☆ 4.6 Article

In-doping collaboratively controlling back interface and bulk defects to achieve efficient flexible CZTSSe solar cells

JOURNAL OF ENERGY CHEMISTRY (2024)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Chemistry, Physical

Efficient Cd-Free Flexible CZTSSe Solar Cells with Quality Interfaces by Using the Zn1-XSnXO Buffer Layer br

Beibei Lin et al.

Summary: The severe carrier recombination and high toxicity of Cd at the CZTSSe/CdS heterojunction interface limit the development of flexible CZTSSe solar cells. In this study, a suitable and environmentally friendly Zn1-xSnxO (ZTO) buffer layer is used to suppress the interface recombination in the flexible solar cell for the first time. The solar cell achieves an efficiency of 8.7%, the highest reported for a Cd-free flexible CZTSSe solar cell, indicating significantly improved interface quality and reduced interfacial recombination in the ZTO devices.

ACS APPLIED ENERGY MATERIALS (2023)

添加到收藏夹

Article Chemistry, Physical

Efficient Environmentally Friendly Flexible CZTSSe/ZnO Solar Cells by Optimizing ZnO Buffer Layers

Quanzhen Sun et al.

Summary: Flexible CZTSSe solar cells, which have abundant earth elements, high stability, and wide application prospects, have gained significant attention. However, the high toxicity of the Cd in the buffer layers poses environmental problems. In this study, a Cd-free flexible CZTSSe/ZnO solar cell was developed, and the influence of ZnO films on device performances was investigated. The removal of the CdS layer enhanced the light absorption capacity of flexible CZTSSe solar cells. The optimized thickness of the ZnO buffer layers and the appropriate annealing temperature of the CZTSSe/ZnO were found to be 100 nm and 200 C-?. Ultimately, the optimized device achieved an efficiency of 5.0%, which is the highest for flexible CZTSSe/ZnO solar cells. Systematic characterizations showed that the optimized flexible CZTSSe/ZnO solar cells exhibited quality heterojunction, low defect density, and better charge transfer capability. This work provides a new strategy for the development of environmentally friendly and low-cost flexible CZTSSe solar cells.

MATERIALS (2023)

添加到收藏夹

Article Chemistry, Multidisciplinary

10.24% Efficiency of Flexible Cu2ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

Weihao Xie et al.

Summary: In this study, the authors developed a selenization technique to improve the quality of the CZTSSe layer in flexible solar cells. By pre-evaporation selenization, they were able to promote crystallization and reduce defects in the CZTSSe absorber, resulting in higher conversion efficiency. This safe and efficient method could offer a new strategy for high-efficiency flexible CZTSSe solar cells.

SMALL (2022)

添加到收藏夹

Article Chemistry, Applied

Over 12% efficient kesterite solar cell via back interface engineering

Yunhai Zhao et al.

Summary: The introduction of a WO3 intermediate layer at the back interface effectively inhibits the unfavorable interface reaction and improves the performance of CZTSSe solar cells, leading to a higher conversion efficiency.

JOURNAL OF ENERGY CHEMISTRY (2022)

添加到收藏夹

Article Chemistry, Applied

Enhancing carrier transport in flexible CZTSSe solar cells via doping Li strategy

Qiong Yan et al.

Summary: In this study, Li doping is investigated to passivate defects and reduce band tailings in CZTSSe thin-film solar cells. The results show that Li doping effectively enhances carrier transport, reduces non-radiative recombination centers, and improves the CZTSSe/CdS junction quality, leading to an increase in solar cell efficiency.

JOURNAL OF ENERGY CHEMISTRY (2022)

添加到收藏夹

Article Energy & Fuels

9.3% Efficient Flexible Cu2ZnSn(S,Se)4 Solar Cells with High-Quality Interfaces via Ultrathin CdS and Zn0.8Sn0.2O Buffer Layers

Beibei Lin et al.

Summary: This study proposes the engineering of ultra-thin CdS and ZTO buffer layers to improve the efficiency and performance of high-performance flexible CZTSSe solar cells. The ultra-thin CdS layer acts as an interface passivation layer, while the ZTO layer is used to enhance carrier collection capacity. The results show that the ultra-thin CdS and ZTO-based solar cells achieve high-quality interface and band matching.

