☆ 4.6 Article

Insight into Microstructure Evolution and Corrosion Mechanisms of K2ZrF6/Al2O3-Doped Hot-Dip Aluminum/Micro-Arc Oxidation Coatings

COATINGS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Metallurgy & Metallurgical Engineering

Improving corrosive wear resistance of Mg-Zn-Y-Zr alloys through heat treatment

S. D. Wang et al.

Summary: The wear resistance of an Mg-Zn-Y-Zr alloy was significantly improved after a heat treatment, regardless of the testing condition (air or NaCl solution). The dominant wear mechanism was abrasive wear accompanied by oxidation in dry sliding, while corrosive wear was dominant in the NaCl solution. The heat treatment resulted in the homogeneous distribution of fine I-phase precipitates, which enhanced the corrosive wear resistance and reduced wear, corrosion, and wear-corrosion synergy.

JOURNAL OF MAGNESIUM AND ALLOYS (2023)

添加到收藏夹

Article Materials Science, Ceramics

Effect of pore content and pH on the corrosion behavior of hydrophobic ceramic coatings

Jiahong Li et al.

Summary: Superhydrophobic ceramic coatings were successfully prepared on stainless steel substrates using the sol-gel method. The effects of pore content and pH conditions on the corrosion resistance of the hydrophobic ceramic coatings were studied. The results showed that as the porosity increased, the contact angle of the coatings increased, achieving superhydrophobic surfaces. Corrosion experiments indicated that solutions with higher pH caused greater damage to the hydrophobicity of the coatings. Additionally, the corrosion resistance of the coatings improved as their hydrophobicity increased.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Growth behavior and insulation property of the oxide layer during micro-arc oxidation of aluminium in soft regime condition

Shiyu Song et al.

Summary: Micro-arc oxidation was used to create a high voltage resistance Al2O3-based ceramic coating on aluminum alloy. The coating's microstructure and insulating properties were characterized using XRD, SEM, and breakdown voltage testers. The growth behavior and insulation property of the oxide layer under soft regime conditions were investigated. The oxide layer showed increased alpha-Al2O3 content with longer soft plasma discharge time, leading to outward growth and denser coating with improved corrosion protection. The thickness and density of the coating layer were further enhanced by soft sparks, resulting in a breakdown voltage exceeding 1000 V after 20 minutes of soft plasma discharge. The oxide layer is suggested as a potential material for insulation shielding in etching equipment.

JOURNAL OF MATERIALS SCIENCE (2023)

添加到收藏夹

Article Engineering, Biomedical

Incorporation of Al2O3 and ZrO2 ceramics to AZ31 magnesium alloys composite coating using micro-arc oxidation method

R. Askarnia et al.

Summary: A composite coating with Al2O3 and ZrO2 particles was prepared on AZ31 magnesium alloy using micro-arc oxidation (MAO) technique. The addition of ZrO2 and Al2O3 ceramic particles reduced the surface pores of the composite coating. The hardness of the coating increased from about 380 to 620 MPa with the addition of Al2O3+ZrO2 particles and the wear rate decreased about 8 times. The wettability of the coating was improved by incorporating Al2O3 and/or ZrO2 particles, with Al2O3 being more effective than ZrO2. The antibacterial properties of the MAO coatings showed that Staphylococcus aureus bacteria were more sensitive to zirconia and alumina particles than Salmonella typhimurium bacteria after 24 hours of incubation.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Mg and Si contents on hot-dip 55Al-Zn plating: Experimental and molecular dynamics simulation

Guoqiang Zhang et al.

Summary: This paper combines experiments and molecular dynamics simulations to investigate the effects and mechanisms of different Mg and Si contents in hot-dip 55Al-Zn plating on the microstructure. Both experimental and simulation results show that Mg and Si elements tend to be enriched at the substrate interface and form the Mg2Si phase. The Fe-Al intermetallic compound layer can be divided into two parts, Fe4Al13(Si, Zn) and Fe4Al13, and grows along the direction perpendicular to the substrate interface.

MATERIALS TODAY COMMUNICATIONS (2023)

添加到收藏夹

Article Chemistry, Physical

Effect of zinc or copper doping on corrosion resistance and anti-oxidative stress of strontium-based micro-arc oxidation coatings on titanium

Jingyuan Yang et al.

Summary: In this study, we created strontium/zinc and strontium/copper-doped microarc oxidation coatings on the surface of titanium implants and evaluated their corrosion resistance and osteoinductive properties under normal and oxidative stress conditions. The MAO-Sr/Zn3 group showed the best performance in terms of corrosion resistance, cell viability, mineralization, and anti-oxidative stress ability, indicating its potential for implant repair in patients with osteoporosis.

