☆ 4.7 Article

An FFT-based homogenization scheme for cohesive zones with an application to adhesives and the core material of thin metal sandwich plates

THEORETICAL AND APPLIED FRACTURE MECHANICS (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Mechanical

Novel mode III DCB test setups and related evaluation methods to investigate the fracture behaviour of adhesive joints

Peer Schrader et al.

Summary: Two test setups are proposed for determining the critical mode III energy release rate (ERR) of adhesive joints. Nonlinear elastic fracture mechanics (J-integral) and linear elastic fracture mechanics (Irwin-Kies equation) are used for data evaluation. Crack length and process zone length are measured using backface strain measurements. The results show that the J-integral evaluation method is the most reliable for determining the mode III fracture energy.

THEORETICAL AND APPLIED FRACTURE MECHANICS (2023)

添加到收藏夹

Article Mechanics

Experimental determination of coupled cohesive laws with an unsymmetrical stiffness matrix for structural adhesive joints loaded in mixed-mode I plus III

Stephan Marzi

Summary: This manuscript presents a novel strategy to identify cohesive laws in mixed-mode I+III directly from experimental data. However, due to the physical behavior of adhesives, certain requirements for obtaining a constitutive law in mixed-mode cannot be fulfilled, which can be viewed as a disadvantage of the proposed method.

ENGINEERING FRACTURE MECHANICS (2023)

添加到收藏夹

Article Engineering, Multidisciplinary

Adaptation and validation of FFT methods for homogenization of lattice based materials

S. Lucarini et al.

Summary: An FFT framework suitable for lattice based materials is proposed and evaluated for its performance compared to FEM solutions. The adapted Galerkin approach combined with Voigt surface smoothening was found to be the best FFT framework in terms of accuracy, numerical efficiency, and h-convergence. FFT becomes competitive with FEM in terms of numerical efficiency for cells with relative densities above approximately 7%.

COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2022)

添加到收藏夹

Article Mechanics

A computationally efficient approach for generating RVEs of various inclusion/fibre shapes

Rajesh Nakka et al.

Summary: A computationally efficient method for generating virtual periodic representative volume element (RVE) is developed, capable of handling arbitrary inclusion shapes. A universal collision/overlap detection and repair method is proposed to remove inclusion overlaps. The generated RVEs are evaluated using statistical metrics, confirming the random distribution of inclusions. Effective properties of RVEs are determined using homogenization with various fibre cross-section shapes.

COMPOSITE STRUCTURES (2022)

添加到收藏夹

Article Engineering, Multidisciplinary

Voxel-based finite elements with hourglass control in fast Fourier transform-based computational homogenization

Matti Schneider

Summary: The power of fast Fourier transform (FFT)-based methods in computational micromechanics depends on the seamless integration of discretization scheme and solution method. Different discretization schemes have their advantages and disadvantages, and the rotated staggered grid discretization is widely used but has its own downsides. This article introduces FFT-based solution techniques for underintegrated trilinear finite elements with hourglass control, which stabilizes the convergence behavior, removes checkerboards, and allows for a softer material response compared to fully integrated elements.

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2022)

添加到收藏夹

Article Mechanics

Integral nonlocal approach to model interface decohesion in FFT solvers

L. Sharma et al.

Summary: The work extends the capability of Fast Fourier transform (FFT) solvers to interface damage modelling, incorporating the cohesive fracture concept using continuum damage mechanics and approximating sharp interfaces as interphases. Anisotropic kinematics are used to model interface crack opening and sliding, with discussions on decohesion model and nonlocal regularization within the interphases. Integral nonlocal approach is utilized to achieve delocalized deformation and scaling of cohesive parameters, with one-dimensional study on overall response and insensitivity of dissipation to interphase thickness, as well as crack propagation modelling in two-dimensional polycrystals.

ENGINEERING FRACTURE MECHANICS (2021)

添加到收藏夹

Review Mechanics

A review of nonlinear FFT-based computational homogenization methods

Matti Schneider

Summary: Computational homogenization methods based on FFT have become popular for complex microstructures, with improved understanding leading to broader applications and advancements in the original approach.

ACTA MECHANICA (2021)

添加到收藏夹

Article Mathematics, Interdisciplinary Applications

FFT phase-field model combined with cohesive composite voxels for fracture of composite materials with interfaces

Yang Chen et al.

Summary: The proposed damage modeling framework based on the FFT method combines the variational phase-field approach with a cohesive zone model, enabling effective application in composite materials with interfaces to predict complex fracture behaviors in composite microstructures.

COMPUTATIONAL MECHANICS (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

An FFT framework for simulating non-local ductile failure in heterogeneous materials

M. Magri et al.

Summary: This paper presents a new algorithm for simulating gradient ductile damage, which effectively addresses issues in the spatial discretization of continuum ductile damage models. By iteratively solving the mechanical problem and the Helmhotz-type equation separately, the algorithm successfully simulates the failure process of complex 3D particle reinforced composites.

COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

The J-integral for mixed-mode loaded cracks with cohesive zones

Johannes Scheel et al.

Summary: The J-integral and CTOD quantify the loading at the crack tip, with their equivalence depending on the constitutive law of the cohesive zone. A J-integral vector for mixed-mode loaded cracks is derived based on the cohesive zone approach in this paper.

