☆ 4.7 Article

Optimization of the accumulative roll bonding process parameters and SiC content for optimum enhancement in mechanical properties of Al-Ni-SiC composites

ALEXANDRIA ENGINEERING JOURNAL (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Fatigue-induced microstructure evolution and ratcheting behavior of ultrafine-grained (UFG) pure aluminum processed by accumulative roll bonding (ARB)

S. Karami et al.

Summary: In this study, the fatigue and cyclic deformation behavior of ultrafine-grained pure aluminum AA1100 product by accumulative roll bonding (ARB) process under stress-controlled in the presence of mean stress were investigated. The tensile properties of the material were improved due to grain refinement caused by severe strain imposed during seven cycles of the ARB process. The fatigue life was found to depend greatly on the ARB cycle, showing an increase with the increasing cycle. TEM observations revealed the microstructural evolution induced by fatigue, with dense dislocation patterns recovering and transforming during cyclic deformation.

MATERIALS CHARACTERIZATION (2023)

添加到收藏夹

Article Engineering, Chemical

Utilizing a unified conceptual dynamic model for prediction of particle size of duel-matrix nanocomposites during mechanical alloying

H. Ahmadian et al.

Summary: This study developed an analytical model to predict the morphological changes in nanocomposite powders during mechanical alloying. The model was applied to predict the particle size of magnesium-based hybrid composite powder reinforced with Ti and SiC. The effect of milling time on the morphology, microstructure, and particle size of composite powders was explored. Experimental and model predictions showed different optimal milling times for different materials, and increasing milling time led to changes in crystalline structure and crystallite size.

POWDER TECHNOLOGY (2023)

添加到收藏夹

Article Engineering, Multidisciplinary

An enhanced Dendritic Neural Algorithm to predict the wear behavior of alumina coated silver reinforced copper nanocomposites

A. M. Sadoun et al.

Summary: Due to the lack of analytical solutions, a modified machine learning method named Dendritic Neural (DN) was used to predict the wear performance of copper-alumina (Cu-Al2O3) nanocomposites. The optimal weights of DN were determined by a new meta-heuristic technique named Artificial Hummingbird Algorithm (AHA) to improve its performance. The developed model using AHA algorithm showed excellent predictability of the wear rate and coefficient of friction for Cu-Al2O3 nanocomposites with reinforcement content up to 10%.

ALEXANDRIA ENGINEERING JOURNAL (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Prediction of the tensile properties of ultrafine grained Al-SiC nanocomposites using machine learning

I. M. R. Najjar et al.

Summary: We used machine learning (ML) to analyze the tensile strength of aluminum nanocomposites reinforced with m-SiC particles fabricated by ARB. The effect of ARB passes on the microstructure, phase analysis, tensile, and hardness properties was investigated. The experimental results showed the improved distribution of SiC particles with increasing ARB passes. The developed ML model, based on the Growth Optimizer Algorithm, accurately predicts the tensile properties of the composites.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the prediction of the mechanical properties of ultrafine grain Al-TiO2 nanocomposites using a modified long-short term memory model with beluga whale optimizer

Ghazi S. Alsoruji et al.

Summary: This study presents a machine learning model based on long-short term memory model and beluga whale optimizer to predict the mechanical properties of ultrafine grain Al-TiO2 nanocomposites. The model shows excellent accuracy in predicting the yield and ultimate strengths, elongation, and hardness of the composites tested.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Strength evolution during accumulative roll bonding of the metal matrix composite

H. Parvin et al.

Summary: The strength evolution of metal matrix composite during processing/cycling via accumulative roll bonding (ARB) is analyzed using a twofold model. The evolution consists of monolithic-like behavior and composite-like behavior, with each behavior making a different contribution. Particle effectiveness is lowest at the beginning of the cycling process and reaches its highest value during the later cycles. The onset of declining monolithic-like behavior is observed at a critical strain, and there is a minimum strain at which composite-like behavior dominates.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Engineering, Mechanical

Feasibility study of producing Al-5Zn-1 Mg alloy by accumulative roll bonding process and subsequent heat treatment

Morteza Alizadeh et al.

Summary: In this research, Al/5Zn/1Mg composite sheets were produced by the ARB process and transformed into Al-5Zn-1Mg alloy sheets through a heat treatment process. Structural investigations using SEM, EDS, and XRD showed the distribution of Zn layers and Mg powder particles in the Al matrix, as well as the formation of the alpha phase. Tensile and microhardness measurements demonstrated the improvement in mechanical properties with increasing ARB cycles.

ENGINEERING FAILURE ANALYSIS (2023)

添加到收藏夹

Article Engineering, Civil

Fracture toughness, wear, and microstructure properties of aluminum/titanium/steel multi-laminated composites produced by cross-accumulative roll-bonding process

Yaping Wang et al.

