相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Dimensional assessment of uniformly periodic porosity primitive TPMS lattices using additive manufacturing laser powder bed fusion technique
Ali Mulhi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2023)
Microstructures and mechanical properties of NiTi shape memory alloys fabricated by wire arc additive manufacturing
Lin Yu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2022)
Effect of Interpass Temperature on Wire Arc Additive Manufacturing Using High-Strength Metal-Cored Wire
Wengang Zhai et al.
METALS (2022)
Structure, martensitic transformations and mechanical behaviour of NiTi shape memory alloy produced by wire arc additive manufacturing
N. Resnina et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2021)
Selective laser melting of Cu-Ni-Sn: A comprehensive study on the microstructure, mechanical properties, and deformation behavior
Chao Zhao et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2021)
Laser powder bed fusion of a superelastic Cu-Al-Mn shape memory alloy
N. Babacan et al.
MATERIALS & DESIGN (2021)
Multi-scale pseudoelasticity of NiTi alloys fabricated by laser additive manufacturing
Dongzhe Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)
Effect of Interlayer Delay on the Microstructure and Mechanical Properties of Wire Arc Additive Manufactured Wall Structures
Shalini Singh et al.
MATERIALS (2021)
Investigations on NiTi shape memory alloy thin wall structures through laser marking assisted wire arc based additive manufacturing
Shalini Singh et al.
JOURNAL OF MANUFACTURING PROCESSES (2021)
Studies on development of NiTi-integrated optical fiber sensor and its life cycle behavior
Shalini Singh et al.
JOURNAL OF INTELLIGENT MATERIAL SYSTEMS AND STRUCTURES (2020)
The effect of processing parameters on rapid-heating β recrystallization in inter-pass deformed Ti-6Al-4V wire-arc additive manufacturing
A. E. Davis et al.
MATERIALS CHARACTERIZATION (2020)
Optimization of Cold Metal Transfer-Based Wire Arc Additive Manufacturing Processes Using Gaussian Process Regression
Seung Hwan Lee
METALS (2020)
Comparative study of eutectic Al-Si alloys manufactured by WAAM and casting
Geir Langelandsvik et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Cu-Ni-Sn alloy fabricated by melt spinning and selective laser melting: a comparative study on the microstructure and formation kinetics
Chao Zhao et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Shape memory effect, temperature distribution and mechanical properties of friction stir welded nitinol
S. S. Mani Prabu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Location dependence of microstructure, phase transformation temperature and mechanical properties on Ni-rich NiTi alloy fabricated by wire arc additive manufacturing
Jun Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Effect of Heat Treatment on Repetitively Scanned SLM NiTi Shape Memory Alloy
Zhong Xun Khoo et al.
MATERIALS (2019)
Comparative investigation of microstructure, mechanical properties and strengthening mechanisms of Al-12Si/TiB2 fabricated by selective laser melting and hot pressing
L. X. Xi et al.
CERAMICS INTERNATIONAL (2018)
Grain morphology evolution and texture characterization of wire and arc additive manufactured Ti-6Al-4V
Jian Wang et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement
Bintao Wu et al.
JOURNAL OF MANUFACTURING PROCESSES (2018)
Effects of aging and cooling rate on the transformation of nanostructured Ti-50.8Ni
Raghavendra R. Adharapurapu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Design for Wire plus Arc Additive Manufacture: design rules and build orientation selection
Helen Lockett et al.
JOURNAL OF ENGINEERING DESIGN (2017)
Effects of heat accumulation on the arc characteristics and metal transfer behavior in Wire Arc Additive Manufacturing of Ti6Al4V
Bintao Wu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Microstructural Analyses of ATI 718PlusA® Produced by Wire-ARC Additive Manufacturing Process
G. Asala et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)
Three-dimensional numerical simulation of arc and metal transport in arc welding based additive manufacturing
Xiangman Zhou et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2016)
Influence of milling time on microstructure and magnetic properties of Fe80P11C9 alloy produced by mechanical alloying
A. H. Taghvaei et al.
JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS (2015)
Effect of inter-layer dwell time on distortion and residual stress in additive manufacturing of titanium and nickel alloys
Erik R. Denlinger et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Investigations on the influence of composition in the development of Ni-Ti shape memory alloy using laser based additive manufacturing
S. Shiva et al.
OPTICS AND LASER TECHNOLOGY (2015)
Influence of Ni4Ti3 precipitates on phase transformation of NiTi shape memory alloy
Shu-yong Jiang et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2015)
Production of Porous β-Type Ti-40Nb Alloy for Biomedical Applications: Comparison of Selective Laser Melting and Hot Pressing
Ksenia Zhuravleva et al.
MATERIALS (2013)
Synthesis and Characterization of NanocrystallineMg-7.4%Al Powders Produced by Mechanical Alloying
Anil Kumar Chaubey et al.
METALS (2013)
A 3D dynamic analysis of thermal behavior during single-pass multi-layer weld-based rapid prototyping
Huihui Zhao et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)