☆ 4.7 Article

Suppressing hydrogen blistering in a magnesium-rich healable laser powder bed fusion aluminum alloy analyzed by in-situ high resolution techniques

MATERIALS & DESIGN (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Multidisciplinary Sciences

Hydrogen trapping and embrittlement in high-strength Al alloys

Huan Zhao et al.

Summary: As regulations on greenhouse gas emissions from transportation become stricter, it has become necessary to re-examine the materials used for vehicles. While high-strength aluminum alloys commonly used in aircrafts can help reduce the weight of automobiles, they are prone to environmental degradation. Hydrogen 'embrittlement' is often considered the main cause of this degradation, but the exact mechanisms behind this failure are not well understood due to the challenges in analyzing hydrogen at the atomic scale. In this study, near-atomic-scale analysis of hydrogen trapped in second-phase particles and at grain boundaries in a high-strength aluminum alloy was performed. These observations guided atomistic ab initio calculations which revealed that the co-segregation of alloying elements and hydrogen promotes grain boundary decohesion, and the strong partitioning of hydrogen into the second-phase particles removes solute hydrogen from the matrix, thus preventing hydrogen embrittlement. This research advances our understanding of hydrogen-assisted embrittlement in aluminum alloys and highlights the role of hydrogen traps in reducing cracking and guiding new alloy design.

NATURE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

A new healing strategy for metals: Programmed damage and repair

Mariia Arseenko et al.

Summary: Self-healing strategies for metallic systems are still under-developed, but this study proposes a new strategy based on damage localization particles that can be healed by heat treatment. The strategy was successfully validated with a commercial aluminum alloy, showing that short and low temperature heating can repair micron-sized damage.

ACTA MATERIALIA (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

High-temperature oxidation performance of Ni-based GH3536 superalloy fabricated by laser powder bed fusion

Shiling Min et al.

Summary: The study explores the impact of microstructure on the short-term and long-term oxidation behaviors of GH3536 superalloy fabricated by laser powder bed fusion. It is found that the cellular structure produced during the LPBF process enhances oxidation resistance by accelerating the formation of a protective film.

NPJ MATERIALS DEGRADATION (2022)

添加到收藏夹

Review Materials Science, Multidisciplinary

Laser Powder Bed Fusion of Potential Superalloys: A Review

Prince Valentine Cobbinah et al.

Summary: LPBF technology can produce high-precision and complex geometric components, with TiAl-based alloys and HEAs seen as potential replacements for nickel-based superalloys in high temperature structural applications. Proper control and alloy manipulation are crucial for optimizing microstructures.

METALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Nanoscale periodic gradients generated by laser powder bed fusion of an AlSi10Mg alloy

Williams Lefebvre et al.

Summary: The study reveals the formation of a periodic microstructural pattern in an AlSi10Mg alloy through laser powder bed fusion (LPBF) using scanning transmission electron microscopy and atom probe tomography. It discusses the non-equilibrium structures and compositional fields resulting from the ultrafast cooling of the LPBF process and identifies clusters in the supersaturated aluminium solid solution retained by the LPBF process.

MATERIALS & DESIGN (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Ef fi cient optimization methodology for laser powder bed fusion parameters to manufacture dense and mechanically sound parts validated on AlSi12 alloy

Julie Gheysen et al.

Summary: An innovative methodology has successfully optimized the parameters of laser-melted metal AlSi12 using fewer samples and experiments, resulting in better mechanical properties.

MATERIALS & DESIGN (2021)

添加到收藏夹

Article Multidisciplinary Sciences

Unravelling the multi-scale structure-property relationship of laser powder bed fusion processed and heat-treated AlSi10Mg

P. Van Cauwenbergh et al.

Summary: The study uncovers the relationship between the microstructure and macroscopic material properties of LPBF-processed AlSi10Mg, identifying grain refinement and Si supersaturation as crucial elements for achieving superior mechanical and thermal properties during heat treatment. Additionally, an electrical conductivity model accurately predicts Si solute concentration in LPBF-processed and heat-treated AlSi10Mg, facilitating understanding of microstructural evolution during heat treatment. The LPBF-processed and heat-treated AlSi10Mg conditions exhibit a range of superior mechanical properties compared to the mould-cast T6 reference condition.