INTERNATIONAL JOURNAL OF FRACTURE (2021)

添加到收藏夹

Article Mathematics, Interdisciplinary Applications

An FFT-based spectral solver for interface decohesion modelling using a gradient damage approach

L. Sharma et al.

COMPUTATIONAL MECHANICS (2020)

添加到收藏夹

Article Engineering, Multidisciplinary

Fast implicit solvers for phase-field fracture problems on heterogeneous microstructures

Felix Ernesti et al.

COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2020)

添加到收藏夹

Article Mechanics

A DIC method to determine the Mode I energy release rate G, the J integral and the traction -separation law simultaneously for adhesive joints

F. Sun et al.

ENGINEERING FRACTURE MECHANICS (2020)

添加到收藏夹

Article Mathematics, Interdisciplinary Applications

On the accuracy of spectral solvers for micromechanics based fatigue modeling

S. Lucarini et al.

COMPUTATIONAL MECHANICS (2019)

添加到收藏夹

Article Engineering, Chemical

Comparison of J-integral methods to experimentally determine cohesive laws in shear for adhesives

Anders Biel et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

A FFT solver for variational phase-field modeling of brittle fracture

Yang Chen et al.

COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

On the Barzilai-Borwein basic scheme in FFT-based computational homogenization

Matti Schneider

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2019)

添加到收藏夹

Article Materials Science, Composites

Measuring Fiber Orientation of Elliptical Fibers from Optical Microscopy

Nathan D. Sharp et al.

JOURNAL OF COMPOSITES SCIENCE (2019)

添加到收藏夹

Article Mechanics

A quantitative assessment of the scale separation limits of classical and higher-order asymptotic homogenization

M. M. Ameen et al.

EUROPEAN JOURNAL OF MECHANICS A-SOLIDS (2018)

添加到收藏夹

Article Engineering, Chemical

An Out-of-plane Loaded Double Cantilever Beam (ODCB) test to measure the critical energy release rate in mode III of adhesive joints

Lukas Loh et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2018)

添加到收藏夹

Article Mechanics

Modelling the microstructure and computing effective elastic properties of sand core materials

Matti Schneider et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2018)

添加到收藏夹

Review Materials Science, Multidisciplinary

Generation of 3D representative volume elements for heterogeneous materials: A review

Swantje Bargmann et al.

PROGRESS IN MATERIALS SCIENCE (2018)

添加到收藏夹

Review Computer Science, Interdisciplinary Applications

A review of predictive nonlinear theories for multiscale modeling of heterogeneous materials

Karel Matous et al.

JOURNAL OF COMPUTATIONAL PHYSICS (2017)

添加到收藏夹

Article Engineering, Multidisciplinary

Computational homogenization of elasticity on a staggered grid

Matti Schneider et al.

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2016)

添加到收藏夹

Article Mechanics

Automated analysis of microstructural effects on the failure response of heterogeneous adhesives

Soheil Soghrati et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2016)

添加到收藏夹

Proceedings Paper Engineering, Mechanical

Cohesive zone modelling and the fracture process of structural tape

Ulf Stigh et al.

21ST EUROPEAN CONFERENCE ON FRACTURE, (ECF21) (2016)

添加到收藏夹

Article Mechanics

Formulation of nonlocal damage models based on spectral methods for application to complex microstructures

Martin Boeff et al.

ENGINEERING FRACTURE MECHANICS (2015)

添加到收藏夹

Article Engineering, Multidisciplinary

Hierarchically parallel coupled finite strain multiscale solver for modeling heterogeneous layers

Matthew Mosby et al.

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2015)

添加到收藏夹

Article Mathematics, Interdisciplinary Applications

Efficient fixed point and Newton-Krylov solvers for FFT-based homogenization of elasticity at large deformations

Matthias Kabel et al.

COMPUTATIONAL MECHANICS (2014)

添加到收藏夹

Article Computer Science, Interdisciplinary Applications

Automated modeling of random inclusion composites

M. Bailakanavar et al.

ENGINEERING WITH COMPUTERS (2014)

添加到收藏夹

Proceedings Paper Engineering, Mechanical

Adhesive tapes; cohesive laws for a soft layer

Anders Biel et al.

20TH EUROPEAN CONFERENCE ON FRACTURE (2014)

添加到收藏夹

Article Engineering, Chemical

Modelling adhesive joints with cohesive zone models: effect of the cohesive law shape of the adhesive layer

R. D. S. G. Campilho et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2013)

添加到收藏夹

Article Engineering, Chemical

A straightforward method to obtain the cohesive laws of bonded joints under mode I loading

M. F. S. F. de Moura et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2012)

添加到收藏夹

Article Engineering, Multidisciplinary

Coupled multi-scale cohesive modeling of failure in heterogeneous adhesives

M. G. Kulkarni et al.

INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2010)

添加到收藏夹

Article Mechanics

Computational multiscale modelling of heterogeneous material layers

C. B. Hirschberger et al.

ENGINEERING FRACTURE MECHANICS (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Multi-scale modeling of heterogeneous adhesives: Effect of particle decohesion

Mohan G. Kulkarni et al.

MECHANICS OF MATERIALS (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Multiscale cohesive failure modeling of heterogeneous adhesives

Karel Matous et al.

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2008)

添加到收藏夹

Article Mechanics

Representative volume: Existence and size determination

I. M. Gitman et al.

ENGINEERING FRACTURE MECHANICS (2007)

添加到收藏夹

Article Engineering, Electrical & Electronic

The design and implementation of FFTW3

M Frigo et al.

PROCEEDINGS OF THE IEEE (2005)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.