☆ 4.7 Article

Friction stir powder additive manufacturing of Al 6061 alloy: Enhancing microstructure and mechanical properties by reducing thermal gradient

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Solid-state cold spray additive manufacturing of pure tantalum with extraordinary high-temperature mechanical properties

Young-Kyun Kim et al.

Summary: Solid-state cold spray additive manufacturing (CSAM) was used to fabricate pure tantalum (Ta) and its high-temperature mechanical and deformation behavior were investigated. The CSAM-fabricated Ta consisted of irregularly shaped, elongated powder particles perpendicular to the spraying direction. Microstructural evolution occurred along the boundaries between powder particles in response to harsher plastic deformation. Compression test results showed that the room temperature yield strength of CSAM Ta was approximately 901 MPa, significantly higher than conventional Ta processes. Furthermore, CSAM Ta exhibited excellent mechanical properties at high temperatures up to approximately 950 degrees C, attributed to the interaction between high-temperature oxidation behavior and microstructural evolution, i.e. dynamic recrystallization. The relationship between microstructure, room-to-high-temperature mechanical properties, and deformation behaviors are discussed.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructure and Properties of Solid-state Additive Manufactured Mg-10Li-3Al-3Zn Magnesium Alloy

Jie Yao et al.

Journal of Materials Research and Technology-JMR&T (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Interface microstructure and mechanical properties of copper-steel joints with nickel transition layer prepared by ultrasonic additive manufacturing

Bo Wang et al.

Summary: To solve the problems of intergranular copper infiltration, liquid phase separation, and thermal cracks during fusion welding of copper and 304 stainless steel, UAM technology was used to consolidate a nickel transition layer on the stainless steel surface for surface modification. Copper-304 stainless steel overlap joints were obtained using the pulse TIG process. The study found that the introduction of a nickel interlayer can achieve metallurgical isolation between copper and steel and relieve interfacial stress. A high-quality brazed joint with a nickel interlayer thickness of 0.1 mm was formed between stainless steel and copper, with an ultimate tensile strength of 165 MPa at room temperature. The joint fracture occurred near the fusion line close to the copper side, showing a ductile fracture mode.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Engineering, Industrial

Friction stir powder additive manufacturing of Al 6061/FeCoNi and Al 6061/Ni metal matrix composites: Reinforcement distribution, microstructure, residual stresses, and mechanical properties

Bhavesh Chaudhary et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2023)

添加到收藏夹

Article Engineering, Manufacturing

Material flow path and extreme thermomechanical processing history during additive friction stir deposition

Nikhil Gotawala et al.

Summary: By combining theoretical and experimental methods, we have developed an experimentally-informed modeling framework that reveals the three-dimensional flow path of the material and quantifies the thermal and deformation history. The study shows that the feed material undergoes extreme thermomechanical processing during AFSD, with high temperatures and significant strain rates. The resulting microstructure is uniform and has been verified experimentally.

JOURNAL OF MANUFACTURING PROCESSES (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and interface evolution of diamond/ Cu composites prepared via ultrasonic additive manufacturing (UAM)

Bo Wang et al.

Summary: Diamond-copper laminated composites with Cr-coating were prepared using ultrasonic additive manufacturing method. The microstructure and interfacial configuration between Cr-diamond and copper matrix were analyzed using various microscopy techniques. The study revealed excellent solid bonding between Cr-diamond and the matrix, with significant grain refinement and dynamic recrystallization at the interface. These composites exhibited high thermal conductivity and could open up new possibilities in low-temperature, low-pressure, free-design, and open fabrication of particle-reinforced metal matrix composites.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Fretting Wear and Corrosion Behaviour of an Al-ZrO2/Ni Hybrid Composite Developed by Friction Stir Processing

Mahesh Patel et al.

Summary: This paper studied the fretting wear and fretting corrosion behavior of AA6063 alloys and hybrid AA6063 matrix composites (HAMCs). The results showed that HAMCs exhibited higher fretting corrosion resistance compared to the base material.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of the Tool Pin Eccentricity and Cooling Rate on Microstructure, Mechanical Properties, Fretting Wear, and Corrosion Behavior of Friction Stir Processed AA6063 Alloy

Mahesh Patel et al.

Summary: FSP with 0.6 mm pin eccentricity and high cooling rate can enhance the performance of AA6063 alloy by preventing grain coarsening and resulting in a fine grain structure.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Highly tunable multifunctional rare earth based Bi0.5-xCexNa0.5TiO3 perovskites via site selective doping engineering

Subramani Supriya

Summary: High-quality lead-free relaxor-ferroelectric BCNT electroceramics were fabricated using the modified Pechini method, and the influence of cerium dopant on the material properties was studied. The doping affected the density and sintering temperature, but had a positive effect on crystallinity. BCNT ceramics showed increased grain size and significant changes in shrinkage, making them suitable for commercial applications such as electrode systems and multi-layered structures.

