIN-WALLED STRUCTURES (2017)

添加到收藏夹

Article Engineering, Civil

Comparative study between XFEM and Hashin damage criterion applied to failure of composites

A. P. C. Duarte et al.

THIN-WALLED STRUCTURES (2017)

添加到收藏夹

Article Mechanics

Natural frequency optimization of braided bistable carbon/epoxy tubes: Analysis of braid angles and stacking sequences

C. Wu et al.

COMPOSITE STRUCTURES (2017)

添加到收藏夹

Article Mechanics

Some modifications of Hashin's failure criteria for unidirectional composite materials

Jiefei Gu et al.

COMPOSITE STRUCTURES (2017)

添加到收藏夹

Article Mechanics

A novel approach to impose periodic boundary condition on braided composite RVE model based on RPIM

Rongqiao Wang et al.

COMPOSITE STRUCTURES (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Multi-scale structure modeling of damage behaviors of 3D orthogonal woven composite materials subject to quasi-static and high strain rate compressions

Yumin Wan et al.

MECHANICS OF MATERIALS (2016)

添加到收藏夹

Article Engineering, Multidisciplinary

Failure analysis of fiber-reinforced composite laminates subjected to biaxial loads

Hsuan-Teh Hu et al.

COMPOSITES PART B-ENGINEERING (2015)

添加到收藏夹

Article Mechanics

Coiling dynamic analysis of thin-walled composite deployable boom

A. Stabile et al.

COMPOSITE STRUCTURES (2014)

添加到收藏夹

Article Materials Science, Composites

Compressive failure of UD-CFRP containing void defects: In situ SEM microanalysis

Julia Hapke et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2011)

添加到收藏夹

Article Engineering, Manufacturing

Neutrally stable behavior in fiber-reinforced composite tape springs

Marc R. Schultz et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

A continuum damage model for composite laminates:: Part I -: Constitutive model

P. Maimi et al.

MECHANICS OF MATERIALS (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

A continuum damage model for composite laminates:: Part II -: Computational implementation and validation

P. Maimi et al.

MECHANICS OF MATERIALS (2007)

添加到收藏夹

Article Multidisciplinary Sciences

Analytical models for bistable cylindrical shells

SD Guest et al.

PROCEEDINGS OF THE ROYAL SOCIETY A-MATHEMATICAL PHYSICAL AND ENGINEERING SCIENCES (2006)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.