☆ 3.9 Article

Investigation of delamination and surface roughness in end milling of glass fibre reinforced polymer composites using Fuzzy Model and Grey wolf Optimizer

INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Chemical

A parametric study on the mechanical properties of MIG and TIG welded dissimilar steel joints

Mehmet Sukru Adin

Summary: The effects of Total Accumulated Weld Volumes (TAWV) and different groove angles on the mechanical properties of AISI 1040 and AISI 8620 cylindrical steel joints were investigated. The results showed that the TIG welded joint had the highest average Ultimate Tensile Strength (UTS) of 579.611 MPa, while the MIG welded joint had the lowest average UTS value of 424.611 MPa. The UTS values of the joints were positively affected by the increase in TAWV, and the 90 degrees groove angled joint had a 40.25% higher UTS value than the 45 degrees groove angled joint.

JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY (2023)

添加到收藏夹

Article Polymer Science

Acquisition of Key Vacuum-Assisted Resin Transfer Molding Parameters through Reverse Scanning for Application in the Manufacturing of Large Fiber-Reinforced-Plastic Products

Guang-Min Luo et al.

Summary: In this study, a method for rapid porosity and permeability estimation was developed using GeoDict software and reverse scanning. The proposed method showed a 10% variation in porosity and permeability parameters compared to one-dimensional resin flow and Easyperm tests. The integration of the proposed method with Moldex3D allowed for accurate simulation of resin flow in large FRP products with a variation of less than 8%. This method can increase process planning efficiency and product stability in large wind turbine FRP parts and FRP yacht components.

INTERNATIONAL JOURNAL OF POLYMER SCIENCE (2023)

添加到收藏夹

Article Engineering, Manufacturing

Abrasive water jet machining of glass fibre reinforced polymer composite: experimental investigation, modelling and optimization

Anil Kumar Dahiya et al.

Summary: This paper presents an experimental investigation, modelling, and optimization of abrasive water jet machining (AWJM) of glass fibre reinforced polymer composite. The effects of water pressure, stand-off distance, traverse rate, and abrasive mass flow rate on delamination length, surface roughness, and kerf taper are studied. Regression models are developed to predict these parameters using response surface methodology. A desirability function approach is used for multi-objective optimization, achieving a reasonably good and acceptable combination of desired values. The confirmation test shows that the optimized process parameters result in low percentage errors for all three parameters.

INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM (2023)

添加到收藏夹

Article Engineering, Manufacturing

Effect of MWCNTS on mechanical properties of woven fabric hybrid polymeric nanocomposites and finite element analysis of nanocomposite

Suhas Uthale et al.

Summary: This study investigated the mechanical behavior of hybrid polymeric nanocomposites with 0.1 wt% and 0.2 wt% multi-walled carbon nanotubes (MWCNTs), and studied the effect of fiber orientation on the mechanical properties of the hybrid nanocomposites. It was found that adding MWCNTs to the epoxy enhanced the mechanical properties. Hybrid composite and hybrid nanocomposite panels were made using vacuum assisted resin transfer molding (VARTM). Test specimens were cut from the composites and tested according to ASTM standards. The results showed that the hybrid nanocomposite with 0.1 wt% of MWCNTs exhibited improved strength and properties at a relatively low cost.

INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM (2023)

添加到收藏夹

Article Engineering, Mechanical

Sliding-friction wear of a seashell particulate reinforced polymer matrix composite: modeling and optimization through RSM and Grey Wolf optimizer

P. Vasanthkumar et al.

Summary: This study investigated the friction wear of a thermoplastic polymer reinforced with seashell particles. Experimental design and multiobjective analysis revealed that the interface temperature was highly influenced by rotational speed, and the coefficient of friction was significantly affected by rotational speed and the proportion of seashell particles.

TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING (2022)

添加到收藏夹

Article Materials Science, Characterization & Testing

Effect of particles on tensile and bending properties of jute epoxy composites

Hamit Adin et al.

Summary: The mechanical properties of composite materials made from woven jute were investigated by adding aluminum, mica, and ceramic particles into epoxy adhesive layers. Results showed that the tensile and bending failure loads of the composite materials increased with the use of particle-reinforced adhesive. The biggest improvements were seen with 4 wt% aluminum for tensile strength and 2 wt% aluminum for bending strength.