ENERGY TECHNOLOGY (2022)

添加到收藏夹

Article Energy & Fuels

Elemental de-mixing-induced epitaxial kesterite/CdS interface enabling 13%-efficiency kesterite solar cells

Yuancai Gong et al.

Summary: The efficiency of kesterite solar cells has been stuck at 12.6% since 2013 due to challenges in controlling defects. Now Gong et al. present a low-temperature annealing of the kesterite/CdS junction to form an epitaxial interface with a low defect density, enabling 13%-efficiency devices.

NATURE ENERGY (2022)

添加到收藏夹

Article Nanoscience & Nanotechnology

Back Shallow Ge Gradient Enhanced Carrier Separation for CZTSe Solar Cells through a Coselenization Process

Jingling Liu et al.

Summary: Researchers demonstrated a CZTSe solar cell with a shallow Ge gradient, achieving an efficiency of over 10%. By using a GeSe2-Se coselenization process, they improved band tailing, junction quality, and carrier separation in the device, marking a significant breakthrough for Ge-graded CZTSe solar cells and offering a promising approach for developing Ge-involved solar cells.

ACS APPLIED MATERIALS & INTERFACES (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

Ag Incorporation with Controlled Grain Growth Enables 12.5% Efficient Kesterite Solar Cell with Open Circuit Voltage Reached 64.2% Shockley-Queisser Limit

Yuancai Gong et al.

Summary: By incorporating Ag into kesterite through a DMSO solution, this study successfully promoted grain growth, resulting in a uniform and less defective absorber.

ADVANCED FUNCTIONAL MATERIALS (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

Sodium Effects on the Diffusion, Phase, and Defect Characteristics of Kesterite Solar Cells and Flexible Cu2ZnSn(S,Se)4 with Greater than 11% Efficiency

Kee-Jeong Yang et al.

Summary: This study investigates the effects of Na doping on the efficiency of kesterite solar cells by applying a NaF layer at different positions within precursors. The NaF layer limits Zn diffusion, suppresses Cu-Zn alloy formation, and provides reactive Se and S to the absorber layer, reducing the impact of Na and improving efficiency. By applying NaF between the Zn layer and back contact and between the Cu and Sn layers, efficiency values of 11.16% and 11.19% are achieved for flexible CZTSSe solar cells.

ADVANCED FUNCTIONAL MATERIALS (2021)

添加到收藏夹

Article Chemistry, Physical

Efficiency Improvement of Flexible Cu2ZnSn(S,Se)4 Solar Cells by Window Layer Interface Engineering

Quanzhen Sun et al.

Summary: By utilizing a modified window layer structure (S/CdS/ITO), the performance of flexible CZTSSe solar cells has been enhanced, achieving an efficiency of 9.2%. The introduction of MgF2 antireflection coatings leads to a 6% improvement in the average J(sc) of the devices, with a champion device reaching an efficiency of 9.7%.

ACS APPLIED ENERGY MATERIALS (2021)

添加到收藏夹

Article Energy & Fuels

Li plus &Ag plus and Li+&Cd2+double-ion-doping strategy to improve the efficiency of Cu2ZnSn(S,Se)4 solar cells

Junye Tong et al.

Summary: This study successfully improved the microstructure and device performance of CZTSSe solar cells by employing Li+&Ag+ and Li+&Cd2+ double-ion-doping strategy, achieving significant efficiency enhancements.

SOLAR ENERGY (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Insights into High-Efficiency Ag-Alloyed CZTSSe Solar Cells Fabricated through Aqueous Spray Deposition

Temujin Enkhbat et al.

Summary: Kesterite Cu2ZnSnSe4 (CZTSe), Cu2ZnSn(S,Se)(4) (CZTSSe), and Cu2ZnSnS4 (CZTS) solar cells exhibit lower open-circuit voltages than their theoretical values, hindering efficiency improvement and mass production. By substituting Ag into CZTSSe, the Cu/Zn disorder can be reduced, leading to enhanced performance in solar cells.

ACS APPLIED MATERIALS & INTERFACES (2021)

添加到收藏夹

Article Chemistry, Physical

Numerical Study to Improve the Back Interface Contact of CZTSSe Solar Cells Using Oxygen-Doped Mo(Se1-x, Ox)2

Caixia Zhang et al.

