☆ 4.6 Article

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy

MATERIALS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Mechanism of room-temperature superplasticity in ultrafine-grained Al-Zn alloys

Zizheng Song et al.

Summary: Superplastic deformation of polycrystalline materials is usually achieved by diffusion-assisted grain boundary sliding at high temperatures. Recent research has shown that room-temperature superplasticity can be achieved in ultrafine-grained Al-Zn based alloys, but the underlying mechanism is still unclear. This study utilized in-situ tensile straining, electron microscopy characterization, and atomistic density functional theory simulation to reveal that the superplasticity at room temperature is achieved by grain boundary sliding and grain rotation, facilitated by the continuous diffusion of Zn. The diffusion of Zn atoms from grains to grain boundaries forms a Zn nanolayer, acting as a solid lubricant to lower the energy barrier of grain boundary sliding.

ACTA MATERIALIA (2023)

添加到收藏夹

Article Chemistry, Physical

Enhanced intragranular dislocation capture ability in nano/ultrafine Al- Zn-Mg-Cu alloy by burnishing-assisted two-stage aging treatment- induced dynamic nucleation

Tianshu Zhao et al.

Summary: The effects of burnishing-assisted two-stage aging (BATSA) on the microstructural evolution and hardening behavior of Al-Zn-Mg-Cu alloy were investigated. The BATSA treatment promoted a concentrated distribution of precipitate sizes and delayed phase coalescence. Moreover, dynamic nucleation induced by pre-aging and burnishing resulted in a better synergy of multiple strengthening mechanisms, significantly shortening the time to peak hardness in pre-aged burnished alloys.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of Zn content on microstructure evolution in Al-Zn alloys processed by high-pressure torsion

Anwar Q. Ahmed et al.

Summary: Al-Zn alloys with different Zn contents were processed by HPT to produce UFG materials. Microstructural features of the UFG Al-Zn alloys were studied using various techniques. The mechanical behavior of the alloys showed a substantial difference with increasing Zn content, and the microstructure evolved differently in low and high Zn-containing alloys during the HPT process.

JOURNAL OF MATERIALS RESEARCH (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of intermediate-temperature severe plastic deformation on microstructure evolution, mechanical properties and corrosion behavior of an Al-Zn-Mg-Cu alloy

Guisheng Li et al.

Summary: In this study, the Al-Zn-Mg-Cu alloy was processed by intermediate-temperature equal channel angular pressing (ECAP) to achieve grain refinement and improve its mechanical properties and corrosion resistance.

MATERIALS CHARACTERIZATION (2023)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effect of thermal strain on the microstructure evolution and post-aging mechanical properties of Al-Zn-Mg-Cu alloy in simulating hot stamping process

Jue Lu et al.

Summary: This study investigates the effect of thermal strain on the microstructure evolution and mechanical properties of Al-Zn-MgCu alloys. The alloys undergo elevated temperature strain and artificial aging at 120 degrees C for various periods of time. The post-aging mechanical properties of the alloys are examined, and the microstructures are characterized using various techniques. The results show that thermal strain leads to an increase in ultimate tensile stress, a decrease in peak-aging time, and a slight refinement of deformed grains.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Overview: Using Severe Plastic Deformation in the Processing of Superplastic Materials

Terence G. Langdon

Summary: In tensile testing, polycrystalline materials usually fail at low total elongations, but under certain conditions, exceptionally high elongations of over 400% can be achieved. This superplastic condition is not only important scientifically, but also has significant industrial applications in superplastic forming operations. This overview traces the historical development of the superplastic effect and summarizes the main characteristics of the superplastic flow process. Severe plastic deformation (SPD) processing has effectively overcome the limitation of producing exceptionally small grain sizes within the submicrometer or nanometer range. The advantages of SPD processing are discussed and illustrated with examples. Additionally, the construction of deformation mechanism maps based on stress, grain size, and temperature combinations is shown as an effective way to display experimental data.

MATERIALS TRANSACTIONS (2023)

添加到收藏夹

Review Materials Science, Multidisciplinary

Effects of equal channel angular pressing and further cold upsetting process to the kinetics of precipitation during aging of 7050 aluminum alloy

Dong-sheng Jia et al.

Summary: The effects of equal channel angular pressing (ECAP) and further cold upsetting (CU) process on the precipitation kinetics during aging of solid solution treated 7050 Al alloy were investigated. It was found that the activation energy of the h' phase decreased after ECAP and ECAP-CU processes, resulting in a shorter peak aging time. The precipitation of the h phase was suppressed after ECAP, while it was accelerated after ECAP-CU process. The competition between dislocation annihilation and phase precipitation during aging treatment led to the softening and strengthening of the mechanical strength. The elongation increased while the strength slightly decreased.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Computational analysis of heterogeneous nucleation and precipitation in AA6005 Al-alloy during continuous cooling DSC experiments

Bernhard Miesenberger et al.

Summary: A physically-based model for the computational evaluation of DSC curves during continuous cooling of Al alloys has been developed. The model predicts the nucleation and growth of quench-induced precipitates at heterogeneous nucleation sites. The model considers the effects of interface curvature and diffuse interfaces for interface energy prediction. Experiment and simulation comparisons show that the impact of heterogeneous nucleation sites must be adequately considered for accurate predictions of precipitate evolution during continuous cooling.