MATERIALS CHEMISTRY AND PHYSICS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Feasibility of multilayer solid-state deposition via lateral friction surfacing for metal additive manufacturing

Ebrahim Seidi et al.

Summary: Lateral friction surfacing is a novel solid-state deposition process that offers an alternative for creating thin and ultra-smooth metallic deposit layers. The study explored material transfer to the substrate through multiple passes of the tool, resulting in a steady-state deposit thickness. Various analyses were conducted to characterize the process and the fabricated deposits.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Automation & Control Systems

Experimental investigation and parametric optimization of friction stir powder additive manufacturing process for aerospace-grade Al alloy

Bhavesh Chaudhary et al.

Summary: This paper presents experimental investigation on friction-stir powder additive manufacturing (FSPAM) process for aerospace-grade aluminum alloy Al 6061 powder and the identification of its optimum parameters using grey relational analysis (GRA). The study shows that FSPAM is a viable alternative to fusion-based additive manufacturing processes for aluminum alloys, with refinements in grain size and uniform distribution of alloying elements. The findings provide insights into the optimization of FSPAM process parameters for improved surface quality and integrity.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

添加到收藏夹

Review Engineering, Manufacturing

A review on metal additive manufacturing for intricately shaped aerospace components

Vaishnav Madhavadas et al.

Summary: Additive manufacturing is a rapidly growing industrial technique that brings innovative solutions to various manufacturing problems. In the aerospace industry, additive manufacturing is particularly advantageous for producing complex structures and alloys with a high strength-to-weight ratio. This review comprehensively discusses the application of additive manufacturing in the aerospace industry, including different techniques, comparison with conventional methods, and future prospects.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Chemistry, Physical

Comparison between layered Pt3Te4 and PtTe2 for electrocatalytic reduction reactions

Subramani Supriya et al.

Summary: In this study, layered Pt3Te4 and PtTe2 were successfully synthesized and characterized, showing promising electrocatalytic properties for hydrogen evolution and oxygen reduction reactions. The direct synthesis of these compounds from respective elements resulted in monoclinic and trigonal crystal structures, indicating potential applications in future catalysis.

FLATCHEM (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Wear Dry Behavior of the Al-6061-Al2O3 Composite Synthesized by Mechanical Alloying

Victor Hugo Mercado-Lemus et al.

Summary: The study compares the wear behavior of a mechanically milled Al-6061 alloy and the same alloy reinforced with 5 wt.% of Al2O3 nanoparticles under different dry sliding conditions. Results show that the aluminum matrix composite (Al-6061-Al2O3) exhibits improved wear resistance due to the presence of nanoparticles. The strengthening mechanisms mainly lie in a nanometric size and homogeneous dispersion of particles.

METALS (2021)

添加到收藏夹

Article Engineering, Industrial

Solid-state cladding on thin automotive sheet metals enabled by additive friction stir deposition

W. Douglas Hartley et al.

Summary: Additive friction stir deposition can produce high-quality cladding without porosity even in thin substrates as thin as 1.4 mm, preserving the original strength and formability of the substrate. Despite mild global substrate distortion during cooling, the system reconfigures itself to minimize potential energy and reduce residual stress.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

添加到收藏夹

Review Engineering, Manufacturing

Metal additive manufacturing using friction stir engineering: A review on microstructural evolution, tooling and design strategies

Sandeep Rathee et al.

Summary: Solid state metal additive manufacturing techniques based on friction stir engineering have gained attention as a bridge for existing MAM shortfalls in the past decade. This article discusses SS-MAM techniques such as additive friction stir and friction stir additive manufacturing, focusing on tooling, fundamentals, recent developments, metallurgy, microstructural aspects, mechanical properties, timeline, utilization for different applications, and recent trends in depth.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Experimental and numerical studies on fabrication of nanoparticle reinforced aluminum matrix composites by friction stir additive manufacturing

Zhijun Tan et al.

Summary: Friction stir additive manufacturing (FSAM) is used to fabricate nanoparticle reinforced aluminum matrix composites, optimizing material properties in terms of hardness and grain size. The dispersion of nanoparticles increases hardness and reduces grain size, while re-stirring and reheating in the stirring zone improves mechanical properties. Both nanoparticle size and volume fraction have significant effects on grain size and hardness.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Review Engineering, Manufacturing

Innovative potential of additive friction stir deposition among current laser based metal additive manufacturing processes: A review

Vipin Gopan et al.