Summary: This paper investigates the microstructure and mechanical properties of aluminum/titanium/steel multi-laminated composites fabricated by the CARB process. Increasing the number of rolling passes resulted in more instabilities, decreased ultimate and yield strength, decreased elongation, and changes in fracture toughness and wear mechanisms.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2022)

添加到收藏夹

Article Chemistry, Physical

BONDING PROPERTIES OF Al/Al2O3 BULK COMPOSITES PRODUCED VIA COMBINED STIR CASTING AND ACCUMULATIVE PRESS BONDING

Saade Abdalkareem Jasim et al.

Summary: In this study, Al/Al2O3 composites were fabricated by combining stir casting and accumulative press bonding (APB) processes. The effect of the APB method on the bonding properties of the samples was investigated. It was found that increasing the pressing temperature and decreasing the Al2O3 particle content improved the bonding quality. Increasing the number of APB steps enhanced the bonding strength up to a certain point and then decreased the average peeling force.

SURFACE REVIEW AND LETTERS (2022)

添加到收藏夹

Article Mathematics

Utilization of Improved Machine Learning Method Based on Artificial Hummingbird Algorithm to Predict the Tribological Behavior of Cu-Al2O3 Nanocomposites Synthesized by In Situ Method

Ayman M. Sadoun et al.

Summary: This paper presents a machine learning model using the artificial hummingbird algorithm to predict the effect of Al2O3 nanoparticles content on the wear rates in Cu-Al2O3 nanocomposite. The experimental results show that the addition of Al2O3 nanoparticles can improve the microhardness of the composite and reduce its wear rate. The developed model is able to accurately predict the wear rates under different wear conditions.

MATHEMATICS (2022)

添加到收藏夹

Article Engineering, Mechanical

Prediction of Tribological Properties of Alumina-Coated, Silver-Reinforced Copper Nanocomposites Using Long Short-Term Model Combined with Golden Jackal Optimization

Ismail R. Najjar et al.

Summary: This study presented a newly modified machine learning model to predict the tribological performance of Cu-Al2O3 nanocomposites, which were developed using electroless coating of Al2O3 nanoparticles with Ag, ball milling, and compaction. It was found that adding 10% Al2O3 significantly enhanced the hardness and wear rates of the composites. The developed LSTM-GJO algorithm showed excellent predictability of the wear rate and coefficient of friction for all considered composites.

LUBRICANTS (2022)

添加到收藏夹

Article Chemistry, Physical

Optimization of Bobbin Tool Friction Stir Processing Parameters of AA1050 Using Response Surface Methodology

Ibrahim Albaijan et al.

Summary: This research developed a statistical model using the Response Surface Method (RSM) for the bobbin tool friction stir processing (BT-FSP) of AA1050 aluminum alloy. The results indicate that the pin geometry is the most influential parameter during the BT-FSP of AA1050. The developed mathematical model accurately predicts the effects of the applied BT-FSP parameters on machine torque, processing zone temperature, surface roughness, hardness, and ultimate tensile strength.

MATERIALS (2022)

添加到收藏夹

Article Crystallography

Mechanical and Wear Properties of Al/TiC Composites Fabricated via Combined Compo-Casting and APB Process

Weining Wang et al.

Summary: The warm accumulative press bonding (APB) technique was utilized to improve the mechanical and microstructural evolution of casted Al/TiC composite bars. The results showed that the cumulative forming steps of the APB process improved the mechanical properties of the composites and resulted in a more uniform distribution of the reinforcement particles.

CRYSTALS (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Influence of high pressure torsion on microstructure evolution and mechanical properties of AZ80/SiC magnesium matrix composites

F. Akbaripanah et al.

Summary: The study investigated the effect of high pressure torsion (HPT) on an as-cast AZ80-SiC magnesium matrix composite, showing significant improvements in hardness and strength through grain refinement and texture hardening mechanisms. The results demonstrated that the first HPT turn had a more pronounced effect on hardness and strength compared to 5 and 10 turns HPT.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructural, mechanical and wear behavior of electroless assisted silver coated Al2O3-Cu nanocomposites

A. M. Sadoun et al.

Summary: Cu-Al2O3 nanocomposites were prepared by mixing Ag-coated Al2O3 nanoparticles with pure Cu powder through electro-less deposition, with excellent dispersion of Al2O3 nanoparticles achieved at high weight percentage. The addition of Ag-coated Al2O3 nanoparticles improved the density, hardness, and wear resistance of the composites, with the compressive strength reaching 33% improvement compared to pure Cu when the Al2O3 content was increased to 10 wt.%.