MATERIALS TESTING (2022)

添加到收藏夹

Article Engineering, Mechanical

Experimental and simulation approach of surface generation on K-80 alumina ceramic by recently developed sustainable FB-HAJM using novel nozzle design

Subhadip Pradhan et al.

Summary: This study aims to analyze the kerf angle, surface roughness, and material removal rate in the HAJMing process of K-80 alumina ceramic, and proposes two multi-objective optimization methods to improve cutting efficiency and performance. The results show the feasibility and importance of using hot abrasives in the FB-HAJM method for industrial applications in aerospace, precision manufacturing, and the biomedical field.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART E-JOURNAL OF PROCESS MECHANICAL ENGINEERING (2022)

添加到收藏夹

Article Polymer Science

Optimization of Typha Fibre Extraction and Properties for Bio-Composite Applications Using Desirability Function Analysis

Mahmudul Hasan et al.

Summary: The study investigated the optimal extraction parameters for cattail fibers and used a desirability function analysis for optimization, confirming the validity of the optimum treatment conditions.

POLYMERS (2022)

添加到收藏夹

Article Engineering, Mechanical

VARTM process of composites using double-bag air cushion method

Chih-Yuan Chang et al.

Summary: This article introduces the double-bag air cushion method as an economical and efficient manufacturing process for polymer composites. Experimental evaluation shows that this method can significantly reduce infusion time and has good mechanical properties.

TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Numerical Modelling, Simulation, and Analysis of the End-Milling Process Using DEFORM-3D with Experimental Validation

B. Deepanraj et al.

Summary: In this study, a FEA-based simulation of end-milling of AISI1045 steel using a tungsten carbide tool was performed. The simulation considered tool wear model, material model, and adaptive remeshing. The impact of machining variables on temperature, stress, cutting forces, etc. was investigated, and the optimal combination of variables was determined. The simulation results showed good correlation with experimental results.

ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Study of the Machining Process of GFRP Materials by Milling Technology with Coated Tools

Artur Knap et al.

Summary: This study focused on the milling of fabric-bonded GFRP plates and investigated the influence of glass fiber abrasion on tool wear and life, as well as the surface roughness, delamination, and forces during machining. The findings provide valuable insights for researchers in understanding specific aspects of milling GFRP composites.

COATINGS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Drilling Parameters Analysis on In-Situ Al/B4C/Mica Hybrid Composite and an Integrated Optimization Approach Using Fuzzy Model and Non-Dominated Sorting Genetic Algorithm

Palanikumar Kayaroganam et al.

Summary: In-situ hybrid metal matrix composites were prepared by reinforcing AA6061 aluminum alloy with B4C and mica. The machinability of the hybrid composite was evaluated through drilling tests with different input parameters. Results showed that mica reinforcement was crucial in reducing thrust force and torque during drilling, and optimal drill parameters were determined to minimize energy consumption and production costs.

METALS (2021)

添加到收藏夹

Article Energy & Fuels

Optimization of tensile strength of PLA/clay/rice husk composites using Box-Behnken design

Vianney Andrew Yiga et al.

Summary: The study optimized the tensile strength of PLA/clay/rice husk composites using response surface methodology, and validated the accuracy of the models through experiments.

BIOMASS CONVERSION AND BIOREFINERY (2021)

添加到收藏夹

Review Polymer Science

Review and Suggestion of Failure Theories in Voids Scenario for VARTM Processed Composite Materials

Vivek Kumar Dhimole et al.

Summary: Fiber-reinforced composite structures are widely used in various applications due to their excellent strength to weight ratio. Vacuum-assisted resin transfer molding (VARTM) is a highly productive and cost-effective manufacturing process, but the presence of voids and fiber misalignment in the final processed composite can impact its strength and reliability. Proper selection and understanding of failure theories are necessary to account for void defects and improve the design effectiveness for composites.

POLYMERS (2021)

添加到收藏夹

Article Energy & Fuels

Application of a simplified Grey Wolf optimization technique for adaptive fuzzy PID controller design for frequency regulation of a distributed power generation system

Sasmita Padhy et al.

Summary: The study introduces a Simplified Grey Wolf Optimizer (SGWO) for optimization tasks, demonstrating its superior performance over the original Grey Wolf Optimizer (GWO) in terms of solution quality and execution time. By designing an Adaptive Fuzzy PID controller using SGWO in a Distributed Power Generation System, the study shows the effectiveness of SGWO in optimal controller design tasks.

