☆ 4.7 Article

Cavitation erosion resistance and tribological performance of PAI/PI/EP soft coating on 20CrMo

WEAR (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Investigations of CrN+Cr2O3/TiO2 coatings obtained in a PVD/ALD hybrid method on austenitic 316L steel substrate

Marcin Staszuk

Summary: This study investigated hybrid coatings of CrN + Cr2O3/TiO2 type obtained using the hybrid PVD/ALD technology on a Cr-Ni-Mo (316L) stainless steel substrate. The coatings were tested for their structural, electrochemical, tribological properties, and adhesion to the substrate. The results showed that the electrochemical properties and corrosion resistance of the coatings were significantly improved under specific deposition conditions.

VACUUM (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Simultaneous enhancement of strength and ductility in a medium carbon low-alloy steel induced by secondary martensite and Cu-rich particles

X. X. Dong et al.

Summary: This study aims to improve both the strength and ductility of a medium carbon low-alloy steel by adding Cu and conducting the partitioning treatment. The microstructure obtained consisted of temper martensite, retained austenite, M-A islands/secondary martensite, bainitic ferrite, and nanosized Cu-rich particles. The partitioning temperature significantly influenced the microstructure, leading to distinct variations in mechanical properties. The increase in partitioning temperature from 240°C to 380°C resulted in a decrease in yield strength from 1470 MPa to 1110 MPa, while the ultimate tensile strength gradually decreased from 2300 MPa to 1440 MPa. However, the ductility significantly increased from 9% to 26% with the increasing partitioning temperature. The formation of numerous nanosized Cu-rich particles in the temper martensite contributed to the simultaneous increase in yield strength and ductility.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

添加到收藏夹

Article Acoustics

Cavitation bubble structures below a soft boundary in an ultrasonic field

Fan Li et al.

Summary: We investigated the layer structure of bubbles beneath water/air and water/EPE interfaces using high-speed photography. The structure was formed by floating spherical clusters, derived from bubble nuclei attaching at the interface, bubbles floating in the liquid, or bubbles generated on the transducer surface. The shape of the boundary influenced the layer structure, which appeared similar below the water/EPE interface. A simplified model of bubble column and chain was developed to describe interface impacts and bubble interaction in a branching structure. The resonant frequency of bubbles was found to be lower than that of isolated single bubbles, and the primary acoustic field played a significant role in structure generation. Higher acoustic frequency and pressure decreased the distance between the structure and the interface. In low-frequency intense inertial cavitation fields (28 and 40 kHz), a hat-like layer structure of bubbles was more likely to exist, with violent bubble oscillation. On the other hand, structures composed of discrete spherical clusters were more likely to form in relatively weak cavitation fields at 80 kHz, where stable and inertial cavitation coexisted. The theoretical predictions were consistent with experimental observations.

ULTRASONICS SONOCHEMISTRY (2023)

添加到收藏夹

Article Polymer Science

The Tribological and Mechanical Properties of PI/PAI/EP Polymer Coating under Oil Lubrication, Seawater Corrosion and Dry Sliding Wear

Shijie Yu et al.

Summary: The tribological performance of a copper alloy engine bearing under oil lubrication, seawater corrosion, and dry sliding wear was investigated. Three different PI/PAI/EP coatings with varying amounts of Ce2O3 were designed and prepared using a liquid spraying process. The tribological properties of these coatings were tested under different working conditions. The results showed that the hardness of the coating decreased with the addition of Ce2O3 due to the agglomeration of Ce2O3. The wear amount of the coating initially increased and then decreased with the increase of Ce2O3 content under dry sliding wear. Under seawater corrosion, the wear resistance of the coating decreased with the increase of Ce2O3 content. The coating with 1.5 wt% Ce2O3 exhibited the best wear resistance. Under oil lubrication conditions, the coating showed stable frictional coefficient and good lubrication and protection effect of the lubricating oil film.

POLYMERS (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Design of High-Entropy Alloy Coating for Cavitation Erosion Resistance by Different Energy-Induced Dynamic Cyclic Behaviors

Haobo Cao et al.