MATERIALS CHEMISTRY AND PHYSICS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Parameters Optimization of Dissimilar Friction Stir Welding for AA7079 and AA8050 through RSM

M. Kavitha et al.

Summary: Aluminium alloy is widely used in engineering applications and can be classified based on constituent elements. This research focused on creating a dissimilar friction stir welding joint of aluminium alloys 7079 and 8050, with tensile strength estimated using response surface methodology. The study found that the tool pin diameter had the most significant influence on the welding results.

ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2021)

添加到收藏夹

Article Materials Science, Composites

Fabrication and investigation on the properties of ilmenite (FeTiO3)-based Al composite by accumulative roll bonding

Medhat Elwan et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

添加到收藏夹

Article Materials Science, Ceramics

Structural, mechanical and tribological properties of Cu-ZrO2/GNPs hybrid nanocomposites

A. M. Sadoun et al.

CERAMICS INTERNATIONAL (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Enhanced strength and ductility of Al-SiC nanocomposites synthesized by accumulative roll bonding

Adnan Khadir et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

A mathematical modelling of preheated accumulative roll bonded Al-Al2O3 composite sheet

Abdelrahman Younis et al.

MATERIALS RESEARCH EXPRESS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Improved strength and ductility of friction stir tailor-welded blanks of base metal AA2024 reinforced with interlayer strip of AA7075

A. M. Sadoun et al.

RESULTS IN PHYSICS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Correlation between grain boundary evolution and mechanical properties of ultrafine-grained metals

Mohamed Shaat et al.

MECHANICS OF MATERIALS (2020)

添加到收藏夹

Article Materials Science, Composites

Effect of nano Al2O3coated Ag reinforced Cu matrix nanocomposites on mechanical and tribological behavior synthesis by P/M technique

A. Mohamed et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

添加到收藏夹

Article Chemistry, Physical

Effect of Asymmetric Accumulative Roll-Bonding process on the Microstructure and Strength Evolution of the AA1050/AZ31/AA1050 Multilayered Composite Materials

Sebastian Mroz et al.

MATERIALS (2020)

添加到收藏夹

Article Materials Science, Ceramics

Fabrication and evaluation of tribological properties of Al2O3 coated Ag reinforced copper matrix nanocomposite by mechanical alloying

A. Sadoun et al.

JOURNAL OF ASIAN CERAMIC SOCIETIES (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Modelling and optimisation of hardness behaviour of sintered Al/SiC composites using RSM and ANN: a comparative study

Mohammad Azad Alam et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

添加到收藏夹

Article Chemistry, Physical

Experimental and numerical investigation on strengthening mechanisms of nanostructured Al-SiC composites

A. Melaibari et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

添加到收藏夹

Article Materials Science, Composites

Investigation of mechanical properties of nanostructured Al-SiC composite manufactured by accumulative roll bonding

A. F. Meselhy et al.

JOURNAL OF COMPOSITE MATERIALS (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

The dependence of accumulative roll bonded copper mechanical properties on grain sub-division, stacking faults, and lattice strains

Ahmed Wagih et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of tool pin side area ratio on temperature distribution in friction stir welding

A. M. Sadoun et al.

RESULTS IN PHYSICS (2019)

添加到收藏夹

Article Engineering, Chemical

Design and evaluation of a novel ultrasonic desalination system by response surface methodology

Behnam Hosseingholilou et al.

DESALINATION AND WATER TREATMENT (2019)

添加到收藏夹

Article Chemistry, Physical

Sturdy, Monolithic SiC and Si3N4 Aerogels from Compressed Polymer-Cross-Linked Silica Xerogel Powders

Parwani M. Rewatkar et al.

CHEMISTRY OF MATERIALS (2018)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Significant enhancement of bond strength in the roll bonding process using Pb particles

Mohammad Heydari Vini et al.

INTERNATIONAL JOURNAL OF MATERIALS RESEARCH (2018)

添加到收藏夹

Article Chemistry, Physical

Experimental investigation on strengthening mechanisms in Al-SiC nanocomposites and 3D FE simulation of Vickers indentation

A. Wagih et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Materials Science, Ceramics

Influence of Temperature of Accumulative Roll Bonding on the Mechanical Properties of AA5083-1% Al2O3 Composite

P. Farhadipour et al.

POWDER METALLURGY AND METAL CERAMICS (2018)

添加到收藏夹

Article Automation & Control Systems

An optimization method of gating system for impeller by RSM and simulation in investment casting

Donghong Wang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Synthesis of Nanocrystalline Al2O3 Reinforced Al Nanocomposites by High-Energy Mechanical Alloying: Microstructural Evolution and Mechanical Properties

A. Wagih

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of strain path on microstructure, deformation texture and mechanical properties of nano/ultrafine grained AA1050 processed by accumulative roll bonding (ARB)

M. Naseri et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Engineering, Chemical

Mechanical properties of Al-Mg/Al2O3 nanocomposite powder produced by mechanical alloying

A. Wagih

ADVANCED POWDER TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Ceramics

An alternative method for manufacturing Al/B4C/SiC hybrid composite strips by cross accumulative roll bonding (CARB) process

Majid Naseri et al.