APPLIED SURFACE SCIENCE (2023)

添加到收藏夹

Article Materials Science, Ceramics

Preparation and corrosion resistance of a self-sealing hydroxyapatite- MgO coating on magnesium alloy by microarc oxidation

Cancan Liu et al.

Summary: By incorporating HA nanoparticles into the base electrolyte during the one-step microarc oxidation process, an ideal self-sealing HA-MAO coating was successfully designed. The HA nanoparticles inertly incorporated into the coating, resulting in nearly ideal sealing of micropores on the coating surface. In addition, the addition of HA nanoparticles greatly enhanced the corrosion resistance properties of the coating.

CERAMICS INTERNATIONAL (2022)

添加到收藏夹

Article Chemistry, Physical

Novel pH-responsive self-healing anti-corrosion coating with high barrier and corrosion inhibitor loading based on reduced graphene oxide loaded zeolite imidazole framework

Fei Zhong et al.

Summary: This study combines the properties of graphene and zeolite imidazole framework-8 (ZIF-8) to create a self-healing nanomaterial with excellent barrier properties and high loading rate. ZIF-8 demonstrates outstanding pH-responsive activities and high loading capacity, showing potential as a corrosion inhibitor. Salt spray test and electrochemical impedance spectroscopy results reveal that the RGO@ZIF@SiO2/EP (0.7%) sample exhibits the best corrosion protection performance.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

A self-healing corrosion protection coating with graphene oxide carrying 8-hydroxyquinoline doped in layered double hydroxide on a micro-arc oxidation coating

Yanning Chen et al.

Summary: In this study, a 8-HQ@GO composite was synthesized and incorporated into LDHs sheets, significantly improving the corrosion resistance of AZ31 alloy. The self-healing performance and anti-corrosion mechanism of the MAO-LDHs/HG coating were discussed, revealing its excellent corrosion resistance properties.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of Electrolyte Compositions and Electrical Parameters on Thermal Properties of Micro-Arc Oxidized AZ91 Alloy

Ekin Selvi et al.

Summary: This study investigates the micro-arc oxidation of AZ91 Mg alloy using different electrolytes to synthesize ZrO2 in the coatings. The results show that the thermal conductivity of the coatings can be reduced by up to 30%, mainly due to the formation of a thicker and denser coating and the incorporation of ZrO2. The increased thermal shock resistance is correlated with lower hardness and higher cohesive strength of the coatings, leading to smaller crack formation and spallation-free surface characteristics.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of Al or Mo Addition on Microstructure and Mechanical Properties of Fe-Rich Nonequiatomic FeCrCoMnNi High-Entropy Alloy

Shuliang Wang et al.

Summary: In this study, a Fe-rich nonequiatomic Fe40Cr15Co15Mn10Ni20 high-entropy alloy was prepared, and it was found that the addition of Al and Mo can effectively strengthen the alloy, but the number of intermetallic compounds should be controlled to achieve a combination of high strength and good ductility.

METALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of ageing treatment on corrosion behavior of 7075 aluminum alloy coated by micro arc oxidation (MAO)

Xing Qi et al.

Summary: The effects of ageing treatment on the corrosion behavior of 7075 aluminum alloy coated by MAO have been investigated. The results show that the precipitates formed after ageing play a significant role in the thickness, porosity, and corrosion resistance of the MAO coating. Coarse and discontinuously distributed precipitates at the grain boundary contribute to the electrochemical corrosion resistance. Decreased segregation of magnesium at the grain boundary reduces the susceptibility to stress corrosion cracking (SCC).

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of chromium on erosion-corrosion properties of ZrO2-Al2O3 particles reinforced Fe-based composites in artificial seawater slurries

Cong Li et al.

Summary: The influence of chromium on the interfacial bonding and erosion-corrosion resistance of ZrO2-Al2O3 particles reinforced high chromium white cast irons was investigated. Chromium coatings were successfully fabricated on the surface of ZTA ceramics, which resulted in improved wettability and interface bonding between ZrO2-Al2O3 particles and high chromium white cast iron matrices. The erosion-corrosion resistance of the composite materials was significantly enhanced by the addition of the chromium coating.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Corrosion resistance of MoS2-modified titanium alloy micro-arc oxidation coating

X. W. Chen et al.

Summary: The addition of MoS2 particles in the micro-arc oxidation treatment significantly improves the corrosion resistance of the Ti-6Al-4V alloy, forming a composite oxide coating with different MoS2 contents. The addition of MoS2 can effectively block the micropores of the coating, resulting in higher resistance and lower corrosion rate.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Biomedical

High proportion strontium-doped micro-arc oxidation coatings enhance early osseointegration of titanium in osteoporosis by anti-oxidative stress pathway

Xinkun Shen et al.

