☆ 4.5 Article

Effects of Variated Final Temperature and Workpiece Thickness for Hot Rolling of Aluminum Alloy EN AW-8011

METALS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Mechanical

Estimating the real contact area in lubricated hot rolling of aluminium

Andre Rudnytskyj et al.

Summary: This study develops a model for estimating the real contact area in hot rolling of a 6061 aluminium alloy based on material properties, roll topography, and lubricant behavior. The results show the interplay between load and contact area, with solid contact and lubricant entrapment playing major roles, influenced by the topography and flow stress of the workpiece.

TRIBOLOGY INTERNATIONAL (2023)

添加到收藏夹

Article Mechanics

On fracture anisotropy in textured aluminium alloys

Bjorn Hakon Frodal et al.

Summary: This study investigates the fracture anisotropy of two extruded aluminium alloys with different microstructures. By comparing finite element simulations with experimental tests, the important role of crystallographic texture in plastic anisotropy is highlighted.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2022)

添加到收藏夹

Article Engineering, Industrial

Pore closure in thick aluminum plate: From industrial hot rolling to individual pore observation

P. Gravier et al.

Summary: This study investigates the volume evolution of pores during the rolling process of thick plates using X-ray microtomography. Multi-scale finite element simulations are used to replicate the loading conditions, and tomography on a synchrotron X-ray beamline is employed for characterization. The results show that the volume evolution of pores is closely related to the hydrostatic integration, confirming the enhanced closure effect of complex casting pores with high relative reduction and high L/H ratio during rolling.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Recrystallization and grain growth behavior of variously deformed CoCrFeMnNi high-entropy alloys: microstructure characterization and modeling

Chaowei Zheng et al.

Summary: The recrystallization and grain growth behavior of CoCrFeMnNi high-entropy alloys (HEAs) under different plastic deformation conditions were studied. Experimental results showed that pre-deformation promoted the recrystallization rate and degree, while higher deformation resulted in smaller annealed grain size. Severe deformation and low annealing temperature were beneficial for grain refinement. Static recrystallization model and improved grain growth model were developed to predict the recrystallization fraction and annealed grain size under different deformation and annealing conditions.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Chemistry, Physical

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

Weiwei Li et al.

Summary: The study showed that increasing the rolling temperature enhances the mechanical properties of Al-Mg-Li alloys but reduces their corrosion resistance. Different rolling temperatures also alter the alloy's texture strength.

MATERIALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

INFLUENCE OF THE HOT-ROLLING TECHNIQUE FOR EN AW-8021B ALUMINIUM ALLOY ON THE MICROSTRUCTURAL PROPERTIES OF A COLD-ROLLED FOIL

Jakob Kraner et al.

Summary: The study found that hot rolling significantly affects the final microstructure and mechanical properties of aluminium products, with crucial differences between reverse hot rolling and tandem hot rolling. Crystallographic textures of hot-rolled strips were compared, showing limitations in performance due to coarse-grained and fine-grained band areas caused by reverse hot rolling.

MATERIALI IN TEHNOLOGIJE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Characteristics of dynamic softening during high temperature deformation of CoCrFeMnNi high-entropy alloy and its correlation with the evolving microstructure and micro-texture

Sumit Ghosh et al.

Summary: The study investigated the dynamic recrystallization characteristics of a CoCrFeMnNi high-entropy alloy through hot compression testing, revealing the discontinuous DRX mechanism and establishing a new kinetic model to predict DRX recrystallization. Results showed an increase in volume fraction of DRX grains with increasing strain, and steady-state flow was achieved at a true strain rate of 10(-2) s(-1).

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

The Basis for Reliability-Based Mechanical Properties of Structural Aluminium Alloys

Davor Skejic et al.

Summary: The analysis provides statistical data on the main mechanical properties of structural aluminum, which is crucial for the correct implementation of the probabilistic approach in Eurocode 9. Adequate knowledge of mechanical properties and their statistical description is essential for reliable verification of design methods and structures. Data collection mainly focused on aluminum products in the European market over the past 20 years and data from the aluminum industry and research community over the past 30 years.

APPLIED SCIENCES-BASEL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

METALLOGRAPHIC METHODS FOR DETERMINING THE QUALITY OF ALUMINIUM ALLOYS

Jakob Kraner et al.

Summary: Metallographic investigations are critical for research and materials' quality control, with most methods used for aluminum alloys' quality determination being non-standard and customer-specified. Interlaboratory investigations showed that the suitability and effectiveness of these methods depend on correct and easily followed instructions.

MATERIALI IN TEHNOLOGIJE (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Grain size effect on tensile deformation behaviors of pure aluminum

B. B. Wang et al.

Summary: Grain refinement is an effective method to enhance the mechanical properties of materials, with the strengthening effect of high angle grain boundaries being almost three times that of low angle grain boundaries. The study classified the Hall-Petch relationships into three stages as the grain size decreased, showing a positive deviation in fine grain regime due to the increased specific surface area of HAGBs. Additionally, the positive deviation in ultrafine grained regime was influenced by an extra dislocation source limited strengthening mechanism up to 29 MPa.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Hot Band on Texture Evolution and Plastic Anisotropy in Aluminium Alloys

Jurij J. Sidor

Summary: This study reveals that the hot band texture plays a significant role in the crystallographic properties of Al alloys during thermomechanical processing, with the strength of the pre-rolling texture also impacting the final product's anisotropy.

METALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and Texture Evolution with Relation to Mechanical Properties of Compared Symmetrically and Asymmetrically Cold Rolled Aluminum Alloy

Jakob Kraner et al.

METALS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Constitutive modelling of the 6061 aluminium alloy under hot rolling conditions and large strain ranges

Andre Rudnytskyj et al.

MATERIALS & DESIGN (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

ASYMMETRIC COLD ROLLING OF AN AA 5xxx ALUMINIUM ALLOY

Jakob Kraner et al.

MATERIALI IN TEHNOLOGIJE (2020)

添加到收藏夹

Review Materials Science, Multidisciplinary

A REVIEW OF ASYMMETRIC ROLLING

Jakob Kraner et al.

MATERIALI IN TEHNOLOGIJE (2020)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Hot Rolling of a Non-heat Treatable Aluminum Alloy: Thermo-Mechanical and Microstructure Evolution Model

A. B. Nellippallil et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2017)

添加到收藏夹

Article Chemistry, Physical

Evolution of the Brass texture in an Al-Cu-Mg alloy during hot rolling

Qi Zhao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation

Lixin Zhang et al.

MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

The room temperature mechanical properties of hot rolled 7075 aluminum alloy

A. Abolhasani et al.

MATERIALS & DESIGN (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Plastic deformation and creep damage evaluations of type 316 austenitic stainless steels by EBSD

Rika Yoda et al.

MATERIALS CHARACTERIZATION (2010)

添加到收藏夹

Article Engineering, Industrial

Prediction of influence parameters on the hot rolling process using finite element method and neural network

A. R. Shahani et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effects of texture on formability of aluminum alloy sheets

Kengo Yoshida et al.

ACTA MATERIALIA (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

Simulation of casting, homogenization, and hot rolling: consecutive process and microstructure modelling for aluminium sheet production

L Neumann et al.

MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.