☆ 4.6 Article

Prediction and experimental verification of phase transformation plasticity

MATERIALS TODAY COMMUNICATIONS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Cu-assisted austenite reversion and enhanced TRIP effect in maraging stainless steels

M. C. Niu et al.

Summary: Control of the formation and stability of reverted austenite is critical in achieving a favorable combination of strength, ductility, and toughness in high-strength steels. The effects of Cu precipitation on the austenite reversion and mechanical properties of maraging stainless steels were investigated. Cu accelerates the austenite reversion kinetics by increasing the equilibrium austenite fraction and serving as heterogeneous nucleation sites. Cu precipitation hardening compensates the strength drop induced by the formation of soft reverted austenite.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Bainitic Isothermal Treatment on the Microstructure and Mechanical Properties of a CMnSiAl TRIP Steel

Alexis Guzman et al.

Summary: The effect of partial substitution of Si by Al in TRIP-assisted CMnSiAl steels was investigated. The steel was processed through various heat treatments to obtain different microstructures. The TRIP effect resulted in a transformation of retained austenite during tensile tests, leading to improved elongation. Furthermore, the partial substitution of Si by Al decreased the yield strength and increased the total elongation of the steel.

METALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparative Evaluation of the TRIP Effect in Steels with Different Contents of Mn and Al

Mircea Cristian Pantilimon et al.

Summary: This paper presents a comparison between four TRIP steels belonging to two different groups. Through heat treatment and impact bending test, it was found that two steels from different groups showed similar mechanical shock behaviors and similar proportions of retained austenite transformed into martensite. Additionally, the steel with the highest Mn percentage exhibited the highest hardness and proportions of retained austenite and martensite.

METALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

The relationship between austenite morphology and continuous TRIP effects in forged 4Mn steel

Ran Tao et al.

Summary: In this study, forged medium-Mn steel with high tensile strength and elongation was developed, and the effect of quenching temperature on its properties was investigated. Different morphologies of austenite showed different stability during the deformation process. This finding provides theoretical guidance for controlling the microstructure of high-performance medium-Mn steels.

MATERIALS CHARACTERIZATION (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

A new understanding of transformation induced plasticity (TRIP) effect in austenitic steels

Liyang Zeng et al.

Summary: This study investigates the TRIP effect in austenitic steels by simulating experiments and using microstructural characterization methods. The results show that different types of martensitic transformations are associated with changes in SHR at different stages of deformation, and the contribution of DAMAI effect on SHR is greater than that of SIMT effect.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Kinetics of strain-induced phase transformation in TRIP steel

V. Danilov et al.

Summary: This study discusses the kinetics of fronts of localized plastic deformation in TRIP steel using a combination of DIC methods and magnetization measurements. It is found that the kinetics of deformation fronts are mainly determined by the stages of the hardening curve, consistent with changes in the phase composition. The phase transformation starts with the propagation of Luders bands and then proceeds through the formation and propagation of Portevin-Le Chatelier bands, only in the region of increasing strain hardening coefficient.

MATERIALS LETTERS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Transformation plasticity of AF1410 steel and its influences on the welding residual stress and distortion: Experimental and numerical study

Kaiyuan Zhang et al.

Summary: This study investigated the influence of transformation plasticity on welding residual stress and distortion in AF1410 steel through experimental and numerical simulation methods. The results showed that transformation plasticity can reduce stress variation, but has little impact on distortion.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of matrix structures on TRIP effect and mechanical properties of low-C low-Si Al-added hot-rolled TRIP steels

Xiaodong Tan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Abnormal TRIP effect on the work hardening behavior of a quenching and partitioning steel at high strain rate

M. Wang et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Cooling Rate on Transformation Plasticity of 0.45% Carbon Steel

Takayuki Otsuka et al.

ISIJ INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Experiment research on the transformation plasticity by tensile/compressive stress and transformation kinetics during the martensitic transformation of 30Cr2Ni4MoV steel

Jie Liu et al.

MATERIALS RESEARCH EXPRESS (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effects of Plastic Stress on Transformation Plasticity and Microstructure of a Carbide-Free Bainite Steel

Mengen Liu et al.

METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of Transformation Plasticity on the Distribution of Internal Stress in Three Water-Quenched Cylinders

Yu Liu et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2017)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effects of Applied Stress on Isothermal Phase Transformation of Austenite to Pearlite in Heavy Rail Steels: An Experimental and Modeling Study

Lin Chen et al.

METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2016)

添加到收藏夹

Article Multidisciplinary Sciences

Analysis of Transformation Plasticity in Steel Using a Finite Element Method Coupled with a Phase Field Model

Yi-Gil Cho et al.

PLOS ONE (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Diffusion-controlled transformation plasticity of steel under externally applied stress

H. N. Han et al.

PHILOSOPHICAL MAGAZINE (2007)

添加到收藏夹

Article Engineering, Mechanical

New investigations on transformation induced plasticity and its interaction with classical plasticity

L Taleb et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Transformation plasticity at different phase transformations of a bearing steel

M Dalgic et al.

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

A model for transformation plasticity during bainite transformation of steel under external stress

HN Han et al.

ACTA MATERIALIA (2003)

添加到收藏夹

Article Engineering, Mechanical

Experimental study of the phase transformation plasticity of 16MND5 low carbon steel under multiaxial loading

M Coret et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2002)

添加到收藏夹

Article Materials Science, Multidisciplinary

Models for transformation plasticity in loaded steels subjected to bainitic and martensitic transformation

CC Liu et al.

MATERIALS SCIENCE AND TECHNOLOGY (2001)

添加到收藏夹

Article Engineering, Mechanical

Experimental analysis of transformation plasticity

L Taleb et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2001)

添加到收藏夹

Article Engineering, Mechanical

A new view on transformation induced plasticity (TRIP)

FD Fischer et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.