Summary: This study investigates the osteoinduction capabilities of a series of strontium-doped titanium implants under normal and osteoporotic conditions. The results indicate that high proportion strontium-doped coatings are more favorable for implant restorations in osteoporosis patients.

BIOACTIVE MATERIALS (2022)

添加到收藏夹

Article Energy & Fuels

Corrosion of Ni-Fe based alloy in chloride molten salts for concentrating solar power containing aluminum as corrosion inhibitor

Ming Zhu et al.

Summary: This paper studied the purification schemes of ternary chloride molten salt to prevent high-temperature corrosion of structural materials. The addition of Al powder was found to reduce the corrosion current density and form protective Al2O3 and Ni3Al layers, prolonging the lifetime of the material in the chloride molten salt.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2022)

添加到收藏夹

Article Energy & Fuels

The role of concentrated solar power with thermal energy storage in least-cost highly reliable electricity systems fully powered by variable renewable energy

Kathleen M. Kennedy et al.

Summary: Policies in the US are calling for the use of variable renewable energy sources that can reliably meet electricity demand despite fluctuations. However, the role of concentrated solar power (CSP) and thermal energy storage (TES) in comparison to photovoltaics (PV) and batteries in a highly reliable, 100% renewable system has not been clearly evaluated. This study finds that CSP and PV do not directly compete, but TES competes with short-duration battery storage. The coupled CSP+TES system can provide reliability in the absence of other grid flexibility mechanisms, and its adoption is primarily limited by high CSP generation costs.

ADVANCES IN APPLIED ENERGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Strain-shock-induced early stage high pH stress corrosion crack initiation and growth of pipeline steels

Shidong Wang et al.

Summary: This study demonstrated for the first time the strain-shock effect associated with steels having discontinuous yielding under load-control, which substantially enhanced the early stage crack initiation and growth in high pH stress corrosion cracking scenarios.

CORROSION SCIENCE (2021)

添加到收藏夹

Review Chemistry, Physical

Functionalization treatment of micro-arc oxidation coatings on magnesium alloys: a review

Zhensheng Lin et al.

Summary: The review discusses the functionalization treatment of MAO coatings on Mg alloys, aiming to enhance their antibacterial properties, corrosion resistance, biocompatibility, and bioactivity. By incorporating antibacterial metallic elements and covering with biopolymer or calcium phosphate coatings, biofunctional MAO coatings with improved corrosion resistance can be achieved.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Review Materials Science, Ceramics

Tribological mechanism of micro-arc oxidation coatings prepared by different electrolyte systems in artificial seawater

Huixia Guo et al.

Summary: Adding silicate can increase the density of the coating, and phosphate-aluminate ceramic layer exhibits the lowest wear rate in various environments. The friction coefficient and wear rate of MAO coating in seawater are lower than those in ambient air due to the boundary lubrication effect of seawater, with the presence of divalent metal salts making seawater more lubricous than other salt solutions.

CERAMICS INTERNATIONAL (2021)

添加到收藏夹

Article Computer Science, Interdisciplinary Applications

A simple unit specific event based modeling framework for short term scheduling and heat integration of batch plants: Design and optimization of heat storage vessels

Semal Sekhar Mummana et al.

Summary: Energy conservation is a prime research objective, and heat integration is a promising technique in the chemical industry. A simple unit-specific event-based framework for scheduling and heat integration is proposed, effectively handling various modelling issues with minimum equations and variables. The computational results show an optimal integration with two heat storage vessels, different from previous studies.

COMPUTERS & CHEMICAL ENGINEERING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Strain-Aging-Assisted Localized Corrosion of a Mill-Scaled X-65 Pipeline Steel

Shidong Wang et al.

Summary: The study found that strain aging can exacerbate the severity of localized corrosion in pipeline steels, leading to reduced exfoliation of oxide scales during cyclic loading and corrosion exposure, increasing galvanic corrosion between the steel and oxide scales.

CORROSION (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of hot dipping temperature on microstructure and mechanical properties of Pb40Sn60 alloy coating on copper wires

Xiaofei Yao et al.

