☆ 4.7 Article

Development of a novel wear-resistant WC-reinforced coating based on the case-hardening steel Bainidur AM for the substitution of carburizing heat treatments

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Metallurgy & Metallurgical Engineering

Directed Energy Deposition of Low-Alloyed Steels: An Insight on Microstructural and Mechanical Properties

Dominic Bartels et al.

Summary: This study investigates the material properties of low-alloyed steel Bainidur AM fabricated by DED-LB/M. The results show that the additively manufactured samples have a good combination of ductility and hardness, as well as excellent tempering stability up to 600 degrees C.

STEEL RESEARCH INTERNATIONAL (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Direct laser metal deposition cladding of IN718 on DIN 1.2714 tool steel reinforced by the SiC nanoparticles

Mojtaba Rezaee Hajideh et al.

Summary: This study investigates the effect of DLMD power and powder composition on the mechanical properties and microstructure of hot work steel forging dies. The addition of SiC nanoparticles to the DLMD powder improves wear resistance and microhardness of IN718. A higher laser power also leads to increased wear resistance and microhardness of the coating.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Automation & Control Systems

In situ modification of case-hardening steel 16MnCr5 by C and WC addition by means of powder bed fusion with laser beam of metals (PBF-LB/M)

Dominic Bartels et al.

Summary: This study investigates the design and modification of low-alloyed steel for laser-based powder bed fusion (PBF-LB/M) process by adding carbon black (C) nanoparticles and tungsten carbide (WC) particles. The results show that increasing the carbon and tungsten carbide content can enhance material hardness but adversely affect the processability. However, post-process heat treatments can achieve the desired hardness for specific applications. Additionally, the addition of tungsten carbide particles significantly improves wear resistance.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Industrial

High strength Ti alloy fabricated by directed energy deposition with in-situ Cu alloying

Jian Han et al.

Summary: A high strength Ti-6Al-4V-8.5Cu component was successfully fabricated using directed energy deposition technology, and its microstructure and performance were investigated. The addition of Cu resulted in refined grains and the presence of Cu in solid solution and Ti2Cu particles. As a result, the hardness and tensile strength of the component were significantly improved.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of cladding parameters on microstructure and defects in direct laser metal deposition of 24CrNiMo steel

Mohamad Ebrahimnia et al.

Summary: The study found that two different types of cracks can occur in multitrack clad samples, one is solidification cracks and the other is reheating cracks. By optimizing laser parameters, crackfree clad layers can be obtained through the prevention of formation of unfavorable constituents at interdendritic regions.

JOURNAL OF LASER APPLICATIONS (2021)

添加到收藏夹

Article Optics

Microstructures, wear and corrosion resistance of laser composite surfaced austenitic stainless steel (AISI 304 SS) with tungsten carbide

Amitesh Chakraborty et al.

Summary: This study successfully developed a composite surface on stainless steel through laser surface alloying, which improved the hardness and wear resistance of the material, reduced fretting wear kinetics and coefficient of friction. The formation of different carbides in the treated zone and the established mechanism of wear provide valuable insights for further research in material science.

OPTICS AND LASER TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the selection and design of powder materials for laser additive manufacturing

Carlos Donate-Buendia et al.

MATERIALS & DESIGN (2021)

添加到收藏夹

Article Chemistry, Physical

Abrasive Wear of High-Carbon Low-Alloyed Austenite Steel: Microhardness, Microstructure and X-ray Characteristics of Worn Surface

Michail Nikolaevich Brykov et al.

Summary: The high-carbon, high-silicon steel was quenched at different temperatures and subjected to abrasive wear tests, which showed higher microhardness on surfaces after three-body abrasion compared to two-body abrasion. The differences in microhardness were attributed to variations in wear conditions and stability of retained austenite.

MATERIALS (2021)

添加到收藏夹

Article Engineering, Manufacturing

Effect of tungsten particles on microstructure and properties of 316 L stainless steel manufactured by selective laser melting

Xiaotian Yin et al.

