相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Microstructure estimation and validation of ER110S-G steel structures produced by wire and arc additive manufacturing
V. Mishra et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)
On the Microstructure Development under Cyclic Temperature Conditions during WAAM of Microalloyed Steels
Chang Huang et al.
METALS (2022)
Transient thermal dissipation efficiency based method for topology optimization of transient heat conduction structures
Shuhao Wu et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)
Mechanical and microstructural testing of wire and arc additively manufactured sheet material
Pinelopi Kyvelou et al.
MATERIALS & DESIGN (2020)
Increasing the manufacturing efficiency of WAAM by advanced cooling strategies
Uwe Reisgen et al.
WELDING IN THE WORLD (2020)
Fast Detection of Heat Accumulation in Powder Bed Fusion Using Computationally Efficient Thermal Models
Rajit Ranjan et al.
MATERIALS (2020)
FEM-thermodynamic simulation methodology to predict the influence of t8/5 on the coarse grain heat-affected zone of a Cr-Mo low-alloy steel pipe
Paulo Henrique Grossi Dornelas et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Cellular size dependence on the strength of additively manufactured austenitic stainless steel
Decheng Kong et al.
MATERIALS LETTERS (2020)
Topology optimization considering overhang constraint in additive manufacturing
Kaiqing Zhang et al.
COMPUTERS & STRUCTURES (2019)
Topology optimization for minimizing the maximum temperature of transient heat conduction structure
Shuhao Wu et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2019)
Additive manufacturing of metallic components - Process, structure and properties
T. DebRoy et al.
PROGRESS IN MATERIALS SCIENCE (2018)
Current and future trends in topology optimization for additive manufacturing
Jikai Liu et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2018)
Continuous front propagation-based overhang control for topology optimization with additive manufacturing
Emiel van de Ven et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2018)
An additive manufacturing filter for topology optimization of print-ready designs
Matthijs Langelaar
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2017)
Effect of strut orientation on the microstructure heterogeneities in AlSi10Mg lattices processed by selective laser melting
Pauline Delroisse et al.
SCRIPTA MATERIALIA (2017)
Topology optimization considering overhang constraints: Eliminating sacrificial support material in additive manufacturing through design
Andrew T. Gaynor et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2016)
Additive manufacturing of strong and ductile Ti-6Al-4V by selective laser melting via in situ martensite decomposition
W. Xu et al.
ACTA MATERIALIA (2015)
Rationalization of Microstructure Heterogeneity in INCONEL 718 Builds Made by the Direct Laser Additive Manufacturing Process
Yuan Tian et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
Correlation of Yield Strength and Tensile Strength with Hardness for Steels
E. J. Pavlina et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2008)
Effect of weld thermal cycle on microstructure and fracture toughness of simulated heat-affected zone for a 800 MPa grade high strength low alloy steel
Yaowu Shi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Microstructural evolution in laser-deposited multilayer Ti-M-4V builds: Part I. Microstructural characterization
SM Kelly et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2004)
Microstructural evolution in laser-deposited multilayer Ti-6AI-4V builds: Part II. Thermal modeling
SM Kelly et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2004)
Topology optimization of non-linear elastic structures and compliant mechanisms
TE Bruns et al.
COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING (2001)