Summary: An anti-cavitation erosion (CE) coating with single face-centered cubic (FCC) structure was designed to absorb both mechanical impact energy and thermal energy released by bubble collapse, effectively avoiding excessive crystal defects and exhibiting a CE resistance 2 times better than the classical coating.

ACS APPLIED MATERIALS & INTERFACES (2023)

添加到收藏夹

Article Chemistry, Physical

Microstructure, mechanical properties and corrosion behavior of Ce doped TiN films

Lei Fan et al.

Summary: TiN films doped with Ce show increased hardness and elastic modulus with higher Ce content, but the film structure becomes amorphous when Ce content reaches 14.19 at.%. The substitution of Ce atoms for Ti atoms leads to an increase in cell volume and grain refinement.

APPLIED SURFACE SCIENCE (2022)

添加到收藏夹

Article Chemistry, Physical

Three Tribolayers Self-Generated from SiC Individually Work for Reducing Friction in Different Contact Pressures

Yusuke Ootani et al.

Summary: This study reveals that the low friction in SiC/water systems is a result of the synergistic effects of self-forming silica-based, silica hydrate, and amorphous carbon tribolayers. These tribolayers play different roles in reducing friction in different contact pressure areas.

JOURNAL OF PHYSICAL CHEMISTRY C (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Cavitation-erosion behavior and mechanism of high-velocity oxygen-fuel sprayed CuAlNiTiSi medium-entropy alloy coating

Jie Cheng et al.

Summary: This paper presents the fabrication and characterization of a novel Cu55Al20Ni12Ti8Si5 medium-entropy alloy (MEA) coating. The coating exhibited excellent corrosion resistance, which can be attributed to its unique microstructure and superior mechanical properties.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Expanded Polytetrafluoroethylene/Mxene Nanosheet Composites with Hydrophilicity and Lipophilicity for Purification of Oil Spills and Wastewater

Ya Liu et al.

Summary: In this study, ePTFE/Mxene nanosheet composites with nanoscale double pore structures were constructed, which improved the hydrophilicity, oil absorption capacity, and oil-water separation performance of the material. The ePTFE/Mxene composites showed potential for practical applications in oil spill remediation and water separation/remediation.

ACS APPLIED NANO MATERIALS (2022)

添加到收藏夹

Article Energy & Fuels

Observation of the Formation of Multiple Shock Waves at the Collapse of Cavitation Bubbles for Improvement of Energy Convergence

Marc Tinguely et al.

Summary: In this study, the formation of multiple shock waves generated by the collapse of a laser-induced bubble was investigated using high-speed imaging technology. The results showed that there is a certain sequence in the generation process of these shock waves.

ENERGIES (2022)

添加到收藏夹

Article Engineering, Mechanical

Synergetic effects of biomimetic microtexture with multi-solid lubricants to improve tribological properties of AISI 4140 steel

Qipeng Huang et al.

Summary: Inspired by tree frog toes, a control mechanism using regular hexagonal microtexture and SnAgCu-TiC lubricants was applied to the tooth surface of slewing bearing, resulting in a significantly reduced coefficient of friction. Antifriction was achieved as SnAgCu wrapped around nano-TiC to form tribofilms with submicron rollers.

TRIBOLOGY INTERNATIONAL (2022)

添加到收藏夹

Review Materials Science, Multidisciplinary

Tribology of SiC ceramics under lubrication: Features, developments, and perspectives

Wei Zhang

Summary: This paper reviews the features and developments of tribology of SiC ceramics under lubrication, and discusses comprehensively the strategies to enhance their tribological performance. It also presents the tribochemical reactions and Stribeck curves of SiC ceramics, and proposes future research directions in the field of tribology under lubrication.

CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE (2022)

添加到收藏夹

Article Engineering, Marine

Experimental study on the characteristics of microjets and shock waves of cavitation bubbles near elastic boundaries

Yanwei Zhai et al.

Summary: This paper studies the interaction between cavitation bubbles and different elastic boundaries from the perspective of microjets and shock waves. The elastic deformation characteristics of elastic materials under the penetration of microjets are found to be the main influencing factors of cavitation erosion.