Summary: This study developed reinforced 316L SS composites through SLM with the addition of tungsten particles, leading to significant improvements in mechanical and corrosion properties. The 10 wt% W/316L SS composites showed over 50% increase in yield strength, along with notable increases in hardness and elongation.

JOURNAL OF MANUFACTURING PROCESSES (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Thermal model for the directed energy deposition of composite coatings of 316L stainless steel enriched with tungsten carbides

Seifallah Fetni et al.

Summary: This study focuses on developing a finite element model to predict the thermal history and melt pool dimension evolution in the middle section of the clad; experimental analysis confirmed the importance of forced convection in the boundary conditions to maintain balance between input energy and heat loss; the research shows a slight increase trend in maximum peak temperature for the first few layers, followed by stabilization.

MATERIALS & DESIGN (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Carburizing Heat Treatment of Selective-Laser-Melted 20MnCr5 Steel

Mei Yang et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

添加到收藏夹

Article Optics

Effect of tungsten carbide partial dissolution on the microstructure evolution of a laser clad surface

F. Fazliana et al.

OPTICS AND LASER TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation on the Case-Hardening Behavior of Additively Manufactured 16MnCr5

Dominic Bartels et al.

METALS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Austenite stability and deformation-induced transformation mechanism in cold-rolled medium-Mn steel

T. P. Zhou et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Engineering, Mechanical

Deformation behavior and dominant abrasion micro mechanisms of tempering steel with varying carbon content under controlled scratch testing

F. Poehl et al.

WEAR (2019)

添加到收藏夹

Article Engineering, Mechanical

Scratch-tip-size effect and change of friction coefficient in nano/micro scratch tests using XFEM

Kwangmin Lee et al.

TRIBOLOGY INTERNATIONAL (2018)

添加到收藏夹

Article Engineering, Mechanical

Three-body abrasive wear of carbide-free bainite, martensite and bainite-martensite structure of similar hardness

Minal Shah et al.

WEAR (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Additive manufacturing of compositionally gradient metal-ceramic structures: Stainless steel to vanadium carbide

Thomas Gualtieri et al.

MATERIALS & DESIGN (2018)

添加到收藏夹

Article Engineering, Manufacturing

The Role of Reinforcing Particle Size in Tailoring Interfacial Microstructure and Wear Performance of Selective Laser Melting WC/Inconel 718 Composites

Qimin Shi et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Processing of AISI H11 Tool Steel Powder Modified with Carbon Black Nanoparticles for the Additive Manufacturing of Forging Tools with Tailored Mechanical Properties by Means of Laser Metal Deposition (LMD)

Oliver Hentschel et al.

METALS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Characterization of stainless steel parts by Laser Metal Deposition Shaping

Kai Zhang et al.

MATERIALS & DESIGN (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Bainite and martensite start temperature calculated with exponential carbon dependence

S. M. C. van Bohemen

MATERIALS SCIENCE AND TECHNOLOGY (2012)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

On the Precipitation Sequence in a 10%Cr Steel under Tempering

Nadezhda Dudova et al.

ISIJ INTERNATIONAL (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of tungsten addition on microstructure and high temperature strength of 9CrODS ferritic steel

T. Narita et al.

JOURNAL OF NUCLEAR MATERIALS (2011)

添加到收藏夹

Article Engineering, Chemical

Possibility of the Abrasive Wear Resistance Determination with Scratch Tester

A. Vencl et al.

TRIBOLOGY LETTERS (2010)

添加到收藏夹

Article Materials Science, Coatings & Films

Characterization of in situ synthesized TiC particle reinforced Fe-based composite coatings produced by multi-pass overlapping GTAW melting process

X. H. Wang et al.

SURFACE & COATINGS TECHNOLOGY (2007)

添加到收藏夹

Article Materials Science, Coatings & Films

Plasma carburizing process for the low distortion of automobile gears

JM Baek et al.

SURFACE & COATINGS TECHNOLOGY (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.