☆ 4.8 Article

Cathode Interface Construction by Rapid Sintering in Solid-State Batteries

SMALL (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Review Chemistry, Multidisciplinary

Priority and Prospect of Sulfide-Based Solid-Electrolyte Membrane

Hong Liu et al.

Summary: This review focuses on the importance of thin membrane-based separators for mass production of all-solid-state lithium batteries (ASSLBs) using sulfide solid electrolytes (SEs). The critical criteria for high-quality sulfide SE membranes are discussed, along with the major challenges and strategies in material availability, membrane processing, and cell integration. Future directions and prospects for scalable and manufacturable sulfide SE membranes in ASSLBs are also presented.

ADVANCED MATERIALS (2023)

添加到收藏夹

Article Electrochemistry

A Li3PO4 coating strategy to enhance the Li-ion transport properties of Li2ZnTi3O8 anode material for Lithium-ion Battery

Xiaotong Liu et al.

Summary: Li2ZnTi3O8 (LZTO) has been studied as a potential anode material for rechargeable lithium-ion batteries, however, its high-rate capacity is limited due to slow Li-ion diffusion kinetics and side reactions at the electrode/electrolyte interface. This study investigates the use of Li3PO4 as a lithium ion conductor and modifier to improve the crystal structure and electrochemical properties of LZTO. The Li3PO4-coated LZTO electrode shows enhanced electrochemical performance with high capacity retention, low electrode polarization, and good cycling stability at high temperatures.

ELECTROCHIMICA ACTA (2023)

添加到收藏夹

Article Chemistry, Physical

Lithium Argyrodite Sulfide Electrolytes with High Ionic Conductivity and Air Stability for All-Solid-State Li-Ion Batteries

Yongheum Lee et al.

Summary: Solid electrolytes, such as lithium thioantimonate iodide argyrodites, show high ionic conductivities and air-stability, making them promising materials for enhancing the performance of all-solid-state batteries. Ge-substituted thioantimonate argyrodites achieved high ionic conductivity and compatibility with catholytes, showing potential for cost-effective and stable all-solid-state batteries. The superionic conductors with high air-stability reported in this study demonstrate substantial promise for the development of all-solid-state batteries.

ACS ENERGY LETTERS (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

Active Interphase Enables Stable Performance for an All-Phosphate-Based Composite Cathode in an All-Solid-State Battery

Qi Xu et al.

Summary: This work demonstrates a simple but effective strategy to stabilize the cathode active material/solid-state electrolyte interface in high mass loading all-solid-state batteries (ASSBs). The obtained composite cathode shows stable operation and high reversible capacity due to the activated LFTAP interphase and LATP electrolyte.

SMALL (2022)

添加到收藏夹

Article Multidisciplinary Sciences

Promoting favorable interfacial properties in lithium-based batteries using chlorine-rich sulfide inorganic solid-state electrolytes

Dewu Zeng et al.

Summary: The interfacial stability of lithium metal is crucial for the development of all-solid-state batteries. In this study, researchers investigate the influence of chloride distribution and cooling process on the evolution of the Li|SE interface microstructure. They found that controlling these factors can lead to the formation of a LiCl-rich interphase layer, which improves battery cycling performance.

NATURE COMMUNICATIONS (2022)

添加到收藏夹

Article Chemistry, Physical

PI-LATP-PEO Electrolyte with High Safety Performance in Solid-State Lithium Metal Batteries

Lei He et al.

Summary: This study proposes a solution to the safety issues in lithium metal batteries by using a solid-state electrolyte. By compounding a nanofiber membrane with polymers and inorganic salt, the electrochemical and battery performance of the batteries were significantly improved.

ACS APPLIED ENERGY MATERIALS (2022)

添加到收藏夹

Article Chemistry, Physical

Advanced Analytical Characterization of Interface Degradation in Ni-Rich NCM Cathode Co-Sintered with LATP Solid Electrolyte

Michael Malaki et al.

Summary: This study investigates the morphological, structural, and chemical changes that occur between commercial NCM622 cathode and oxide SE LATP at different temperatures during cosintering process. The degradation process of NCM particles in the composites is observed using high-resolution microscopy, and further analysis is conducted using ACOM-TEM and ToF-SIMS techniques. The results show a close correlation between the phase transitions of NCM particles and the temperature-dependent lithium transfer.