Summary: Hot dip plating was used to prepare Pb40Sn60 alloy coating on copper wires to improve weldability and corrosion resistance. The microstructure, phase composition, and mechanical properties of the alloy coatings at different hot dipping temperatures were investigated. Results showed that increasing hot dipping temperature decreased coating thickness, increased the proportion of certain phases, and altered crystal morphology, while also reducing the strength and hardness of the copper wires.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Engineering, Environmental

A pH-responsive hydrophilic controlled release system based on ZIF-8 for self-healing anticorrosion application

Cong Yang et al.

Summary: Encapsulating corrosion inhibitors into a pH-responsive release tool, such as ZIF-8, to develop a self-healing anticorrosive coating is crucial for enhancing the protective performance of the coating. In this study, a pH-responsive hydrophilic controlled release system based on ZIF-8 was reported for waterborne EP self-healing anticorrosive coating, showing outstanding self-healing performance and increased protective performance for the coating.

CHEMICAL ENGINEERING JOURNAL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Near-neutral pH corrosion and stress corrosion crack initiation of a mill-scaled pipeline steel under the combined effect of oxygen and paint primer

Shidong Wang et al.

Summary: This study found that the combined action of oxygen and primer layer under cyclic loading increases the corrosion severity but reduces the aspect ratio of the localized corrosion areas, leading to less tendency towards pit-to-crack transition compared to the primer-coated specimen in the absence of oxygen. Various factors affecting corrosion and crack initiation have been studied.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Chemistry, Physical

Antibacterial activity of a porous silver doped TiO2 coating on titanium substrates synthesized by plasma electrolytic oxidation

Monica Thukkaram et al.

APPLIED SURFACE SCIENCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the formation of stress corrosion crack colonies with different crack population

Shidong Wang et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Near-neutral pH corrosion of mill-scaled X-65 pipeline steel with paint primer

Shidong Wang et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

添加到收藏夹

Review Chemistry, Physical

Thermal Stability of Aluminum Alloys

Frank Czerwinski

MATERIALS (2020)

添加到收藏夹

Article Electrochemistry

Corrosion Evolution of a Concrete/Casing Steel in Simulated Formation Water under Different CO2 Partial Pressures

Shuliang Wang et al.

INTERNATIONAL JOURNAL OF ELECTROCHEMICAL SCIENCE (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Development of High Temperature Oxidation Resistant Iron-Based Heat Storage Materials for Rapid Carbonization and Pulverization Process of Biomass

Daisuke Maruoka et al.

TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Enhanced corrosion resistance of micro-arc oxidation coated magnesium alloy by superhydrophobic Mg-Al layered double hydroxide coating

Zhi-hu Wang et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

添加到收藏夹

Review Energy & Fuels

Solar energy-A look into power generation, challenges, and a solar-powered future

Muhammad Badar Hayat et al.

INTERNATIONAL JOURNAL OF ENERGY RESEARCH (2019)

添加到收藏夹

Article Chemistry, Physical

Characterization of Al2O3/ZrO2 composite coatings deposited on Zr-2.5Nb alloy by plasma electrolytic oxidation

V. Malinovschi et al.

APPLIED SURFACE SCIENCE (2018)

添加到收藏夹

Article Energy & Fuels

Effect of simulated pore solution on passivation characteristic of P110 steel

Ye Peng et al.

JOURNAL OF PETROLEUM SCIENCE AND ENGINEERING (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

Influence of electrolyte composition on microstructure and properties of coatings formed on pure Ti substrate by micro arc oxidation

Wei Yang et al.

SURFACE & COATINGS TECHNOLOGY (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of phase dissolution and hydrogen absorption on the stress corrosion cracking behavior of Mg-7%Gd-5%Y-1%Nd-0.5%Zr alloy in 3.5 wt.% NaCl solution

S. D. Wang et al.

CORROSION SCIENCE (2018)

添加到收藏夹

Article Electrochemistry

A re-understanding of the breakdown theory from the study of the plasma electrolytic oxidation of a carbon steel - A non-valve metal

Zhi Li et al.