Summary: The study shows that oxygen-doped molybdenum selenide can effectively optimize the back interface contact of CZTSSe solar cells and improve the energy conversion efficiency.

JOURNAL OF PHYSICAL CHEMISTRY C (2021)

添加到收藏夹

Article Chemistry, Physical

Fabrication of high-efficiency Cu2(Zn,Cd)SnS4 solar cells by a rubidium fluoride assisted co-evaporation/annealing method

Shijin Wang et al.

Summary: The study successfully enhanced the quality of CCZTS thin films and solar devices through Rb incorporation, leading to improvements in bulk and interface properties and carrier collection efficiency enhancement, achieving a champion efficiency of 10.64%.

JOURNAL OF MATERIALS CHEMISTRY A (2021)

添加到收藏夹

Article Chemistry, Physical

Enhancing Ag-alloyed Cu2ZnSnS4 solar cell performance by interfacial modification via In and Al

Ping Fan et al.

Summary: The study demonstrates that doping with In or Al at the interface of Ag-alloyed CZTS thin film solar cells can enhance device performance, resulting in over 11% efficiency. Additionally, replacing indium tin oxide (ITO) with low-cost Al-doped ZnO (AZO) as the front electrode can achieve over 10% efficiency in CZTS devices without In.

JOURNAL OF MATERIALS CHEMISTRY A (2021)

添加到收藏夹

Article Engineering, Environmental

An effective combination reaction involved with sputtered and selenized Sb precursors for efficient Sb2Se3 thin film solar cells

Yan-Di Luo et al.

CHEMICAL ENGINEERING JOURNAL (2020)

添加到收藏夹

Article Chemistry, Multidisciplinary

Device Postannealing Enabling over 12% Efficient Solution-Processed Cu2ZnSnS4Solar Cells with Cd2+Substitution

Zhenghua Su et al.

ADVANCED MATERIALS (2020)

添加到收藏夹

Article Energy & Fuels

Beyond 10% efficient Cu2ZnSn(S,Se)4 solar cells: Effects of the introduction of SnS powder during selenization process

Bin Xu et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2020)

添加到收藏夹

Article Chemistry, Physical

Eliminating multi-layer crystallization of Cu2ZnSn(S,Se)4 absorber by controlling back interface reaction

Qing Yu et al.

NANO ENERGY (2020)

添加到收藏夹

Article Chemistry, Physical

Engineering the Band Offsets at the Back Contact Interface for Efficient Kesterite CZTSSe Solar Cells

Afei Zhang et al.

ACS APPLIED ENERGY MATERIALS (2020)

添加到收藏夹

Article Chemistry, Physical

Ag, Ge dual-gradient substitution for low-energy loss and high-efficiency kesterite solar cells

Junjie Fu et al.

JOURNAL OF MATERIALS CHEMISTRY A (2020)

添加到收藏夹

Article Chemistry, Multidisciplinary

Defect Control for 12.5% Efficiency Cu2ZnSnSe4 Kesterite Thin-Film Solar Cells by Engineering of Local Chemical Environment

Jianjun Li et al.

ADVANCED MATERIALS (2020)

添加到收藏夹

Article Chemistry, Applied

Lithium-assisted synergistic engineering of charge transport both in GBs and GI for Ag-substituted Cu2ZnSn(S,Se)4 solar cells

Xiangyun Zhao et al.

JOURNAL OF ENERGY CHEMISTRY (2020)

添加到收藏夹

Article Energy & Fuels

Mechanism of Current Shunting in Flexible Cu2Zn1-xCdxSn(S,Se)4 Solar Cells

Qiong Yan et al.

SOLAR RRL (2020)

添加到收藏夹

Review Chemistry, Physical

Advanced Alkali Treatments for High-Efficiency Cu(In,Ga)Se2 Solar Cells on Flexible Substrates

Romain Carron et al.