ACS APPLIED ENERGY MATERIALS (2022)

添加到收藏夹

Article Materials Science, Ceramics

Li3PO4 electrolyte of high conductivity for all-solid-state lithium battery prepared by plasma spray

Yin-Qiu Sun et al.

Summary: Li3PO4 (LPO) deposits were prepared using atmospheric plasma-spraying (APS) with varying sizes of sintered powders, which affected the microstructure and ion conductivity of the deposits. Smaller feedstock particle sizes resulted in decreased porosity of the deposits, and using particles smaller than 30 µm achieved a high room-temperature ionic conductivity of 4.65 x 10(-8) S.cm(-1) in the APS LPO deposit.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

添加到收藏夹

Article Multidisciplinary Sciences

High-surface-area corundum nanoparticles by resistive hotspot-induced phase transformation

Bing Deng et al.

Summary: In this study, dehydrated alpha-Al2O3 nanoparticles were synthesized by pulsed direct current Joule heating of gamma-Al2O3. The rapid phase transformation at reduced temperature and time resulted in nanograined ceramics with superior hardness.

NATURE COMMUNICATIONS (2022)

添加到收藏夹

Review Chemistry, Physical

Garnet Solid Electrolyte for Advanced All-Solid-State Li Batteries

Laiqiang Xu et al.

Summary: This article discusses the importance of all-solid-state lithium batteries in the field of energy storage, explores the challenges faced by garnet-type solid electrolytes, and proposes prospective developments and alternative approaches to solving the issues of solid-state electrolytes.

ADVANCED ENERGY MATERIALS (2021)

添加到收藏夹

Review Chemistry, Multidisciplinary

Interface Issues and Challenges in All-Solid-State Batteries: Lithium, Sodium, and Beyond

Shuaifeng Lou et al.

Summary: This article discusses the interface principles and engineering in all-solid-state batteries, emphasizing the importance of interface physics and chemistry in battery performance, and proposing strategies to address technical challenges.

ADVANCED MATERIALS (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Reaction of Li1.3Al0.3Ti1.7(PO4)3 and LiNi0.6Co0.2Mn0.2O2 in Co-Sintered Composite Cathodes for Solid-State Batteries

Jean Philippe Beaupain et al.

Summary: The study investigates the reaction between the solid electrolyte Li1.3Al0.3Ti1.7(PO4)(3) (LATP) and the active material LiNi0.6Co0.2Mn0.2O2 (NCM622) in all-ceramic oxide batteries through cosintering, which reveals that elemental diffusion and decomposition reactions occur even at low sintering temperatures, hindering the densification of the composite and the formation of ion-conducting paths between individual particles. Based on the experimental results, a mechanism of the reactions in cosintered LATP and NCM622 oxide composite cathodes is suggested.

ACS APPLIED MATERIALS & INTERFACES (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

Amorphous Dual-Layer Coating: Enabling High Li-Ion Conductivity of Non-Sintered Garnet-Type Solid Electrolyte

Yuan Gao et al.

Summary: A novel strategy to achieve high Li+ ion conductivity of Garnet-type oxide Li6.4La3Zr1.4Ta0.6O12(LLZTO) without sintering is demonstrated by ball milling LLZTO together with LiBH4 to form a composite electrolyte with unique amorphous dual coating. The composite electrolyte displays an ultra-high Li+ transference number and enables long-term cycling of symmetric Li-Li cells.

ADVANCED FUNCTIONAL MATERIALS (2021)

添加到收藏夹

Review Energy & Fuels

Processing thin but robust electrolytes for solid-state batteries

Moran Balaish et al.

Summary: This review critically discusses the research status of high-energy-density solid-state batteries, focusing on cost-effective processing and the integration of solid electrolyte materials. The future design of SSBs should consider capturing the thermal processing budget and stability of the oxide solid electrolyte phase.

NATURE ENERGY (2021)

添加到收藏夹

Article Multidisciplinary Sciences

A dynamic stability design strategy for lithium metal solid state batteries

Luhan Ye et al.

Summary: A multi-layered electrolyte design can inhibit the growth of lithium dendrites in solid-state lithium metal batteries, improving their performance. However, practical challenges remain in realizing a lithium metal anode for batteries.

NATURE (2021)

添加到收藏夹

Review Chemistry, Physical

Garnet-Based Solid-State Li Batteries: From Materials Design to Battery Architecture

Sara Abouali et al.

