☆ 4.6 Article

Development and Analysis of a Multimaterial FDM 3D Printed Capacitive Accelerometer

IEEE ACCESS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Single-Process 3D-Printed Triaxial Accelerometer

Matic Arh et al.

Summary: This research introduces a three axial piezoresistive accelerometer where the whole sensor, including highly conductive electrical paths, is printed in the same process of thermoplastic material extrusion. The design and manufacturing solutions researched for the triaxial accelerometer can be applied to other 3D-printed sensors, for example, force sensors and opens up the possibility of a single-process 3D-printed smart structure.

ADVANCED MATERIALS TECHNOLOGIES (2022)

添加到收藏夹

Article Agriculture, Dairy & Animal Science

A Case Study Using Accelerometers to Identify Illness in Ewes following Unintentional Exposure to Mold-Contaminated Feed

Sara C. Gurule et al.

Summary: The article investigates the use of accelerometers to monitor sheep behavior before and after illness caused by mold-contaminated feed. Results show a distinct decrease in activity for 4 days after the sheep were exposed to moldy feed, and an increase in activity after treatment of symptomatic sheep. The study suggests that real-time or near real-time accelerometers have the potential to detect illness in sheep.

ANIMALS (2022)

添加到收藏夹

Article Engineering, Electrical & Electronic

Analysis and Development Technique of a Fully 3-D-Printed Differential Capacitive Anemometric Sensor

Alfiero Leoni et al.

Summary: This study presents a novel fully 3D printable wind speed sensor that utilizes embedded electronics and multimaterial fused deposition modeling technology. The feasibility of the sensor is demonstrated through theoretical analysis, simulations, and experimental tests.

IEEE SENSORS JOURNAL (2022)

添加到收藏夹

Article Engineering, Mechanical

Design principles for a single-process 3d-printed accelerometer - theory and experiment

Matic Arh et al.

Summary: Fused-filament fabrication technology has been used for manufacturing various sensors, but faces challenges such as anisotropic behavior and size limitations. This paper focused on the design principles and experimental results of a single-axis accelerometer, providing a foundation for further optimization of the prototype sensor.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2021)

添加到收藏夹

Review Engineering, Electrical & Electronic

3D-printed sensors: Current progress and future challenges

Mohammad Reza Khosravani et al.

SENSORS AND ACTUATORS A-PHYSICAL (2020)

添加到收藏夹

Article Agriculture, Multidisciplinary

Sensor based disease detection: A case study using accelerometers to recognize symptoms of Bovine Ephemeral Fever

Colin Tobin et al.

COMPUTERS AND ELECTRONICS IN AGRICULTURE (2020)

添加到收藏夹

Review Automation & Control Systems

Review of tool condition monitoring in machining and opportunities for deep learning

G. Serin et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

添加到收藏夹

Article Chemistry, Analytical

A Study of Accelerometer and Gyroscope Measurements in Physical Life-Log Activities Detection Systems

Ahmad Jalal et al.

SENSORS (2020)

添加到收藏夹

Article Engineering, Electrical & Electronic

A low noise capacitive MEMS accelerometer with anti-spring structure

Hongcai Zhang et al.

SENSORS AND ACTUATORS A-PHYSICAL (2019)

添加到收藏夹

Article Engineering, Electrical & Electronic

The First 3D-Printed and Wet-Metallized Three-Axis Accelerometer With Differential Capacitive Sensing

Valentina Zega et al.

IEEE SENSORS JOURNAL (2019)

添加到收藏夹

Article Engineering, Civil

Accurate Deformation Monitoring on Bridge Structures Using a Cost-Effective Sensing System Combined with a Camera and Accelerometers: Case Study

Yan Xu et al.

JOURNAL OF BRIDGE ENGINEERING (2019)

添加到收藏夹

Review Telecommunications

Application of MEMS-based accelerometer wireless sensor systems for monitoring of blast-induced ground vibration and structural health: a review

Prashanth Ragam et al.

IET WIRELESS SENSOR SYSTEMS (2019)

添加到收藏夹

Article Engineering, Electrical & Electronic

Autobalancing Analog Front End for Full-Range Differential Capacitive Sensing

Alessandro Depari et al.

IEEE TRANSACTIONS ON INSTRUMENTATION AND MEASUREMENT (2018)

添加到收藏夹

Article Telecommunications

Prototyping and Validation of MEMS Accelerometers for Structural Health MonitoringThe Case Study of the Pietratagliata Cable-Stayed Bridge

Chiara Bedon et al.

JOURNAL OF SENSOR AND ACTUATOR NETWORKS (2018)

添加到收藏夹

Proceedings Paper Engineering, Multidisciplinary

Automatic bridge-based interface for differential capacitive full sensing

G. Ferri et al.

PROCEEDINGS OF THE 30TH ANNIVERSARY EUROSENSORS CONFERENCE - EUROSENSORS 2016 (2016)

添加到收藏夹

Article Physics, Applied

Novel Sensor Structure and Its Evaluation for Integrated Complementary Metal Oxide Semiconductor Microelectromechanical Systems Accelerometer

Toshifumi Konishi et al.

JAPANESE JOURNAL OF APPLIED PHYSICS (2013)

添加到收藏夹

Article Chemistry, Analytical

Analog Wheatstone bridge-based automatic interface for grounded and floating wide-range resistive sensors

Andrea De Marcellis et al.

SENSORS AND ACTUATORS B-CHEMICAL (2013)

添加到收藏夹

Article Engineering, Mechanical

Mechanical fault detection of electric motors by laser vibrometer and accelerometer measurements

C Cristalli et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2006)

添加到收藏夹

Article Engineering, Electrical & Electronic

Three-axes monolithic silicon low-g accelerometer

S Bütefisch et al.

JOURNAL OF MICROELECTROMECHANICAL SYSTEMS (2000)

添加到收藏夹

Article Automation & Control Systems

Micromachined inertial sensors: the state-of-the-art and a look into the future.

M Kraft

MEASUREMENT & CONTROL (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.