OCEAN ENGINEERING (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Preparation of Ni-P-Ti3C2Tx-Ce composite coating with enhanced wear resistance and electrochemical corrosion behavior on the surface of low manganese steel

Lunliang Zhang et al.

Summary: Ti3C2Tx-Ce powders were successfully synthesized and incorporated into the Ni-P coating, resulting in the Ni-P-Ti3C2Tx-Ce composite coating. The composite coating showed improved wear resistance and corrosion resistance compared to the Ni-P coating.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Mechanical

Microstructure and cavitation erosion resistance of arc ion plating NiCrAlY coating on the 304L stainless steel

Zhengliang Liu et al.

Summary: The NiCrAlY coating fabricated on the 304L stainless steel substrate by arc ion plating can significantly improve the ultrasonic cavitation erosion resistance, with coatings fabricated at higher bias showing the best performance. The study also found that some micro-pores can enhance the elastic recovery ability of the coating.

TRIBOLOGY INTERNATIONAL (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Tribological performance and behaviour of CVD TiC/TiCN/TiN multilayer coating at elevated temperature

Shao-Long Wang et al.

Summary: The TiC/TiCN/TiN multilayer coating was prepared on a high-speed tool steel W6Mo5Cr4V2 by chemical vapour deposition, and its tribological performance was investigated at 400-600 degrees Celsius. Results show that the friction coefficient of the coating decreases initially before increasing again with temperature, while the average wear rate increases continuously. The presence of Fe(2)O(3) in the tribo-oxidative layer contributes to a reduction in the coating's friction coefficient but an increase in wear rate.

SURFACE ENGINEERING (2021)

添加到收藏夹

Article Materials Science, Ceramics

Effect of WC-10Co on cavitation erosion behaviors of AlCoCrFeNi coatings prepared by HVOF spraying

Zheng Wei et al.

Summary: The (AlCoCrFeNi)1-X(WC-10Co)X composite coatings were fabricated by HVOF spraying and showed improved cavitation erosion resistance with the addition of WC-10Co. The cavitation erosion damage was concentrated on the interface in the initial stage of testing, but the presence of WC-10Co below the HEA region improved the overall impact resistance of the coating.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Chemistry, Physical

Time-dependent corrosion behavior of electroless Ni-P coating in H2S/Cl- environment

Longyi Li et al.

Summary: The study found that the Ni-P coating can significantly reduce the corrosion rate of steel pipes, forming a dense protective film. However, there is still a problem of severe local corrosion of the substrate during prolonged corrosion testing.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of plasma carbonitriding on the high-temperature tribological properties of a TiAlCrN coating on 300M steel by multi-arc ion plating

Shiwei Zuo et al.

Summary: In this research, a duplex treatment consisting of plasma carbonitriding and multi-arc ion plating was utilized to enhance the high-temperature tribological properties of TiAlCrN coatings on 300M steel. The TiAlCrN coating exhibited improved adhesion and tribological performance due to the gradient hardness support, good chemical composition gradient and diffusion effect during the carbonitriding process. Various characterization techniques were employed to study the microstructure, element composition and structural variations of the composite coating.

PHILOSOPHICAL MAGAZINE (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

High temperature friction and wear performance of TiB2-50Ni composite coating sprayed by HVOF technique

Yueming Wang et al.

Summary: The study investigated the effect of temperature on the friction and wear properties of TiB2-50Ni coatings, showing that the TiB2-50Ni coatings exhibit superior performance at high temperatures with main wear mechanisms being abrasive wear, adhesion wear, and oxidation wear. Comparing to 304 stainless steel matrix, the TiB2-50Ni composite coating demonstrates better high temperature friction and wear properties.

SURFACE & COATINGS TECHNOLOGY (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Bubble behavior in cylindrical and square vessels under centric mechanical stirring

Kun Wang et al.

Summary: Water model experiments were conducted to investigate bubble behavior under centric mechanical stirring in cylindrical and square vessels. The results showed that centric mechanical stirring in the square vessel was suitable for breaking and dispersing bubbles, while not suitable for that in the cylindrical vessel. Increasing impeller blade length and rotation speed helped to disintegrate and disperse bubbles widely.

JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2021)

添加到收藏夹

Article Engineering, Mechanical

Effects of Cu and WS2 addition on microstructural evolution and tribological properties of self-lubricating anti-wear coatings prepared by laser cladding

Jianhui Yuan et al.

Summary: High manganese steel components coated with NiCr/TiC or NiCr/TiC-Cu-WS2 using laser cladding technology exhibit improved hardness and wear resistance. The addition of Cu reduces wear loss, while the synergistic lubrication of Cu, CrS, and WS2 significantly enhances wear resistance. Overall, laser clad self-lubricating anti-wear coatings show promising tribological performance.

TRIBOLOGY INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

Electrochemical noise analysis of cavitation erosion corrosion resistance of NbC nanocrystalline coating in a 3.5 wt% NaCl solution

Shuang Peng et al.

Summary: The study revealed that the NbC coating exhibited better cavitation erosion-corrosion resistance compared to the Ti-6Al-4V alloy, with the noise resistance and slope values of the NbC coating remaining almost constant regardless of the output power. The charge of the corrosion event and the total energy of the d series crystals for the NbC coating were significantly lower than that of the Ti-6Al-4V alloy, indicating a high propensity of pitting corrosion for the alloy.

SURFACE & COATINGS TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

Effect of N plus Cr ions implantation on corrosion and tribological properties in simulated seawater of carburized alloy steel

Shengqiang Song et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

The coupling effect of immersion corrosion and cavitation erosion of NiCoCrAlYTa coatings in artificial seawater

Enkang Hao et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Engineering, Mechanical

Effect of surface microtexturing on seawater-lubricated contacts under starved and fully-flooded conditions

Reza Gheisari et al.

TRIBOLOGY INTERNATIONAL (2020)

添加到收藏夹

Article Engineering, Mechanical

In-situ fabricated bulk metallic glass/graphite composites with a 3D lubricating layer: Tribological properties under dry sliding and in seawater

Xiaofang Jiang et al.

TRIBOLOGY INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Cavitation erosion behavior of ceramic/organic coatings exposed to artificial seawater

Wen Deng et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Structural and morphological evaluation of layered WS2 thin films

I Hotovy et al.

VACUUM (2020)

添加到收藏夹

Article Chemistry, Physical

Friction reduction of water based lubricant with highly dispersed functional MoS2 nanosheets

Yongxia Wang et al.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Unraveling the effects of CO2 and H2S on the corrosion behavior of electroless Ni-P coating in CO2/H2S/Cl- environments at high temperature and high pressure

Chong Sun et al.

CORROSION SCIENCE (2019)

添加到收藏夹

Article Engineering, Mechanical

Tribocorrosion behaviors of thermal spraying WC/Ni60 coated 316L stainless steel in artificial seawater

Eryong Liu et al.

INDUSTRIAL LUBRICATION AND TRIBOLOGY (2019)

添加到收藏夹

Article Engineering, Mechanical

Cavitation erosion resistance enhancement of martensitic stainless steel via low-temperature plasma carburizing

F. da S. Severo et al.

WEAR (2019)

添加到收藏夹

Article Engineering, Mechanical

Comparison of the cavitation erosion and slurry erosion behavior of cobalt-based and nickel-based coatings

M. E et al.

WEAR (2019)

添加到收藏夹

Article Engineering, Mechanical

Tribological Performance Improvement of Polyamide against Steel Using Polymer Coating

Kian Bashandeh et al.

TRIBOLOGY TRANSACTIONS (2019)

添加到收藏夹

Article Engineering, Mechanical

Characterization and evolution of the coefficient of friction during pin on disc tribotest: Comparison between C10200 Cu, AA6082-T6 Al and C36000 brass pins under varying normal loads

R. O. Ferreira et al.

TRIBOLOGY INTERNATIONAL (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Optical and electrical transport properties of ZnO/MoS2 heterojunction p-n structure

Hung-Pin Hsu et al.

MATERIALS CHEMISTRY AND PHYSICS (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

Slurry Erosion Behavior of F6NM Stainless Steel and High-Velocity Oxygen Fuel-Sprayed WC-10Co-4Cr Coating

S. Y. Cui et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2017)

添加到收藏夹

Article Engineering, Chemical

Preparation, characterization, and applications of electrospun ultrafine fibrous PTFE porous membranes

Yan Huang et al.