Summary: This review focuses on the garnet family as a solid electrolyte candidate, discussing its structure, optimization for ionic conductivity, and synthesis methods for different garnet solid electrolytes, as well as providing a detailed comparison of garnet-based all-solid-state lithium batteries. It aims to pave the way for practical garnet-based all-solid-state lithium batteries by providing insights into the latest achievements in the field.

ACS ENERGY LETTERS (2021)

添加到收藏夹

Review Chemistry, Physical

Energy Storage Materials for Solid-State Batteries: Design by Mechanochemistry

Roman Schlem et al.

Summary: This review discusses the physical and mechanochemical processes that influence the processing of solid-state batteries, with a focus on the influence of milling and dispersing procedures on the ionic transport properties. By combining theoretical backgrounds with a wide range of examples, a better understanding of critical parameters related to mechanical milling of solid electrolytes and solid-state battery components is provided.

ADVANCED ENERGY MATERIALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Increased Ion Conductivity in Composite Solid Electrolytes With Porous Co3O4 Cuboids

Qiongyu Zhou et al.

Summary: In this study, porous Co3O4 cuboids were introduced into PEO-based electrolyte to enhance the ionic conductivity and performance of the all-solid-state batteries. The Co3O4 fillers disrupted the order motion of polymer segments, increasing the amorphous phase amount, and built a Li+ continuous migration pathway through Lewis acid-base interaction. The composite polymer electrolyte exhibited a Li+ conductivity of 1.6 x 10(-4) S cm(-1) at 30 degrees C, showing good compatibility with Li metal anode and LiFePO4 cathode for improved rate performance and cycle life in all-solid-state LiFePO4 batteries.

FRONTIERS IN MATERIALS (2021)

添加到收藏夹

Review Green & Sustainable Science & Technology

An advance review of solid-state battery: Challenges, progress and prospects

Cong Li et al.

Summary: This review highlights the importance of solid electrolytes in lithium-ion batteries, discusses the challenges in optimizing the performance of solid electrolytes, and provides an outlook on future research directions.

SUSTAINABLE MATERIALS AND TECHNOLOGIES (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

All solid thick oxide cathodes based on low temperature sintering for high energy solid batteries

Xiang Han et al.

Summary: Solid-state batteries (SSBs) have the potential to improve safety and energy density compared to conventional liquid cells. By utilizing NASICON-type solid electrolyte Li1.3Al0.3Ti1.7(PO4)3 (LATP) and constructing mixed conductive interphases through low-melting-point liquid sintering, high-loading solid cathodes with improved kinetics have been achieved, showing promising capacity loading up to 6 mA h cm(-2) for LATP/LiCoO2 cathodes and up to 10 mAh cm(-2) for Ni-rich cathodes, leading to cells with energy density exceeding 400 Wh kg(-1).

ENERGY & ENVIRONMENTAL SCIENCE (2021)

添加到收藏夹

Review Materials Science, Multidisciplinary

Progress and perspective of Li1+ xAlxTi2-x(PO4)3 ceramic electrolyte in lithium batteries

Ke Yang et al.

Summary: LATP solid-state electrolyte shows high ionic conductivity and superior air stability, making it a promising candidate for high-energy-density lithium batteries. However, the high interfacial impedance with electrodes and side reactions with lithium metal limit its applications in all-solid-state batteries.

INFOMAT (2021)

添加到收藏夹

Review Chemistry, Multidisciplinary

All-solid-state lithium batteries enabled by sulfide electrolytes: from fundamental research to practical engineering design

Changhong Wang et al.

Summary: This review highlights the latest progress in sulfide electrolyte-based all-solid-state lithium batteries, focusing on effective strategies to improve ion conductivity and interface stability, as well as methods to address challenges at the cathode and anode interfaces. Advanced in situ characterization techniques are examined to provide a deeper understanding of the interface properties of all-solid-state lithium batteries.

ENERGY & ENVIRONMENTAL SCIENCE (2021)

添加到收藏夹

Review Chemistry, Physical

Solid-State Li-Metal Batteries: Challenges and Horizons of Oxide and Sulfide Solid Electrolytes and Their Interfaces

Kun Joong Kim et al.

