☆ 4.7 Article

Fretting wear resistance at ambient and elevated temperatures of 316 stainless steel improved by laser cladding with Co-based alloy/WC/CaF2 composite coating

OPTICS AND LASER TECHNOLOGY (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Mechanical

Dependence of fretting wear on the microstructure characteristics and impact on the subsurface stability of a metastable β titanium alloy

Ke Hua et al.

Summary: The study focused on the fretting behaviors of a metastable beta titanium alloy with different microstructures. Results showed that the wear volume is more sensitive to stroke amplitude, and mixed abrasive-adhesive wear is dominant. Different microstructural features significantly affect wear resistance and subsurface microstructure stability. The findings provide valuable data for predicting fatigue life after fretting.

TRIBOLOGY INTERNATIONAL (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

The determining role of carbon addition on mechanical performance of a non-equiatomic high-entropy alloy

Xiaolin Li et al.

Summary: The mechanical properties and deformation mechanism of a C-doped interstitial high-entropy alloy were studied, and an excellent combination of strength and ductility was achieved through cold rolling and annealing. The deformation mechanism was found to involve dislocation slip, deformation-driven phase transformation, and deformation twinning. The simultaneous effect of phase transformation and mechanical twinning delayed the shrinkage and improved the tensile strength and plasticity.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

High-temperature oxidation and wear properties of TiC-reinforced CrMnFeCoNi high entropy alloy composite coatings produced by laser cladding

Da Sun et al.

Summary: Extensive research has been conducted on high entropy alloy composite coatings reinforced with micro-sized ceramic particles at room temperature. However, studies on their properties at high temperatures are limited. This study investigated the oxidation and tribological properties of CrMnFeCoNi/xTiC composite coatings produced by laser cladding at a temperature of 600 degrees C. The addition of TiC promoted the oxidation process and the formation of a wear-resistant intermediate layer. The coatings exhibited low hardness, low wear rate, and high coefficient of friction due to the formation of a composite oxide film on the worn surface with good adhesion to the matrix.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Preparation and high-temperature tribological performance of laser clad MoNi coatings with chromium addition

Gongjun Cui et al.

Summary: The study investigated the effect of Cr content on the microstructure and tribological performance of high-temperature wear-resistant MoNi matrix coatings, finding that 7 wt% Cr was the optimal content, providing the best wear resistance over a wide temperature range.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Optics

Effect of WC-12Co on the mechanical and wear performance of laser melting deposition nickel-based alloy

Ruifeng Di et al.

Summary: This study investigated the effect of WC-12Co on microstructure, tribological characteristics, and mechanical properties of Ni-Cu alloy using laser melting deposition. The results showed that WC particles dissolved and diffused during laser cladding, resulting in finer microstructure and compound formation in Ni-Cu alloy. WC particles improved the hardness, wear resistance, and tensile strength of Ni-Cu alloy, but had limited effect on plasticity.

OPTICS AND LASER TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure, hardness and slurry erosion-wear behaviors of high-speed laser cladding Stellite 6 coatings prepared by the inside-beam powder feeding method

Ziyi Yang et al.

Summary: In this study, Stellite 6 coatings were prepared by the high-speed laser cladding technique and their microstructure, hardness, and erosion-wear behaviors were investigated. The results showed that the coatings exhibited excellent hardness and erosion resistance.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Stellite3-Ti3SiC2-Cu composite coatings on IN718 by laser cladding towards improved wear and oxidation resistance

Shi-Yi Zhang et al.

Summary: A series of Stellite3 matrix composite coatings containing Ti3SiC2/Cu were prepared by laser cladding to improve the wear and oxidation resistance of IN718 superalloy. The coatings exhibited higher microhardness and improved wear resistance, with the Stellite3-5%Ti3SiC2-10%Cu coating performing the best. Furthermore, the Stellite3-10% Ti3SiC2 coating showed better oxidation and wear resistance under high temperatures.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Mechanical

Investigation on fretting wear mechanism of 316 stainless steel induced by Ni dissolution during pre-immersion corrosion in the liquid lead-bismuth eutectic (LBE)

Ke Hua et al.

