☆ 4.5 Article

Effect of Cu Content on the PBF-LB/M Processing of the Promising Al-Si-Cu-Mg Composition

METALS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Review Chemistry, Physical

Ongoing Challenges of Laser-Based Powder Bed Fusion Processing of Al Alloys and Potential Solutions from the Literature-A Review

Alessandra Martucci et al.

Summary: The high strength-to-weight ratio, corrosion resistance and conductivity of aluminium alloys have increased their popularity in laser-based powder bed fusion production. However, the challenges of solidification shrinkage, oxidation, laser reflectivity and powder flowability hinder their processing in additive manufacturing. Therefore, the development of new tailored aluminium alloys is necessary.

MATERIALS (2023)

添加到收藏夹

Review Chemistry, Physical

Research Progress on Multi-Component Alloying and Heat Treatment of High Strength and Toughness Al-Si-Cu-Mg Cast Aluminum Alloys

Mingshan Zhang et al.

Summary: Al-Si-Cu-Mg cast aluminum alloys are widely used in automobile lightweight due to their high strength-to-weight ratio, good heat resistance, and excellent casting performance. Enhancing the strength and toughness of these alloys through multi-component alloying and heat treatment is an effective way to promote their application in automotive parts. This paper provides an overview of the research progress in this field and presents the development prospects of lightweight Al-Si-Cu-Mg cast aluminum alloys for automobiles.

MATERIALS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Improvement in the PBF-LB/M processing of the Al-Si-Cu-Mg composition through the use of pre-alloyed powder

A. Martucci et al.

Summary: Among additive manufacturing technologies, Powder Bed Fusion-Laser Beam (PBF-LB/M) is known for its ability to produce complex-shaped functional parts. However, the materials available for PBF-LB/M are limited, and research into new high-performance Al-based alloys is ongoing. One promising solution is the use of pre-alloyed powders, which have shown better performance compared to mixed powders in terms of microstructure and mechanical properties.

MATERIALS RESEARCH EXPRESS (2023)

添加到收藏夹

Article Engineering, Manufacturing

Effect of process parameters and grain refinement on hot tearing susceptibility of high strength aluminum alloy 2139 in laser powder bed fusion

Joe Elambasseril et al.

Summary: High strength aluminum alloys are widely used in transport and aerospace industries, but their additive manufacturing can be challenging due to hot tearing. This study investigated the elimination of hot tearing in Al2139 alloy through process parameter selection and the addition of a grain refiner. The research found that increased energy density and grain refinement can reduce or eliminate hot tearing in Al2139 during laser powder bed fusion manufacturing.

PROGRESS IN ADDITIVE MANUFACTURING (2022)

添加到收藏夹

Review Materials Science, Multidisciplinary

Fluidity of casting Al-Si series alloys for automotive light-weighting: a systematic review

Guodong Niu et al.

Summary: This review systematically summarizes the factors influencing the fluidity of casting Al-Si series alloys and discusses the solidification mechanism of hypoeutectic Al-Si alloys under the high-pressure die casting (HPDC) process. It explains that fluidity length increases with decreasing solidus temperature of the hypoeutectic Al-Si alloys.

MATERIALS SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Multidisciplinary Sciences

The interplay between vapour, liquid, and solid phases in laser powder bed fusion

I. Bitharas et al.

Summary: In this study, the authors directly investigated the impact of laser-material interaction on laser powder bed fusion (LPBF) process using simultaneous in-situ synchrotron x-ray and schlieren imaging. By quantifying the morphological changes during the process, the instability of the process was revealed, and the effect of the powder layer on process stability was explored. These findings contribute to the design of process windows at higher power and speed, and provide a potential method for monitoring process stability.

NATURE COMMUNICATIONS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Synergic strategies to improve the PBF-LB\M processability of a cracking-sensitive alloy

A. Martucci et al.

Summary: Powder Bed Fusion-Laser Beam/Metals (PBF-LB/M) is a promising additive manufacturing process for producing functional components with complex shapes. However, the high thermal gradient and thermally induced stresses during the layer-by-layer scanning and high cooling rates can lead to undesirable cracking and delamination. This study aims to investigate strategies for processing non-standard compositions and found that the synergistic use of appropriate process parameters and support structures can prevent cracking and achieve fully dense specimens, even without platform heating.

MATERIALS & DESIGN (2022)

添加到收藏夹

Article Chemistry, Physical

Composition design method of Al-Cu alloy for laser powder bed fusion

Renyi Lu et al.

Summary: In this study, an Al-Cu alloy suitable for laser powder bed fusion was developed rapidly through casting and laser remelting. The alloy showed refined microstructure and improved hardness after remelting. By optimizing the alloy composition, the remelted Al-5Cu-2Mg-1Zr-0.3Mn-0.15Ti alloys exhibited excellent mechanical properties after LPBF forming and solution treatment.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

The hot deformation behaviour of laser powder bed fusion deposited Al-Si-Cu alloy processed by high-pressure torsion

Ahmed S. J. Al-Zubaydi et al.

