相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Strengthening Mechanisms and Strain Hardening Behavior of 316L Stainless Steel Manufactured by Laser-Based Powder Bed Fusion
Aliakbar Taghipour et al.
ADVANCED ENGINEERING MATERIALS (2023)
Mechanical properties and microstructural characteristics of 316L stainless steel fabricated by laser powder bed fusion and binder jetting
Mengchen Xu et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)
Microstructures and Mechanical Properties of Steels and Alloys Subjected to Large-Strain Cold-to-Warm Deformation
Anastasiia Dolzhenko et al.
METALS (2022)
Cryogenic impact toughness of a work hardened austenitic stainless steel
M. V. Odnobokova et al.
MATERIALIA (2022)
Effect of initial dislocation density on the plastic deformation response of 316L stainless steel manufactured by directed energy deposition
Shi-Hao Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)
Study of Material Properties and Creep Behavior of a Large Block of AISI 316L Steel Produced by SLM Technology
Sarka Hermanova et al.
METALS (2022)
Strength Properties of 316L and 17-4 PH Stainless Steel Produced with Additive Manufacturing
Slawomir Kedziora et al.
MATERIALS (2022)
Subgrain microstructures and tensile properties of 316L stainless steel manufactured by selective laser melting
Xin Yang et al.
JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2021)
On the Strength of a 316L-Type Stainless Steel Subjected to Cold or Warm Rolling Followed by Annealing
Marina Odnobokova et al.
MATERIALS (2020)
The Influence of Heat Treatment on Low Cycle Fatigue Properties of Selectively Laser Melted 316L Steel
Janusz Kluczynski et al.
MATERIALS (2020)
Grain refinement and strengthening of austenitic stainless steels during large strain cold rolling
Marina Odnobokova et al.
PHILOSOPHICAL MAGAZINE (2019)
High Strength and Ductility of Additively Manufactured 316L Stainless Steel Explained
Md. Shamsujjoha et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)
Mechanical behavior of selective laser melted 316L stainless steel
Jyoti Suryawanshi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
On the effect of chemical composition on yield strength of TWIP steels
Pavel Kusakin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)
Hall-Fetch relationship for austenitic stainless steels processed by large strain warm rolling
Z. Yanushkevich et al.
ACTA MATERIALIA (2017)
Microstructural evolution of a 304-type austenitic stainless steel during rolling at temperatures of 773-1273 K
Zhanna Yanushkevich et al.
ACTA MATERIALIA (2015)
Effect of Severe Cold or Warm Deformation on Microstructure Evolution and Tensile Behavior of a 316L Stainless Steel
Marina Odnobokova et al.
ADVANCED ENGINEERING MATERIALS (2015)
Applying the texture analysis for optimizing thermomechanical treatment of high manganese twinning-induced plasticity steel
Christian Haase et al.
ACTA MATERIALIA (2014)
Microstructure evolution and strengthening mechanisms of Fe-23Mn-0.3C-1.5Al TWIP steel during cold rolling
Pavel Kusakin et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Microstructure and Strengthening Mechanisms in an Ultrafine Grained Al-Mg-Sc Alloy Produced by Powder Metallurgy
Tammy J. Harrell et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions
Taku Sakai et al.
PROGRESS IN MATERIALS SCIENCE (2014)
The effects of N on the microstructures and tensile properties of Fe-15Mn-0.6C-2Cr-xN twinning-induced plasticity steels
Yeon-Seung Jung et al.
ACTA MATERIALIA (2013)
On the Relation of Microstructure and Texture Evolution in an Austenitic Fe-28Mn-0.28C TWIP Steel During Cold Rolling
Christian Haase et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
Multistage strain hardening through dislocation substructure and twinning in a high strength and ductile weight-reduced Fe-Mn-Al-C steel
I. Gutierrez-Urrutia et al.
ACTA MATERIALIA (2012)
Effect of large strain cold rolling and subsequent annealing on microstructure and mechanical properties of an austenitic stainless steel
I. Shakhova et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD
Marion Calcagnotto et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Recent developments in stainless steels
K. H. Lo et al.
MATERIALS SCIENCE & ENGINEERING R-REPORTS (2009)