☆ 4.5 Article

Insights into the Microstructure and Texture Evolution Using Electron Backscattered Diffraction and Thermal Stability of Low Mn Fe-25Cr-6.5Ni-3.5Mo Alloy

ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Thermal Stability and Residual Stresses in Additively Manufactured Single and Multi-material Systems

Bikash Kumar et al.

Summary: A sequential coupled thermo-mechanical model was developed to monitor the thermal stability, solidification characteristics, and origin of residual stresses in laser-based direct energy deposition of IN718 and IN718-Ti6Al4V systems. The model showed qualitative agreement with experimental measurements. The substitution of IN718 with Ti6Al4V caused a significant temperature rise, low solidification velocity, and large melt pool in the preliminary deposited layers. The overall tensile residual stress reduced due to the lowered thermal gradient, but a reversal of the maximum tensile residual stress location occurred on changing the substrate to Ti6Al4V.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Unidirectional cold rolling of Fe-21Cr-5Mn-1.5Ni alloy - Microstructure, texture and magnetic properties

Tushar Ramdas Dandekar et al.

Summary: In this study, the changes in microstructure, texture, and magnetic properties during the unidirectional cold rolling of a Fe-21Cr-5Mn-1.5Ni alloy were investigated. The results showed that the thickness of the grain along the normal direction reduced more in austenite than in ferrite, and the strain was more partitioned in austenite. The saturation magnetization increased with the increase in cold rolling reduction, and the strain induced martensite (SIM) was similar to 11% after 80% cold rolling. The development of specific textures was observed in both austenite and ferrite after cold rolling, and both texture and strain played a role in the change in magnetic properties.

JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Aging phenomenon in low molybdenum Fe-21Cr-5Mn-1.5Ni alloy: Microstructure evolution, texture development and corrosion behavior

Tushar R. Dandekar et al.

Summary: This study systematically investigated the effect of long-term aging at 750 degrees C on the microstructure evolution, texture development, and corrosion behavior of a low molybdenum Fe-21Cr-1.5Ni-5Mn alloy. The results showed that an increase in aging time resulted in an increase in the proportion of sigma-phase. The sigma-phase formation did not have a specific orientation relationship with neighboring ferrite grains. The lower amount of Cr/Mo and higher N in the alloy delayed the precipitation of the sigma-phase but did not prevent it. The increase in sigma-phase with aging time led to a decrease in corrosion resistance.

MATERIALS TODAY COMMUNICATIONS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Texture, microstructure and mechanical properties of laser beam welded AISI 2507 super duplex stainless steel

Ceyhun Kose et al.

Summary: This study investigates the weldability of AISI 2507 super duplex stainless steel sheets using laser welding. The impact of heat inputs and post-weld heat treatment on the mechanical properties and microstructure of the joints was analyzed. It was found that samples welded with lower heat input exhibited higher microhardness and tensile strength values. Additionally, post-weld heat treatment resulted in decreased hardness and tensile strength but improved toughness and ductility properties.

MATERIALS CHEMISTRY AND PHYSICS (2022)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Insights into the microstructure evolution and crystallographic texture of API X-65 steel/UNS S32750 stainless steel dissimilar welds by EBSD analysis

Morteza Shamanian et al.

Summary: In this study, the microstructural features and microtexture evolution of API X-65 steel welded to UNS S32750 stainless steel were evaluated with different heat input (HI) values. It was found that decreasing the HI value led to a decrease in the fractions of austenite, resulting in almost equal fractions of austenite and ferrite phases in the weldment using the HI value of 0.68 kJ/mm. The impact resistance of the weld metals was slightly better compared to the base metals.

WELDING IN THE WORLD (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Strain rate sensitivity behaviour of Fe-21Cr-1.5Ni-5Mn alloy and its constitutive modelling

Tushar Ramdas Dandekar et al.

Summary: The hot deformation behavior of Fe-21Cr-1.5Ni-5Mn alloy was studied through isothermal unidirectional hot compression tests, showing that the developed model accurately portrayed its flow behavior. The hot deformation activation energy for peak stress was found to be 508.3 kJ mol(-1), with the best match between experimental and predicted flow stress obtained at 975 degrees C.

MATERIALS CHEMISTRY AND PHYSICS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Multistep Cross Rolling of UNS S32101 Steel: Microstructure, Texture, and Magnetic Properties

Tushar R. Dandekar et al.

Summary: The effect of multistep cross rolling on UNS S32101 steel microstructure, texture, and magnetic properties was investigated in this study. It was found that cold-rolling reduction led to changes in microstructure and magnetic properties, as well as the formation of strain-induced martensite. Analysis of hysteresis loops and microstructures allowed for a better understanding of the impact of cold-rolling reduction on the properties of UNS S32101 steel.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural influence of sigma phase on pitting corrosion behavior of duplex stainless steel/NaCl electrolyte couple

David D. S. Silva et al.

Summary: This study investigates the effects of the sigma phase on pitting corrosion behavior of thermally-aged duplex stainless steel, using structural, morphological, and electrochemical characterizations. Potentiodynamic tests in 1M NaCl solution at different temperatures were conducted, along with 3D roughness image comparisons for before and after corrosion tests. The study concludes that potentiodynamic tests combined with optical profilometry are a successful approach to evaluate surface degradation mechanisms due to pitting corrosion.

MATERIALS CHEMISTRY AND PHYSICS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Phase transformations of the duplex stainless steel UNS S31803 under non-isothermal conditions

Gabrielle Cristine Lemos Duarte Freitas et al.