PROTECTION AND CONTROL OF MODERN POWER SYSTEMS (2021)

添加到收藏夹

Article Engineering, Electrical & Electronic

The Grey Wolf Optimizer and Its Applications in Electromagnetics

Xun Li et al.

IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION (2020)

添加到收藏夹

Article Engineering, Mechanical

A fuzzy logic approach for modelling and prediction of mechanical properties of hybrid abaca-reinforced polymer composite

Agnivesh Kumar Sinha et al.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2020)

添加到收藏夹

Article Multidisciplinary Sciences

An Improved Grey Wolf Optimizer Based on Differential Evolution and Elimination Mechanism

Jie-Sheng Wang et al.

SCIENTIFIC REPORTS (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Parametric analysis of delamination in GFRP composite profiles by performing rotary ultrasonic drilling approach: Experimental and statistical study

Mohammad Baraheni et al.

COMPOSITES PART B-ENGINEERING (2019)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Optimization of surface roughness and delamination factor in end milling of graphene modified GFRP using response surface methodology

R. K. Thakur et al.

MATERIALS TODAY-PROCEEDINGS (2019)

添加到收藏夹

Article Automation & Control Systems

Investigations on performance characteristics of GFRP composites in milling

I. S. N. V. R. Prasanth et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Critical Analysis in Milling of GFRP Composites by Various End Mill Tools

I. S. N. V. R. Prashanth et al.

MATERIALS TODAY-PROCEEDINGS (2018)

添加到收藏夹

Article Computer Science, Artificial Intelligence

Multi-objective grey wolf optimizer: A novel algorithm for multi-criterion optimization

Seyedali Mirjalili et al.

EXPERT SYSTEMS WITH APPLICATIONS (2016)

添加到收藏夹

Article Engineering, Multidisciplinary

An experimental investigation on the process parameters influencing machining forces during milling of carbon and glass fiber laminates

N. Rajesh Mathivanan et al.

MEASUREMENT (2016)

添加到收藏夹

Article Engineering, Mechanical

Modelling of machining force in end milling of GFRP composites using MRA and ANN

M. P. Jenarthanan et al.

AUSTRALIAN JOURNAL OF MECHANICAL ENGINEERING (2016)

添加到收藏夹

Article Computer Science, Interdisciplinary Applications

Grey Wolf Optimizer

Seyedali Mirjalili et al.

ADVANCES IN ENGINEERING SOFTWARE (2014)

添加到收藏夹

Proceedings Paper Engineering, Mechanical

A study on Edge Milling Operation of NEMA G11 GFRP Composites based on Grey-Taguchi method

Hari Vasudevan et al.

DYNAMICS OF MACHINES AND MECHANISMS, INDUSTRIAL RESEARCH (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Analysis of delamination in drilling glass fiber reinforced polyester composites

T. V. Rajamurugan et al.

MATERIALS & DESIGN (2013)

添加到收藏夹

Article Engineering, Multidisciplinary

A comparative study on the use of drilling and milling processes in hole making of GFRP composite

Hussein M. Ali et al.

SADHANA-ACADEMY PROCEEDINGS IN ENGINEERING SCIENCES (2013)

添加到收藏夹

Article Engineering, Manufacturing

Experimental Study of Machinability of GFRP Composites by End Milling

A. I. Azmi et al.

MATERIALS AND MANUFACTURING PROCESSES (2012)

添加到收藏夹

Article Engineering, Manufacturing

Application of fuzzy logic for modeling surface roughness in turning CFRP composites using CBN tool

T. Rajasekaran et al.

PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2011)

添加到收藏夹

Article Materials Science, Composites

Delamination Analysis in Drilling of CFRP Composites Using Response Surface Methodology

A. Krishnamoorthy et al.

JOURNAL OF COMPOSITE MATERIALS (2009)

添加到收藏夹

Article Engineering, Manufacturing

Analysis of Thrust Force in Drilling Glass Fiber-Reinforced Plastic Composites Using Fuzzy Logic

B. Latha et al.

MATERIALS AND MANUFACTURING PROCESSES (2009)

添加到收藏夹

Article Engineering, Manufacturing

Evaluation of Delamination in Drilling GFRP Composites

K. Palanikumar et al.

MATERIALS AND MANUFACTURING PROCESSES (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Optimization of machining parameters in turning GFRP composites using a carbide (K10) tool based on the Taguchi method with fuzzy logics

K. Palanikumar et al.

METALS AND MATERIALS INTERNATIONAL (2006)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.