JOURNAL OF MEMBRANE SCIENCE (2017)

添加到收藏夹

Article Materials Science, Coatings & Films

The influence of different metallic counterparts on the tribological performance of nc-CrC/GLC in seawater

Yuwei Ye et al.

SURFACE & COATINGS TECHNOLOGY (2017)

添加到收藏夹

Article Engineering, Mechanical

Effect of oil temperature and counterpart material on the wear mechanism of ta-CNx coating under base oil lubrication

Xiaoxu Liu et al.

WEAR (2017)

添加到收藏夹

Article Materials Science, Coatings & Films

Comparative tribological and corrosion resistance properties of epoxy composite coatings reinforced with functionalized fullerene C60 and graphene

Dan Liu et al.

SURFACE & COATINGS TECHNOLOGY (2016)

添加到收藏夹

Article Materials Science, Coatings & Films

Effect of nano-CeO2 on microstructure and wear resistance of Co-based coatings

Lin Ding et al.

SURFACE & COATINGS TECHNOLOGY (2015)

添加到收藏夹

Article Engineering, Mechanical

Preparation and tribological properties of polyimide/carbon sphere microcomposite films under seawater condition

Chunying Min et al.

TRIBOLOGY INTERNATIONAL (2015)

添加到收藏夹

Article Engineering, Mechanical

Enhancement of Wear and Friction Characteristics of Epoxy Resin by Multiwalled Carbon Nanotube and Boron Nitride Nanoparticles

Hayrettin Duzcukoglu et al.

TRIBOLOGY TRANSACTIONS (2015)

添加到收藏夹

Article Chemistry, Multidisciplinary

Excellent tribological and anti-corrosion performance of polyurethane composite coatings reinforced with functionalized graphene and graphene oxide nanosheets

Mengting Mo et al.

RSC ADVANCES (2015)

添加到收藏夹

Article Engineering, Mechanical

Study of tribological properties of polyimide/graphene oxide nanocomposite films under seawater-lubricated condition

Chunying Min et al.

TRIBOLOGY INTERNATIONAL (2014)

添加到收藏夹

Article Physics, Multidisciplinary

Dry Sliding Wear Behavior of Al2O3/SiC Particle Reinforced Aluminium Based MMCs Fabricated by Stir Casting Method

N. Altınkok et al.

ACTA PHYSICA POLONICA A (2013)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructure and cavitation-silt erosion behavior of high-velocity oxygen-fuel (HVOF) sprayed Cr3C2-NiCr coating

Sheng Hong et al.

SURFACE & COATINGS TECHNOLOGY (2013)

添加到收藏夹

Article Polymer Science

Pore formation in polystyrene fiber by superimposing temperature and relative humidity of electrospinning atmosphere

H. Fashandi et al.

POLYMER (2012)

添加到收藏夹

Article Engineering, Mechanical

Tribological properties of bronze-graphite composites under sea water condition

Gongjun Cui et al.

TRIBOLOGY INTERNATIONAL (2012)

添加到收藏夹

Article Engineering, Mechanical

Friction and wear behaviors of Al-SiC-B4C composites produced by pressure infiltration method

U. Soy et al.

INDUSTRIAL LUBRICATION AND TRIBOLOGY (2011)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of annealed SUS 304H austenitic stainless steel with copper

Indrani Sen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Galvanic Corrosion Performance of High-Strength Copper-Nickel Alloys in Seawater

R. C. Barik et al.

CORROSION (2009)

添加到收藏夹

Article Materials Science, Coatings & Films

Effect of nano-Al2O3 surface treatment on the tribological performance of phenolic composite coating

Hao-Jie Song et al.

SURFACE & COATINGS TECHNOLOGY (2006)

添加到收藏夹

Article Materials Science, Coatings & Films

Relationships between hardness, Young's modulus and elastic recovery in hard nanocomposite coatings

J Musil et al.

SURFACE & COATINGS TECHNOLOGY (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.