SCIENTIFIC REPORTS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hydrogen Trapping in Mg2Si and Al7FeCu2 Intermetallic Compounds in Aluminum Alloy: First-Principles Calculations

Masatake Yamaguchi et al.

MATERIALS TRANSACTIONS (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence on microstructure, strength and ductility of build platform temperature during laser powder bed fusion of AlSi10Mg

Juan Guillermo Santos Macias et al.

ACTA MATERIALIA (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Damage mechanisms in selective laser melted AlSi10Mg under as built and different post-treatment conditions

Lv Zhao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

添加到收藏夹

Article Nanoscience & Nanotechnology

Ductilisation and fatigue life enhancement of selective laser melted AlSi10Mg by friction stir processing

Juan Guillermo Santos Macias et al.

SCRIPTA MATERIALIA (2019)

添加到收藏夹

Article Chemistry, Multidisciplinary

Self-Healing Phenomena in Metals

Niels van Dijk et al.

ADVANCED MATERIALS INTERFACES (2018)

添加到收藏夹

Article Chemistry, Physical

Low temperature annealing dedicated to AlSi10Mg selective laser melting products

J. Fiocchi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Change in microstructure of selectively laser melted AlSi10Mg alloy with heat treatments

Naoki Takata et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fast in situ 3D nanoimaging: a new tool for dynamic characterization in materials science

Julie Villanova et al.

MATERIALS TODAY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Susceptibility of ternary aluminum alloys to cracking during solidification

Jiangwei Liu et al.

ACTA MATERIALIA (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Microstructure and wear behavior of in-situ hypereutectic Al-high Si alloys produced by selective laser melting

Nan Kang et al.

MATERIALS & DESIGN (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

A selective laser melting and solution heat treatment refined Al-12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility

X. P. Li et al.

ACTA MATERIALIA (2015)

添加到收藏夹

Article Engineering, Industrial

Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg

Christian Weingarten et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Revision Of The Solvus Limit Of Al-Mg2Si Pseudo Binary Phase Diagram

Matias N. Amado et al.

INTERNATIONAL CONGRESS OF SCIENCE AND TECHNOLOGY OF METALLURGY AND MATERIALS, SAM - CONAMET 2013 (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

In situ electron microscopy investigation of void healing in an Al-Mg-Er alloy at a low temperature

M. Song et al.

ACTA MATERIALIA (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Severe Plastic Deformation Induced Sensitization of Cryo-milled Nanocrystalline Al-7.5 Mg

Ramasis Goswami et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Defect-induced Au precipitation in Fe-Au and Fe-Au-B-N alloys studied by in situ small-angle neutron scattering

S. Zhang et al.

ACTA MATERIALIA (2013)

添加到收藏夹

Article Chemistry, Multidisciplinary

Self-Healing Materials

Martin D. Hager et al.

ADVANCED MATERIALS (2010)

添加到收藏夹

Article Nanoscience & Nanotechnology

Self-healing of deformation damage in underaged Al-Cu-Mg alloys

S. Hautakangas et al.

SCRIPTA MATERIALIA (2008)

添加到收藏夹

Article Nanoscience & Nanotechnology

Precipitation induced densification in a sintered Al-Zn-Mg-Cu alloy

RN Lumley et al.

SCRIPTA MATERIALIA (2006)

添加到收藏夹

Article Crystallography

Grown-in defects in silicon crystals

K Nakamura et al.

JOURNAL OF CRYSTAL GROWTH (2002)

添加到收藏夹

Article Materials Science, Multidisciplinary

Shrinkage and splitting of microcracks under pressure simulated by the finite-element method

PZ Huang et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2002)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.