Summary: The study investigated the effect of pre-immersion corrosion in LBE on the fretting behavior of AISI 316 stainless steel. It was found that long-duration corrosion led to a degradation in wear resistance due to the formation of a large oxide layer and fretting fatigue wear becoming dominant.

TRIBOLOGY INTERNATIONAL (2022)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

The synergistic effect of wear-corrosion in stainless steels: A review

Majdouline Maher et al.

Summary: The consequence of coupling wear and corrosion is not simply the sum of wear and corrosion occurring separately. The synergistic effect means that corrosion is accelerated by the removal of the passivating layer due to wear, and corrosion can also accelerate abrasion when a brittle surface layer is formed and subsequently removed by abrasion. The synergism between wear and corrosion is complex and the interaction between mechanical and chemical factors governing tribocorrosion is not fully understood.

MATERIALS TODAY-PROCEEDINGS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of residual thermal stress on mechanical behavior of cermets with different grain sizes

Jinghong Chen et al.

Summary: The distribution of residual thermal stress in cermets and its interaction with applied stress were studied in WC-Co cemented carbides. The study found that WC grain size significantly influences the residual thermal stress, with smaller grain size, lower Co thin-layer proportion, and higher triple junction proportion beneficial for reducing stress concentration. In cermets with residual thermal stress, the metallic binder shows an increasing strain response rate under external loading, providing insights into adjusting stress distribution for improved mechanical properties.

ACTA MATERIALIA (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

Improving surface resistance to wear and corrosion of nickel-aluminum bronze by laser-clad TaC/Co-based alloy composite coatings

Zhiyuan Li et al.

Summary: The TaC/Stellite X-40 Co-based composite coatings were successfully fabricated on NAB substrates through laser surface cladding, resulting in improved wear and corrosion resistances in marine environments. The incorporation of carbide and intermetallic reinforcements in the gamma-Co matrix led to enhanced wear and electrochemical corrosion resistances. With a higher TaC content in the coatings, the microhardness increased and the wear rate decreased significantly, indicating improved performance of the composite coatings.

SURFACE & COATINGS TECHNOLOGY (2021)

添加到收藏夹

Article Engineering, Mechanical

Effect of the frequency on fretting corrosion behavior between Alloy 690TT tube and 405 stainless steel plate in high temperature pressurized water

Yusheng Zhang et al.

Summary: The study investigated the effect of fretting frequency on fretting corrosion behavior between Alloy 690TT heat-exchanger tube and 405 stainless steel plate in simulated secondary water of pressurized water reactor nuclear power plants. It found that wear volume and wear coefficient of 690TT tube showed an initial increase then decrease with frequency, while those of corresponding 405 SS plate gradually increased. Friction and wear mechanisms varied accordingly, with changes in friction coefficient, dissipated energy, and wear mechanism observed.

TRIBOLOGY INTERNATIONAL (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and wear resistance of WC/Co-based coating on copper by plasma cladding

Zixin Xie et al.

Summary: The Co-based alloy coating reinforced with WC phase prepared on copper substrate by plasma cladding showed improved hardness and wear resistance as the WC content increased. The morphology of carbide phases in the coating changed from punctate and flower to block and dendrite, leading to an increase in average hardness.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

添加到收藏夹

Article Chemistry, Physical

Wear and high-temperature oxidation resistances of AlNbTaZrx high-entropy alloys coatings fabricated on Ti6Al4V by laser cladding

P. Zhao et al.

Summary: The AlNbTaZrx high-entropy alloys (HEAs) coatings were successfully fabricated on Ti6Al4V by laser cladding to address the poor wear and high-temperature oxidation resistance issues. The microstructural evolution and changes in wear and high-temperature oxidation behaviors with x were investigated, showing that coatings with x = 0.8 exhibited the best performance.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

High-temperature abrasive wear characteristics of H13 steel modified by laser remelting and cladded with Stellite 6 and Stellite 6/30% WC

Debapriya Patra Karmakar et al.

Summary: The study analyzed the high-temperature abrasive wear behavior of H13 steel surfaces modified by laser melting and cladding, finding that the Stellite 6/WC composite cladding had relatively lower wear loss and performed the best in the current temperature range.