Summary: This review focuses on the key findings and advantages of additive friction stir deposition (AFSD) technology, emphasizing microstructure evolution and physical properties. AFSD, as a promising technique, offers benefits such as improved mechanical properties, reduced defects, increased build rate, and cost savings.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Solid-state additive manufacturing high performance aluminum alloy 6061 enabled by an in-situ micro-forging assisted cold spray

Ying-Kang Wei et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Cold spray deposition of solution heat treated, artificially aged and naturally aged Al 7075 powder

Alexandre Sabard et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Industrial

Mechanical and microstructural characterization of aluminium powder deposit made by friction stir based additive manufacturing

Akash Mukhopadhyay et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure-strength relationship in friction-stir welded 6061-T6 aluminum alloy

Alexander Kalinenko et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

添加到收藏夹

Article Engineering, Manufacturing

Fabrication of a nanostructured high strength steel tube by friction-forging tubular additive manufacturing (FFTAM) technology

H. Aghajani Derazkola et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

添加到收藏夹

Review Materials Science, Multidisciplinary

Effects of porosity on the mechanical properties of additively manufactured components: a critical review

Ahmad Y. Al-Maharma et al.

MATERIALS RESEARCH EXPRESS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Friction-forging tubular additive manufacturing (FFTAM): A new route of solid-state layer-upon-layer metal deposition

H. Aghajani Derazkola et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

添加到收藏夹

Article Engineering, Manufacturing

Interfacial bonding features of friction stir additive manufactured build for 2195-T8 aluminum-lithium alloy

Zijun Zhao et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

添加到收藏夹

Article Chemistry, Physical

Simultaneously Enhanced Strength and Ductility of Al-Mg-Si Alloys during Aging Process Induced by Electro-Pulsing Treatment

Yitong Wang et al.

MATERIALS (2019)

添加到收藏夹

Review Materials Science, Multidisciplinary

3D printing of Aluminium alloys: Additive Manufacturing of Aluminium alloys using selective laser melting

Nesma T. Aboulkhair et al.

PROGRESS IN MATERIALS SCIENCE (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure-deformation relationship of additive friction stir-deposition Al-Mg-Si

B. J. Phillips et al.

MATERIALIA (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

High ductility aluminum alloy made from powder by friction extrusion

Scott Whalen et al.

MATERIALIA (2019)

添加到收藏夹

Article Automation & Control Systems

Friction stir consolidation of aluminum machining chips

X. Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

添加到收藏夹

Review Materials Science, Multidisciplinary

Additive manufacturing of metallic components - Process, structure and properties

T. DebRoy et al.

PROGRESS IN MATERIALS SCIENCE (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Non-beam-based metal additive manufacturing enabled by additive friction stir deposition

Hang Z. Yu et al.

SCRIPTA MATERIALIA (2018)

添加到收藏夹

Review Materials Science, Multidisciplinary

Anisotropy and heterogeneity of microstructure and mechanical properties in metal additive manufacturing: A critical review

Y. Kok et al.

MATERIALS & DESIGN (2018)

添加到收藏夹

Review Engineering, Manufacturing

Potentials and strategies of solid-state additive friction-stir manufacturing technology: A critical review

F. Khodabakhshi et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of sintering temperature and micro structural analysis on sol-gel derived silver bismuth titanate ceramics

S. Supriya

MATERIALS RESEARCH BULLETIN (2017)

添加到收藏夹

Article Engineering, Manufacturing

A new process for design and manufacture of tailor-made functionally graded composites through friction stir additive manufacturing

Abhay Sharma et al.

JOURNAL OF MANUFACTURING PROCESSES (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Growth of NaDP-GPI single crystal and its analysis on basis of HRXRD, optical and mechanical studies

S. Supriya et al.

MATERIALS LETTERS (2014)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructure and Mechanical Properties of AlSi10Mg Parts Produced by the Laser Beam Additive Manufacturing (AM) Technology

Idan Rosenthal et al.

METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2014)

添加到收藏夹

Article Engineering, Industrial

Characterisation of the cold metal transfer (CMT) process and its application for low dilution cladding

C. G. Pickin et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)

添加到收藏夹

Article Engineering, Mechanical

Friction and wear characteristics due to stick-slip under fretting conditions

Sung-Hoon Jeong et al.

TRIBOLOGY TRANSACTIONS (2007)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.