Summary: The introduction of new, safe, and reliable solid-electrolyte chemistries and technologies can potentially overcome the challenges facing their liquid counterparts while widening the breadth of possible applications. Through analyzing the transition from liquid-based Li-ion batteries (LIBs) to all-solid-state Li-metal batteries (ASSLBs), a roadmap for the development of a successful oxide and sulfide-based ASSLB is introduced, focusing on interfacial challenges and considering parameters such as energy density, power density, longterm stability, processing, and safety.

ADVANCED ENERGY MATERIALS (2021)

添加到收藏夹

Review Chemistry, Multidisciplinary

Approaching Practically Accessible Solid-State Batteries: Stability Issues Related to Solid Electrolytes and Interfaces

Rusong Chen et al.

CHEMICAL REVIEWS (2020)

添加到收藏夹

Article Chemistry, Physical

Li2CO3: A Critical Issue for Developing Solid Garnet Batteries

Hanyu Huo et al.

ACS ENERGY LETTERS (2020)

添加到收藏夹

Review Nanoscience & Nanotechnology

Designing solid-state electrolytes for safe, energy-dense batteries

Qing Zhao et al.

NATURE REVIEWS MATERIALS (2020)

添加到收藏夹

Article Engineering, Environmental

Interface engineering on cathode side for solid garnet batteries

Zhijie Bi et al.

CHEMICAL ENGINEERING JOURNAL (2020)

添加到收藏夹

Review Chemistry, Multidisciplinary

Garnet-Type Solid-State Electrolytes: Materials, Interfaces, and Batteries

Chengwei Wang et al.

CHEMICAL REVIEWS (2020)

添加到收藏夹

Article Chemistry, Physical

Optimization of a Heterogeneous Ternary Li3PO4-Li3BO3-Li2SO4 Mixture for Li-Ion Conductivity by Machine Learning

Kenji Homma et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2020)

添加到收藏夹

Review Chemistry, Multidisciplinary

Interfaces and Interphases in All-Solid-State Batteries with Inorganic Solid Electrolytes

Abhik Banerjee et al.

CHEMICAL REVIEWS (2020)

添加到收藏夹

Article Chemistry, Physical

Competing Effect of Co3+ Reducibility and Oxygen-Deficient Defects Toward High Oxygen Evolution Activity in Co3O4 Systems in Alkaline Medium

Chandraraj Alex et al.

ACS APPLIED ENERGY MATERIALS (2020)

添加到收藏夹

Article Chemistry, Physical

High-Temperature Chemical Stability of Li1.4Al0.4Ti1.6(PO4)3 Solid Electrolyte with Various Cathode Materials for Solid-State Batteries

Chan-Yeop Yu et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2020)

添加到收藏夹

Review Chemistry, Physical

Structure Design of Cathode Electrodes for Solid-State Batteries: Challenges and Progress

Xu-Dong Zhang et al.

SMALL STRUCTURES (2020)

添加到收藏夹

Article Chemistry, Physical

A Long Cycle Life, All-Solid-State Lithium Battery with a Ceramic-Polymer Composite Electrolyte

Xingwen Yu et al.

ACS APPLIED ENERGY MATERIALS (2020)

添加到收藏夹

Review Chemistry, Multidisciplinary

Synthesis and Properties of NaSICON-type LATP and LAGP Solid Electrolytes

Rachel DeWees et al.

CHEMSUSCHEM (2019)

添加到收藏夹

Review Nanoscience & Nanotechnology

Interface in Solid-State Lithium Battery: Challenges, Progress, and Outlook

Syed Atif Peryez et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

添加到收藏夹

Article Chemistry, Physical

Constructing Multifunctional Interphase between Li1.4Al0.4Ti1.6(PO4)3 and Li Metal by Magnetron Sputtering for Highly Stable Solid-State Lithium Metal Batteries

Xiaoge Hao et al.

ADVANCED ENERGY MATERIALS (2019)

添加到收藏夹

Review Chemistry, Multidisciplinary

Sulfide-Based Solid-State Electrolytes: Synthesis, Stability, and Potential for All-Solid-State Batteries

Qing Zhang et al.

ADVANCED MATERIALS (2019)

添加到收藏夹

Article Chemistry, Physical

Stabilizing Solid Electrolyte-Anode Interface in Li-Metal Batteries by Boron Nitride-Based Nanocomposite Coating

Qian Cheng et al.

JOULE (2019)

添加到收藏夹

Review Chemistry, Physical

Solid Garnet Batteries

Ning Zhao et al.