SURFACE & COATINGS TECHNOLOGY (2021)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

Miao Hu et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

添加到收藏夹

Review Engineering, Mechanical

A review of fretting study on nuclear power equipment

Zhen-bing Cai et al.

TRIBOLOGY INTERNATIONAL (2020)

添加到收藏夹

Article Optics

Enhanced wear resistance and new insight into microstructure evolution of in-situ (Ti,Nb)C reinforced 316 L stainless steel matrix prepared via laser cladding

Mingyang Zhang et al.

OPTICS AND LASERS IN ENGINEERING (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructure and tribological properties of laser in-situ synthesized Ti3Al composite coating on Ti-6Al-4V

Wenbin Zhang et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Friction and wear properties of CrSi-based coatings for nuclear fuel cladding

Xiujie He et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Ceramics

Microhardness and wear resistance of Al2O3-TiB2-TiC ceramic coatings on carbon steel fabricated by laser cladding

Zhaoliang Li et al.

CERAMICS INTERNATIONAL (2019)

添加到收藏夹

Article Engineering, Mechanical

Running condition and material response fretting maps of incoloy 800 steam generator tubes against AISI 304L pads in air and room temperature

S. R. Soria et al.

TRIBOLOGY INTERNATIONAL (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

High temperature wear resistance and thermal fatigue behavior of Stellite-6/WC coatings produced by laser cladding with Co-coated WC powder

Guangyuan Wang et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)

添加到收藏夹

Article Optics

Effects of laser power on friction-wear performances of laser thermal sprayed Cr3C2-NiCr composite coatings at elevated temperatures

Hanyun Wu et al.

OPTICS AND LASER TECHNOLOGY (2019)

添加到收藏夹

Article Optics

Microstructure and high temperature wear behaviour of in-situ TiC reinforced AlCoCrFeNi-based high-entropy alloy composite coatings fabricated by laser cladding

Hao Liu et al.

OPTICS AND LASER TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructure and laser irradiation characteristics of TiC-free and TiC-doped tungsten-based coatings prepared by supersonic atmospheric plasma spraying

Qingyu Hou et al.

SURFACE & COATINGS TECHNOLOGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fretting wear comparison of cladding materials for reactor fuel cladding application

Thomas C. Winter et al.

JOURNAL OF NUCLEAR MATERIALS (2018)

添加到收藏夹

Review Nuclear Science & Technology

Developments of analyses on grid-to-rod fretting problems in pressurized water reactors

Zupan Hu

PROGRESS IN NUCLEAR ENERGY (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

Microstructure and properties of in-situ TiN reinforced laser cladding CoCr2FeNiTix high-entropy alloy composite coatings

Yaxiong Guo et al.

SURFACE & COATINGS TECHNOLOGY (2018)

添加到收藏夹

Article Engineering, Manufacturing

Development and characterization of multilayer laser cladded high speed steels

N. Ur Rahman et al.

ADDITIVE MANUFACTURING (2018)

添加到收藏夹

Article Nuclear Science & Technology

The effect of coupled wear and creep during grid-to-rod fretting

Hai Wang et al.

NUCLEAR ENGINEERING AND DESIGN (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

A research on the corrosion and stress corrosion cracking susceptibility of 316L stainless steel exposed to supercritical water

Xianglong Guo et al.

CORROSION SCIENCE (2017)

添加到收藏夹

Article Optics

Microstructure, microhardness and corrosion resistance of Stellite-6 coatings reinforced with WC particles using laser cladding

Dariusz Bartkowski et al.

OPTICS AND LASER TECHNOLOGY (2015)

添加到收藏夹

Article Engineering, Manufacturing

Formation of VC-composite surface layer on high C-Cr bearing tool steel by laser surface cladding

Hashem F. EI-Labban et al.

JOURNAL OF MANUFACTURING PROCESSES (2015)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

In-situ dendrite reinforced Dy-based amorphous matrix composites

Zhang Xiao-feng et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2009)

添加到收藏夹

Article Materials Science, Coatings & Films

Cladding with Stellite 6+WC using a YAG laser robot system

G. J. Xu et al.

SURFACE ENGINEERING (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes

JW Yeh et al.

ADVANCED ENGINEERING MATERIALS (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.