ELECTROCHIMICA ACTA (2018)

添加到收藏夹

Article Chemistry, Physical

Dual incorporation of SiO2 and ZrO2 nanoparticles into the oxide layer on 6061 Al alloy via plasma electrolytic oxidation: Coating structure and corrosion properties

S. Fatimah et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Proceedings Paper Engineering, Electrical & Electronic

Automation of the micro-arc oxidation process

P. E. Golubkov et al.

4TH INTERNATIONAL SCHOOL AND CONFERENCE ON OPTOELECTRONICS, PHOTONICS, ENGINEERING AND NANOSTRUCTURES (SAINT PETERSBURG OPEN 2017) (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Incorporation of MoO2 and ZrO2 particles into the oxide film formed on 7075 Al alloy via micro-arc oxidation

Mosab Kaseem et al.

MATERIALS LETTERS (2016)

添加到收藏夹

Article Energy & Fuels

Thermophysical property measurements and thermal energy storage capacity analysis of aluminum alloys

Gaosheng Wei et al.

SOLAR ENERGY (2016)

添加到收藏夹

Article Chemistry, Physical

Effect of ZrO2 particle on the performance of micro-arc oxidation coatings on Ti6Al4V

Hong Li et al.

APPLIED SURFACE SCIENCE (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of heat treatment on the corrosion resistance and mechanical properties of an as-forged Mg-Zn-Y-Zr alloy

S. D. Wang et al.

CORROSION SCIENCE (2015)

添加到收藏夹

Article Materials Science, Coatings & Films

High temperature oxidation behavior of TiO2 + ZrO2 composite ceramic coatings prepared by microarc oxidation on Ti6Al4V alloy

Chao Wang et al.

SURFACE & COATINGS TECHNOLOGY (2015)

添加到收藏夹

Article Chemistry, Physical

Characterization and thermal shock behavior of composite ceramic coating doped with ZrO2 particles on TC4 by micro-arc oxidation

Yesheng Zhong et al.

APPLIED SURFACE SCIENCE (2014)

添加到收藏夹

Article Materials Science, Coatings & Films

Preparation of ceramic coatings on an Al-Si alloy by the incorporation of ZrO2 particles in microarc oxidation

Chia-Jung Hu et al.

SURFACE & COATINGS TECHNOLOGY (2014)

添加到收藏夹

Review Thermodynamics

Solar power generation by PV (photovoltaic) technology: A review

G. K. Singh

ENERGY (2013)

添加到收藏夹

Article Instruments & Instrumentation

The effect of MAO processing time on surface properties and low temperature infrared emissivity of ceramic coating on aluminium 6061 alloy

Mohannad M. S. Al Bosta et al.

INFRARED PHYSICS & TECHNOLOGY (2013)

添加到收藏夹

Review Green & Sustainable Science & Technology

Solar energy: Trends and enabling technologies

Vijay Devabhaktuni et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2013)

添加到收藏夹

Article Chemistry, Physical

Preparation Al2O3/ZrO2 composite coating in an alkaline phosphate electrolyte containing K2ZrF6 on aluminum alloy by microarc oxidation

Mingqi Tang et al.

APPLIED SURFACE SCIENCE (2012)

添加到收藏夹

Article Chemistry, Physical

Characterization and mechanical properties of coatings on magnesium by micro arc oxidation

Salih Durdu et al.

APPLIED SURFACE SCIENCE (2012)

添加到收藏夹

Article Electrochemistry

Effect of cyclic oxidation on electrochemical corrosion of type 409 stainless steel in the simulated muffler condensates

Mou Cheng Li et al.

JOURNAL OF SOLID STATE ELECTROCHEMISTRY (2012)

添加到收藏夹

Proceedings Paper Materials Science, Ceramics

The Composition and Hardness of the Coating Containing Zirconia Produced by Micro-Arc Oxidation on Aluminium Alloy

Xin ShiGang et al.

HIGH-PERFORMANCE CERAMICS VII, PTS 1 AND 2 (2012)

添加到收藏夹

Article Chemistry, Physical

Evolution of micro-arc oxidation behaviors of the hot-dipping aluminum coatings on Q235 steel substrate

Lu Lihong et al.

APPLIED SURFACE SCIENCE (2011)

添加到收藏夹

Article Chemistry, Physical

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

Yuanyuan Yan et al.

APPLIED SURFACE SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Growth characteristics and corrosion resistance of micro-arc oxidation coating on pure magnesium for biomedical applications

Lichen Zhao et al.

CORROSION SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Corrosion behaviour of several aluminium alloys in contact with a thermal storage phase change material based on Glauber's salt

A. Garcia-Romero et al.

CORROSION SCIENCE (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparison of electrochemical corrosion behaviour of MgO and ZrO2 coatings on AM50 magnesium alloy formed by plasma electrolytic oxidation

J. Liang et al.

CORROSION SCIENCE (2009)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.