MATERIALIA (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Low temperature super ductility and threshold stress of an ultrafine-grained Al-Zn-Mg-Zr alloy processed by equal-channel angular pressing

Balint Boldizsar et al.

Summary: The study found that the ultrafine-grained alloy exhibited super ductility in the low temperature range, with relatively high strain rate sensitivity and low activation energy.

JOURNAL OF MATERIALS SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ultralow-temperature superplasticity and its novel mechanism in ultrafine-grained Al alloys

Nguyen Q. Chinh et al.

Summary: This study discovered ultralow-temperature superplasticity in commercial 7xxx Al alloy for the first time, providing a foundation for the development of new technologies to manufacture complex-shaped metallic parts with enhanced service properties.

MATERIALS RESEARCH LETTERS (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Influence of aging on microstructure, mechanical properties and stress corrosion cracking of 7136 aluminum alloy

Wei Shi-long et al.

Summary: The study found that the 7136 aluminum alloy after T6 aging has higher tensile and yield strength, the fracture toughness is significantly improved in the T74 aging alloy, and the T79 aging alloy has better resistance to stress corrosion cracking.

JOURNAL OF CENTRAL SOUTH UNIVERSITY (2021)

添加到收藏夹

Article Chemistry, Physical

Synchrotron-based holotomography and X-ray fluorescence study on the stress corrosion cracking behavior of the peak-aged 7075 aluminum alloy

Christoph Altenbach et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

3D Time-Resolved Observations of Fatigue Crack Initiation and Growth from Corrosion Pits in Al 7XXX Alloys Using In Situ Synchrotron X-ray Tomography

Arun Sundar Sundaram Singaravelu et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

添加到收藏夹

Article Multidisciplinary Sciences

Precipitation strengthening of aluminum alloys by room-temperature cyclic plasticity

Wenwen Sun et al.

SCIENCE (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

The influence of artificial aging on the microstructure and hardness of an Al-Zn-Mg-Zr alloy processed by equal-channel angular pressing

Jeno Gubicza et al.

JOURNAL OF MATERIALS SCIENCE (2019)

添加到收藏夹

Article Thermodynamics

DSC analysis of phase transformations during precipitation hardening in Al-Zn-Mg alloy (7020)

M. Chemingui et al.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Low-Temperature and High-Strain-Rate Superplasticity of Ultrafine-Grained A7075 Processed by High-Pressure Torsion

Seungwon Lee et al.

MATERIALS TRANSACTIONS (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Effects of aging on mechanical properties and microstructure of multi-directionally forged 7075 aluminum alloy

Tomoya Aoba et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Review: Overcoming the paradox of strength and ductility in ultrafine-grained materials at low temperatures

Praveen Kumar et al.

JOURNAL OF MATERIALS SCIENCE (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Coupling of dislocations and precipitates: Impact on the mechanical behavior of ultrafine grained Al-Zn-Mg alloys

Kaka Ma et al.

ACTA MATERIALIA (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Simultaneous improvements of the strength and ductility of fine-grained AA6063 alloy with increasing number of ECAP passes

M. Samaee et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Strengthening of AA7075 alloy by processing with high-pressure sliding (HPS) and subsequent aging

Seungwon Lee et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

添加到收藏夹

Article Chemistry, Physical

Dissolution and Precipitation Behaviour during Continuous Heating of Al-Mg-Si Alloys in a Wide Range of Heating Rates

Julia Osten et al.

MATERIALS (2015)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

TEM OBSERVATION OF PRECIPITATE STRUCTURES IN Al-Zn-Mg ALLOYS WITH ADDITIONS OF Cu/Ag

K. Watanabe et al.

ARCHIVES OF METALLURGY AND MATERIALS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

The grain refinement mechanism of cast aluminium by zirconium

Feng Wang et al.

ACTA MATERIALIA (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Aluminium in Innovative Light-Weight Car Design

Juergen Hirsch

MATERIALS TRANSACTIONS (2011)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Determination of kinetic parameters from calorimetric study of solid state reactions in 7150 Al-Zn-Mg alloy

K. S. Ghosh et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

Developing Processing Routes for the Equal-Channel Angular Pressing of Age-Hardenable Aluminum Alloys

Zhi Chao Duan et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2010)

添加到收藏夹

Article Thermodynamics

DSC analysis of the precipitation reaction in AA6005 alloy

Y. Birol

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Asymmetric tilt grain boundary structure and energy in copper and aluminium

M. A. Tschopp et al.

PHILOSOPHICAL MAGAZINE (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of ECAP on precipitate distributions in a spray-east aluminum alloy

C Xu et al.

ACTA MATERIALIA (2005)

添加到收藏夹

Article Nanoscience & Nanotechnology

Hall-Petch relation and boundary strengthening

N Hansen

SCRIPTA MATERIALIA (2004)

添加到收藏夹

Article Chemistry, Physical

The effect of Cu on mechanical and precipitation properties of AI-Zn-Mg alloys

NQ Chinh et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2004)

添加到收藏夹

Article Nanoscience & Nanotechnology

Recent development in aluminium alloys for the automotive industry

WS Miller et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)

添加到收藏夹

Article Nanoscience & Nanotechnology

Recent development in aluminium alloys for aerospace applications

A Heinz et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)

添加到收藏夹

Article Materials Science, Multidisciplinary

Differential scanning calorimetry and electron diffraction investigation on low-temperature aging in Al-Zn-Mg alloys

XJ Jiang et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.