Summary: The precipitation of intermetallic phases causes embrittlement in duplex stainless steels. Cooling cycles on UNS S31803 specimens showed that the volume fraction of σ and χ formed was lower than expected, possibly due to the initial DSS morphology.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of isothermal aging at 750 °C on microstructure and mechanical properties of UNS S32101 lean duplex stainless steel

Tushar Ramdas Dandekar et al.

Summary: The study reveals that aging treatment of UNS S32101 at 750 degrees Celsius leads to significant changes in the microstructure and mechanical properties of lean duplex stainless steel, including precipitate formation, decrease in impact energy, transition in fracture morphology, and alterations in tensile properties.

MATERIALS TODAY COMMUNICATIONS (2021)

添加到收藏夹

Article Engineering, Manufacturing

On the interaction of microstructural morphology with residual stress in fiber laser welding of austenitic stainless steel

Bikash Kumar et al.

Summary: The study investigates the relationship between microstructure and residual stress in Yb-fiber laser-welded austenitic stainless steel, considering the influence of solid-state phase transformation on residual stress distribution. Low heat input results in high cooling rate, excellent tensile strength, and low tensile residual stress.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)

添加到收藏夹

Review Engineering, Multidisciplinary

Dissimilar welding of duplex stainless steel with Ni alloys: A review

Anup Kumar Maurya et al.

Summary: This review article provides an overview of the microstructure and mechanical behavior of dissimilar welded joints, with a focus on the challenges related to the dissimilar welding of super DSS 2507 with nitronic steel (N50) and Inconel 625.

INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2021)

添加到收藏夹

Article Thermodynamics

Development of avocado shape heat source model for finite element based heat transfer analysis of high-velocity arc welding process

A. K. Mondal et al.

Summary: The accuracy of the welding heat source model affects the prediction accuracy of the thermal profile of the welded joint. The geometric shape of the moving heat source in fusion welding is determined by the welding speed, with the avocado shape heat source model proposed as a more realistic and flexible approximation model.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2021)

添加到收藏夹

Article Engineering, Multidisciplinary

Characterization of structure-property relationship of martensitic P91 and high alloy ferritic austenitic F69 steel

S. Sirohi et al.

INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Cooling Rate on the Precipitation Behavior of a Fe-Cr-Ni Alloy

Amit Kumar et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

添加到收藏夹

Article Engineering, Industrial

Multi-pass arc welding techniques of 12 mm thick super-duplex stainless steel

D. Arun et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

添加到收藏夹

Article Optics

Phase transformation effect in distortion and residual stress of thin-sheet laser welded Ti-alloy

Bikash Kumar et al.

OPTICS AND LASERS IN ENGINEERING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Shielded metal arc welding of UNS S32750 steel: microstructure, mechanical properties and corrosion behaviour

Tushar Ramdas Dandekar et al.

MATERIALS RESEARCH EXPRESS (2018)

添加到收藏夹

Article Engineering, Manufacturing

Laser powder bed fusion of nickel alloy 625: Experimental investigations of effects of process parameters on melt pool size and shape with spatter analysis

Luis E. Criales et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2017)

添加到收藏夹

Review Multidisciplinary Sciences

Weldability, machinability and surfacing of commercial duplex stainless steel AISI2205 for marine applications - A recent review

A. Vinoth Jebaraj et al.

JOURNAL OF ADVANCED RESEARCH (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure characterization of a duplex stainless steel weld by electron backscattering diffraction and orientation imaging microscopy techniques

Isabela Viegas Aguiar et al.

MATERIA-RIO DE JANEIRO (2015)

添加到收藏夹

Article Thermodynamics

Development of egg-configuration heat source model in numerical simulation of autogenous fusion welding process

N. Yadaiah et al.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of cooling rate on microstructure evolution and pitting corrosion resistance in the simulated heat-affected zone of 2304 duplex stainless steels

Lindou Chen et al.

CORROSION SCIENCE (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Texture, microstructure and anisotropic properties in annealed 2205 duplex stainless steel welds

R. Badji et al.

MATERIALS CHARACTERIZATION (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Measuring Secondary Phases in Duplex Stainless Steels

I. Calliari et al.

JOM (2009)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Characterization of the microstructure, crystallographic texture and segregation of an as-cast duplex stainless steel slab

Clara Herrera et al.

STEEL RESEARCH INTERNATIONAL (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Characterization of microstructure, chemical composition, corrosion resistance and toughness of a multipass weld joint of superduplex stainless steel UNS S32750

S. S. M. Tavares et al.

MATERIALS CHARACTERIZATION (2007)

添加到收藏夹

Article Nanoscience & Nanotechnology

Stored energy evolution in both phases of a duplex steel as a function of cold rolling reduction

AL Etter et al.

SCRIPTA MATERIALIA (2006)

添加到收藏夹

Article Engineering, Industrial

Structure and properties of the heat-affected zone of duplex steels welded joints

J Nowacki et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)

添加到收藏夹

Article Materials Science, Multidisciplinary

Evolution of microstructure and texture in Mg-Al-Zn alloys during electron-beam and gas tungsten arc welding

SH Wu et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2004)

添加到收藏夹

Article Materials Science, Multidisciplinary

A quantitative analysis of the evolution of texture and stored energy during annealing of cold rolled copper

P Gerber et al.

ACTA MATERIALIA (2003)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of weld metal chemistry and heat input on the structure and properties of duplex stainless steel welds

V Muthupandi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

添加到收藏夹

Article Physics, Applied

Heat transfer and fluid flow during laser spot welding of 304 stainless steel

X He et al.

JOURNAL OF PHYSICS D-APPLIED PHYSICS (2003)

添加到收藏夹

Article Engineering, Multidisciplinary

Finite volume methods applied to the computational modelling of welding phenomena

GA Taylor et al.

APPLIED MATHEMATICAL MODELLING (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.