Summary: The tensile properties of an ultrafine-grained Al-9%Si-3%Cu alloy deposited by the laser powder bed fusion process were investigated in this study. The processed alloy exhibited higher strength and elongation, and the room temperature processing improved the microstructure of the alloy.

JOURNAL OF MATERIALS SCIENCE (2022)

添加到收藏夹

Article Chemistry, Physical

Composition design method of Al-Cu alloy for laser powder bed fusion

Renyi Lu et al.

Summary: In this study, an Al-Cu alloy suitable for laser powder bed fusion (LPBF) was developed rapidly through casting and laser remelting, achieving refined microstructure and improved hardness. The effects of different element content on alloy properties were analyzed, leading to the determination of an optimum composition. The remelted alloy exhibited excellent performance in terms of hardness, tensile strength, and yield strength.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Structure and mechanical properties of an advanced aluminium alloy AlSi10MgCu(Ce,Zr) produced by selective laser melting

N. V. Dynin et al.

Summary: The article investigates the structure and mechanical properties of an advanced aluminum alloy produced by selective laser melting. The alloy exhibits high strength and good elongation in both T6 and annealed states.

MATERIALS LETTERS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

The Influence of Particle Shape, Powder Flowability, and Powder Layer Density on Part Density in Laser Powder Bed Fusion

Lukas Haferkamp et al.

Summary: This study examined the influence of particle shape on final part density in laser powder bed fusion, finding correlations between powder properties and their impact on part density. However, improvements in powder shape beyond a certain threshold did not lead to higher final part density.

METALS (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Heat treatment of aluminium alloys produced by laser powder bed fusion: A review

J. Fiocchi et al.

Summary: Laser powder bed fusion (LPBF) is a widely used additive manufacturing technique for producing aluminium alloys, which has attracted attention due to its low density. The peculiar solidification conditions and layer-by-layer construction during the SLM process result in various microstructural features, requiring special post-build heat treatments to adapt to the unique metallurgy and address specific issues.

MATERIALS & DESIGN (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Coated Metal Powders for Laser Powder Bed Fusion (L-PBF) Processing: A Review

Robert Bidulsky et al.

Summary: Functionalized powders have gained increasing interest in additive manufacturing, particularly in terms of improved flowability and enhanced processability, as well as potential higher final mechanical or physical properties. Coatings represent an interesting approach for powder functionalizing, with various methods studied in recent years. This work provides an overview of coated powders, analyzing production processes, processability, and properties of final parts obtained through L-PBF.

METALS (2021)

添加到收藏夹

Article Multidisciplinary Sciences

Unravelling the multi-scale structure-property relationship of laser powder bed fusion processed and heat-treated AlSi10Mg

P. Van Cauwenbergh et al.

Summary: The study uncovers the relationship between the microstructure and macroscopic material properties of LPBF-processed AlSi10Mg, identifying grain refinement and Si supersaturation as crucial elements for achieving superior mechanical and thermal properties during heat treatment. Additionally, an electrical conductivity model accurately predicts Si solute concentration in LPBF-processed and heat-treated AlSi10Mg, facilitating understanding of microstructural evolution during heat treatment. The LPBF-processed and heat-treated AlSi10Mg conditions exhibit a range of superior mechanical properties compared to the mould-cast T6 reference condition.

SCIENTIFIC REPORTS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of the heat treatment on the microstructure and hardness evolution of a AlSi10MgCu alloy designed for laser powder bed fusion

A. Martin et al.

Summary: The addition of Cu has a significant influence on the microhardness of the L-PBF-fabricated AlSi10MgCu alloy, exceeding 180 HV and showing similar levels of strength to Al7075. Analytical transmission electron microscopy revealed that Cu contributes to reducing the Al-matrix cell size, increasing the density of Si-based nanoprecipitates, and decreasing their size.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of ultrasonic and different modification treatments on the microstructure of cast Al-Si-Cu-Mg-Ni alloy

Jia Wang et al.

Summary: The study improved the microstructure of Al-Si alloys by adding different modifiers and applying ultrasonic melt treatment. The results showed that the Al-2P master alloy modifier had a more stable effect compared to the phosphorus modifier, which required a higher amount for similar refinement results. The ultrasonic treatment was found to be more effective for phosphorus modification.

PHILOSOPHICAL MAGAZINE (2021)

添加到收藏夹

Article Chemistry, Physical

An Automatic on Top Analysis of Single Scan Tracks to Evaluate the Laser Powder Bed Fusion Building Parameters

Alessandra Martucci et al.