JOULE (2019)

添加到收藏夹

Article Chemistry, Physical

Compatibility study of oxide and olivine cathode materials with lithium aluminum titanium phosphate

Michael Gellert et al.

IONICS (2018)

添加到收藏夹

Article Chemistry, Multidisciplinary

Robust Pinhole-free Li3N Solid Electrolyte Grown from Molten Lithium

Yanbin Li et al.

ACS CENTRAL SCIENCE (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Interface Re-Engineering of Li10GeP2S12 Electrolyte and Lithium anode for All-Solid-State Lithium Batteries with Ultralong Cycle Life

Zhihua Zhang et al.

ACS APPLIED MATERIALS & INTERFACES (2018)

添加到收藏夹

Article Chemistry, Physical

Flexible, Scalable, and Highly Conductive Garnet-Polymer Solid Electrolyte Templated by Bacterial Cellulose

Hua Xie et al.

ADVANCED ENERGY MATERIALS (2018)

添加到收藏夹

Article Chemistry, Physical

PEO/garnet composite electrolytes for solid-state lithium batteries: From ceramic-in-polymer to polymer-in-ceramic

Long Chen et al.

NANO ENERGY (2018)

添加到收藏夹

Article Nanoscience & Nanotechnology

Stabilizing the Interface of NASICON Solid Electrolyte against Li Metal with Atomic Layer Deposition

Yulong Liu et al.

ACS APPLIED MATERIALS & INTERFACES (2018)

添加到收藏夹

Article Chemistry, Multidisciplinary

Li3N-Modified Garnet Electrolyte for All-Solid-State Lithium Metal Batteries Operated at 40 degrees C

Henghui Xu et al.

NANO LETTERS (2018)

添加到收藏夹

Article Chemistry, Multidisciplinary

Conformal, Nanoscale ZnO Surface Modification of Garnet-Based Solid-State Electrolyte for Lithium Metal Anodes

Chengwei Wang et al.

NANO LETTERS (2017)

添加到收藏夹

Article Chemistry, Multidisciplinary

Rapid Thermal Annealing of Cathode-Garnet Interface toward High-Temperature Solid State Batteries

Boyang Liu et al.

NANO LETTERS (2017)

添加到收藏夹

Article Chemistry, Multidisciplinary

Transient Behavior of the Metal Interface in Lithium Metal-Garnet Batteries

Kun (Kelvin) Fu et al.

ANGEWANDTE CHEMIE-INTERNATIONAL EDITION (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Characterization of Sputter-Deposited LiCoO2 Thin Film Grown on NASICON-type Electrolyte for Application in All-Solid-State Rechargeable Lithium Battery

Hee-Soo Kim et al.

ACS APPLIED MATERIALS & INTERFACES (2017)

添加到收藏夹

Article Chemistry, Physical

Interface Stability in Solid-State Batteries

William D. Richards et al.

CHEMISTRY OF MATERIALS (2016)

添加到收藏夹

Article Chemistry, Physical

Electrochemical Nature of the Cathode Interface for a Solid-State Lithium-Ion Battery: Interface between LiCoO2 and Garnet-Li7La3Zr2O12

Kyusung Park et al.

CHEMISTRY OF MATERIALS (2016)

添加到收藏夹

Article Nanoscience & Nanotechnology

Origin of Outstanding Stability in the Lithium Solid Electrolyte Materials: Insights from Thermodynamic Analyses Based on First-Principles Calculations

Yizhou Zhu et al.

ACS APPLIED MATERIALS & INTERFACES (2015)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Influence of Co3O4 addition on the ionic conductivity and microstructural properties of yttria-stabilized zirconia (8YSZ)

Bulent Aktas et al.

INTERNATIONAL JOURNAL OF MATERIALS RESEARCH (2014)

添加到收藏夹

Article Chemistry, Physical

In-situ Li7La3Zr2O12/LiCoO2 interface modification for advanced all-solid-state battery

Takehisa Kato et al.

JOURNAL OF POWER SOURCES (2014)

添加到收藏夹

Article Chemistry, Physical

Fabrication of all-solid-state lithium battery with lithium metal anode using Al2O3-added Li7La3Zr2O12 solid electrolyte

Masashi Kotobuki et al.

JOURNAL OF POWER SOURCES (2011)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.