CERAMICS INTERNATIONAL (2015)

添加到收藏夹

Article Engineering, Multidisciplinary

Microstructure evolution and mechanical properties in ultrafine grained Al/TiC composite fabricated by accumulative roll bonding

Hamidreza Jafarian et al.

COMPOSITES PART B-ENGINEERING (2015)

添加到收藏夹

Article Engineering, Chemical

The effect of Mg add on morphology and mechanical properties of Al-xMg/10Al2O3 nanocomposite produced by mechanical alloying

A. Fathy et al.

ADVANCED POWDER TECHNOLOGY (2014)

添加到收藏夹

Article Materials Science, Ceramics

The effect of alumina content on the mechanical properties of hybrid composites fabricated by ARB process

Mohammad Reza Toroghinejad et al.

CERAMICS INTERNATIONAL (2014)

添加到收藏夹

Article Materials Science, Ceramics

Hybrid composites produced by anodizing and accumulative roll bonding (ARB) processes

Mohammad Reza Toroghinejad et al.

CERAMICS INTERNATIONAL (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of SiC nanoparticles on the mechanical properties of steel-based nanocomposite produced by accumulative roll bonding process

Roohollah Jamaati et al.

MATERIALS & DESIGN (2014)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure evolution and mechanical properties of Cu/Zn multilayer processed by accumulative roll bonding (ARB)

L. Ghalandari et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Evaluation of mechanical properties of 1060-Al reinforced with WC particles via warm accumulative roll bonding process

C. Y. Liu et al.

MATERIALS & DESIGN (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Properties of high specific strength Al-4 wt.% Al2O3/B4C nano-composite produced by accumulative roll bonding process

Morteza Alizadeh et al.

MATERIALS & DESIGN (2013)

添加到收藏夹

Article Nanoscience & Nanotechnology

Fabrication of Al/Al2O3/TiC hybrid composite by anodizing and accumulative roll bonding processes and investigation of its microstructure and mechanical properties

Hajar Farajzadeh Dehkordi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)

添加到收藏夹

Proceedings Paper Engineering, Electrical & Electronic

An experimental analysis and optimization of process parameter on friction stir welding of AA 6061-T6 aluminum alloy using RSM

G. Elatharasan et al.

INTERNATIONAL CONFERENCE ON DESIGN AND MANUFACTURING (ICONDM2013) (2013)

添加到收藏夹

Article Engineering, Manufacturing

Production of high strength Al-Al2O3 composite by accumulative roll bonding

M. Rezayat et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)

添加到收藏夹

Article Nanoscience & Nanotechnology

High-strength nanostructured Al/B4C composite processed by cross-roll accumulative roll bonding

Morteza Alizadeh et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fabrication of High-Strength Al/SiC p Nanocomposite Sheets by Accumulative Roll Bonding

M. Rezayat et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2012)

添加到收藏夹

Article Nanoscience & Nanotechnology

Investigation on microstructure and mechanical properties of Al-Zn composite during accumulative roll bonding (ARB) process

Reza Nasiri Dehsorkhi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)

添加到收藏夹

Article Chemistry, Physical

High-strength and high-conductive Cu/Ag multilayer produced by ARB

L. Ghalandari et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

添加到收藏夹

Article Chemistry, Physical

Fabrication of nanostructure Al/SiCP composite by accumulative roll-bonding (ARB) process

M. Alizadeh et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2010)

添加到收藏夹

Article Nanoscience & Nanotechnology

Comparison of nanostructured Al/B4C composite produced by ARB and Al/B4C composite produced by RRB process

Morteza Alizadeh

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

添加到收藏夹

Article Nanoscience & Nanotechnology

Manufacturing of high-strength aluminum/alumina composite by accumulative roll bonding

Roohollah Jamaati et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

添加到收藏夹

Article Materials Science, Composites

Investigation of structure and mechanical properties of multi-layered Al/Cu composite produced by accumulative roll bonding (ARB) process

M. Eizadjou et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2008)

添加到收藏夹

Article Chemistry, Physical

The evolution of microstructures and mechanical properties during accumulative roll bonding of Al/Mg composite

M. C. Chen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2006)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.