Summary: The production of dense samples using laser powder bed fusion (LPBF) relies on the optimal combination of construction parameters, with parameter optimization being the first step in defining the LPBF process. Research utilizing the single scan track (SST) approach aims to narrow down ranges of laser power and scan speed values for mass production. By implementing an innovative algorithm for SST characterization and quality evaluation, it is possible to easily identify the process parameter window that allows for the production of dense samples.

MATERIALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Rapid Solidification and Non-equilibrium Phase Constitution in Laser Powder Bed Fusion (LPBF) of AlSi10Mg Alloy: Analysis of Nano-precipitates, Eutectic Phases, and Hardness Evolution

Hong Qin et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

添加到收藏夹

Article Automation & Control Systems

Laser metal deposition of copper on diverse metals using green laser sources

Himani Siva Prasad et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Selective laser melting of high-strength primary AlSi9Cu3 alloy: Processability, microstructure, and mechanical properties

J. Fiocchi et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

A time-saving and cost-effective method to process alloys by Laser Powder Bed Fusion

Federico Bosio et al.

MATERIALS & DESIGN (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Evaluation of solidification cracking susceptibility during laser welding in advanced high strength automotive steels

G. Agarwal et al.

MATERIALS & DESIGN (2019)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Metallographic Studies of Dissimilar Al-Cu Laser-Welded Joints Using Various Etchants

Pascal Schmalen et al.

METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

The structural and compositional evolution of precipitates in Al-Mg-Si-Cu alloy

Lipeng Ding et al.

ACTA MATERIALIA (2018)

添加到收藏夹

Article Chemistry, Physical

Microstructure and mechanical properties of hierarchical multi-phase composites based on Al-Ni-type intermetallic compounds in the Al-Ni-Cu-Si alloy system

J. T. Kim et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Chemistry, Physical

A comparison of Selective Laser Melting with bulk rapid solidification of AlSi10Mg alloy

Silvia Marola et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Chemistry, Physical

Influence of Powder Characteristics on Processability of AlSi12 Alloy Fabricated by Selective Laser Melting

Rustam Baitimerov et al.

MATERIALS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Manufacturability of AlSi10Mg overhang structures fabricated by laser powder bed fusion

Quanquan Han et al.

MATERIALS & DESIGN (2018)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

The evolution of structural and chemical heterogeneity during rapid solidification at gas atomization

V. M. Golod et al.

INTERNATIONAL CONFERENCE STRUCTURAL AND PHASE TRANSFORMATIONS IN MATERIALS: THEORY, COMPUTER MODELLING AND EXPERIMENT (2017)

添加到收藏夹

Review Engineering, Manufacturing

Powder characterisation techniques and effects of powder characteristics on part properties in powder-bed fusion processes

Austin T. Sutton et al.

VIRTUAL AND PHYSICAL PROTOTYPING (2017)

添加到收藏夹

Article Thermodynamics

Calorimetric measurements and assessment of the binary Cu-Si and ternary Al-Cu-Si phase diagrams

Bengt Hallstedt et al.

CALPHAD-COMPUTER COUPLING OF PHASE DIAGRAMS AND THERMOCHEMISTRY (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Rapid Solidification: Selective Laser Melting of AlSi10Mg

Ming Tang et al.

JOM (2016)

添加到收藏夹

Article Thermodynamics

Thermal conductivity of Al-Cu-Mg-Si alloys: Experimental measurement and CALPHAD modeling

Cong Zhang et al.

THERMOCHIMICA ACTA (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

A selective laser melting and solution heat treatment refined Al-12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility

X. P. Li et al.

ACTA MATERIALIA (2015)

添加到收藏夹

Article Engineering, Industrial

Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg

Christian Weingarten et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)

添加到收藏夹

Article Engineering, Industrial

Influence of process-induced microstructure and imperfections on mechanical properties of AlSi12 processed by selective laser melting

Shafaqat Siddique et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)

添加到收藏夹

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of Al-12Si produced by selective laser melting: Effect of heat treatment

K. G. Prashanth et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Effect of Ce on morphology of alpha(Al)-Al2Cu eutectic in Al-Si-Cu alloy

Maja Voncina et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder

Lore Thijs et al.

ACTA MATERIALIA (2013)

添加到收藏夹

Article Engineering, Industrial

Influence of ultrasonic melt treatment on microstructure and mechanical properties of AlSi9Cu3 alloy

H. Puga et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2011)

添加到收藏夹

Article Thermodynamics

Dependency of the thermal and electrical conductivity on the temperature and composition of Cu in the Al based Al-Cu alloys

S. Aksoz et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

Age-hardening behavior of cast Al-Si base alloy

RX Li et al.

MATERIALS LETTERS (2004)

添加到收藏夹

Article Nanoscience & Nanotechnology

Diffusion coefficients of some solutes in fcc and liquid Al: critical evaluation and correlation

Y Du et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.