ADVANCED ENERGY MATERIALS (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

8% Efficiency Cu2ZnSn(S,Se)4 (CZTSSe) Thin Film Solar Cells on Flexible and Lightweight Molybdenum Foil Substrates

Eunae Jo et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Interfacial engineering to improve Cu2ZnSnX4 (X = S, Se) solar cell efficiency

H. J. Gu et al.

APL MATERIALS (2019)

添加到收藏夹

Article Energy & Fuels

High flexible Cu2ZnSn(S,Se)4 solar cells by green solution-process

Qiong Yan et al.

SOLAR ENERGY (2019)

添加到收藏夹

Article Energy & Fuels

Chemical Dynamics of Back Contact with MoO3 Interfacial Layer in Kesterite Solar Cells: Microstructure Evolution and Photovoltaic Performance

Afei Zhang et al.

SOLAR RRL (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Achieving 14.4% Alcohol-Based Solution-Processed Cu(In,Ga)(S,Se)(2) Thin Film Solar Cell through Interface Engineering

Gi Soon Park et al.

ACS APPLIED MATERIALS & INTERFACES (2018)

添加到收藏夹

Article Chemistry, Physical

Behavior of indium alloying with Cu2ZnSn(S,Se)4 and its effect on performances of Cu2ZnSn(S,Se)4-based solar cell

Zhenyu Xiao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

添加到收藏夹

Article Physics, Condensed Matter

Modification of back electrode with WO3 layer and its effect on Cu2ZnSn(S,Se)4-based solar cells

Kun Shi et al.

SUPERLATTICES AND MICROSTRUCTURES (2018)

添加到收藏夹

Article Chemistry, Multidisciplinary

Synthesis of simple, low cost and benign sol-gel Cu2InxZn1-xSnS4 alloy thin films: influence of different rapid thermal annealing conditions and their photovoltaic solar cells

Yingrui Sui et al.

RSC ADVANCES (2018)

添加到收藏夹

Review Chemistry, Multidisciplinary

Cation Substitution in Earth-Abundant Kesterite Photovoltaic Materials

Jianjun Li et al.

ADVANCED SCIENCE (2018)

添加到收藏夹

Article Chemistry, Multidisciplinary

Efficient (Cu1-xAgx)2ZnSn(S,Se)4 solar cells on flexible Mo foils

Xue Yu et al.

RSC ADVANCES (2018)

添加到收藏夹

Article Chemistry, Multidisciplinary

Engineering of interface band bending and defects elimination via a Ag-graded active layer for efficient (Cu,Ag)2ZnSn(S,Se)4 solar cells

Ya-Fang Qi et al.

ENERGY & ENVIRONMENTAL SCIENCE (2017)

添加到收藏夹

Article Energy & Fuels

Precise-tuning the In content to achieve high fill factor in hybrid buffer structured Cu2ZnSn(S, Se)4 solar cells

Yingli Pei et al.

SOLAR ENERGY (2017)

添加到收藏夹

Article Chemistry, Physical

Fill Factor Losses in Cu2ZnSn(SxSe1-x)4 Solar Cells: Insights from Physical and Electrical Characterization of Devices and Exfoliated Films

Kong Fai Tai et al.

ADVANCED ENERGY MATERIALS (2016)

添加到收藏夹

Article Energy & Fuels

High efficiency CZTSSe thin film solar cells from pure element solution: A study of additional Sn complement

Jing Guo et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2016)

添加到收藏夹

Article Energy & Fuels

Optical and electrical properties of In-doped Cu2ZnSnSe4

S. Giraldo et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2016)

添加到收藏夹

Article Chemistry, Multidisciplinary

Engineering Solar Cell Absorbers by Exploring the Band Alignment and Defect Disparity: The Case of Cu- and Ag-Based Kesterite Compounds

Zhen-Kun Yuan et al.

ADVANCED FUNCTIONAL MATERIALS (2015)

添加到收藏夹

Article Chemistry, Multidisciplinary

High Efficiency Cu2ZnSn(S,Se)4 Solar Cells by Applying a Double In2S3/CdS Emitter

Jeehwan Kim et al.

ADVANCED MATERIALS (2014)

添加到收藏夹

Article Chemistry, Multidisciplinary

A Detrimental Reaction at the Molybdenum Back Contact in Cu2ZnSn(S,Se)4 Thin-Film Solar Cells

Jonathan J. Scragg et al.

JOURNAL OF THE AMERICAN CHEMICAL SOCIETY (2012)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.