☆ 4.5 Article

Si-containing interlayer using tetramethylsilene for diamondlike carbon film adhesion on low-alloy steel: The role of the interlayer deposition time

JOURNAL OF VACUUM SCIENCE & TECHNOLOGY A (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Controlling of Chemical Bonding Structure, Wettability, Optical Characteristics of SiCN:H (SiC:H) Films Produced by PECVD Using Tetramethylsilane and Ammonia Mixture

Evgeniya Ermakova et al.

Summary: The PECVD SiC:H (SiCN:H) films were synthesized using tetramethylsilane (TMS) as a precursor and helium or ammonia as a source of nitrogen. The deposition conditions greatly influenced the structure and properties of the films. Ammonia gas effectively incorporated nitrogen atoms into the films, resulting in the transformation of film composition from SiC:H to SiN:H. Plasma treatment significantly altered the surface characteristics of the SiCN films, as observed through X-ray photoelectron spectroscopy, atomic force microscopy, and contact angle measurements.

COATINGS (2023)

添加到收藏夹

Article Engineering, Chemical

The Effect of the Process Parameters on the Growth Rate and Composition of the Anti Scratch Films Deposited from TEOS by AP-PECVD on Polycarbonate

Anastasia S. Bil et al.

Summary: This paper reports on a study of anti-scratch silica-like coatings deposited on polycarbonate using an atmospheric pressure dielectric barrier discharge. Plasma pretreatment in pure helium is found to significantly increase the PC surface energy and improve adhesion of the films. However, the introduction of oxygen did not show significant improvement in the coatings' properties.

PLASMA CHEMISTRY AND PLASMA PROCESSING (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Study on the Tribological Behavior of Wear and Friction Coefficient on AISI M35 High-Speed Steel with and without DLC Coating

Paulo Sergio Martins et al.

Summary: This study evaluated the tribological behavior of DLC coating on AISI M35 steel and found that the coating exhibited better wear resistance compared to high-speed steel, with significant reductions in micro-abrasive wear and friction coefficient during sliding.

MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Well-adhered hydrogenated amorphous carbon thin films on ferrous alloy using silicon-containing interlayers at low temperatures

V. Piroli et al.

Summary: Depositing a-SiCx:H interlayers at low temperatures using tetramethylsilane under low background pressure can enhance the adhesion of a-C:H thin films. The reduced oxygen content within the interlayer at low background pressure contributes to the significant increase in adhesion.

VACUUM (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

The DLC Coating on 316L Stainless Steel Stochastic Voronoi Tessellation Structures Obtained by Binder Jetting Additive Manufacturing for Potential Biomedical Applications

Dorota Laskowska et al.

Summary: This study fabricated stochastic porous structures based on Voronoi tessellation using binder jetting technology and modified them with DLC coating. The conditions of the RF PACVD process allowed for the deposition of continuous and tightened DLC coatings, as confirmed by various characterizations and analyses.

COATINGS (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Tribological CCF-PEEK transfer film growth on cutting tool coating

Xin Dong et al.

Summary: The study investigates the transfer film growth of continuous carbon fiber reinforced thermoplastic poly-ether-ether-ketone (CCF-PEEK) on cutting tool coating. It is found that continuous CCF-PEEK transfer films can grow on titanium nitride (TiN), titanium aluminum nitride (TiAlN), and diamond, and increasing load promotes the growth. Additionally, DLC can be used as countermate surfaces of CCF-PEEK composite with low friction and minimal CCF-PEEK wear debris.

SURFACE ENGINEERING (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

Study of the methane flow influence in the micro-tribology behavior of DLC coatings deposited by PECVD: a Raman analysis

Cesar Daniel Rivera-Tello et al.

Summary: This study investigated the influence of methane flow on the micro-tribological behavior of diamond-like carbon coatings using Raman spectroscopy. The results showed a direct relationship between methane flow and coating thickness, and the analysis of Raman spectra helped establish the properties of the carbon coatings. Additionally, the study demonstrated a strong correlation between wear resistance and hardness with Raman parameters.

CARBON LETTERS (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

DLC (H) coated 13Cr SMSS by high-pulsed power CVD technique

Yukun Zhang et al.

Summary: Increasing the bias voltage was found to enhance the hardness and tribological properties of DLC films, leading to denser films with reduced grain size and surface roughness. Films with high H/E* and H-2/E*(3) ratios exhibited high elastic modulus and resistance to plastic deformation, reducing wear loss and providing solid lubrication through localized graphitization.

SURFACE ENGINEERING (2021)

添加到收藏夹

Article Multidisciplinary Sciences

Effects of silicon doping on low-friction and high-hardness diamond-like carbon coating via filtered cathodic vacuum arc deposition

Jae-Il Kim et al.

Summary: In this study, the tribological characteristics of Si-doped diamond-like carbon coating were investigated against a SUJ2 ball. It was found that a moderate Si fraction could significantly decrease the coefficient of friction and running-in period, leading to the formation of a low-friction tribofilm. However, excessive Si doping beyond a critical point resulted in the destruction of the film due to reduced hardness.

SCIENTIFIC REPORTS (2021)

添加到收藏夹

Article Chemistry, Physical

Abrasive Wear, Scuffing and Rolling Contact Fatigue of DLC-Coated 18CrNiMo7-6 Steel Lubricated by a Pure and Contaminated Gear Oil

Waldemar Tuszynski et al.

Summary: The study suggests that to reduce abrasion, scuffing, and pitting of gears in extreme mining conveyor conditions, the deposition of W-DLC/CrN coating should be considered, as it also provides good protection when the lubricating oil is contaminated.

MATERIALS (2021)

添加到收藏夹

Article Chemistry, Physical

On the adhesion of diamond-like carbon coatings deposited by low-pressure plasma on 316L stainless steel

Gabriel Morand et al.

Summary: The study investigates the use of plasma treatment to generate shallow metallic carbide layers for promoting DLC adhesion on 316L stainless steel surfaces. The presence of metallic carbides stabilizes and enhances DLC thin film deposition, improving adhesion. The research demonstrates that plasma can offer new insights into overcoming the lack of adhesion of DLC thin films on SS metallic surfaces.

SURFACE AND INTERFACE ANALYSIS (2021)

添加到收藏夹

Review Chemistry, Multidisciplinary

Diamond-Like Carbon (DLC) Coatings: Classification, Properties, and Applications

Dipen Kumar Rajak et al.

Summary: DLC coatings have gained significant interest in science and engineering applications, with a wide range of amorphous carbon materials. Their diverse properties make them suitable for various industries, and their lifespan is influenced by constituent elements and manufacturing techniques. Researchers have conducted numerous experiments to understand DLC coatings and their capabilities, making them a promising alternative to traditional coating methods.

APPLIED SCIENCES-BASEL (2021)

添加到收藏夹

Article Polymer Science

Structural and optical properties o plasma-deposited a-C:H:Si:O:N films

Juliana Feletto Silveira Costa Lopes et al.

Summary: Thin a-C:H:Si:O:N films were deposited using plasma containing hexamethyldisiloxane, oxygen, and nitrogen at varying oxygen partial pressure. The deposition rates ranged from 10 to 27 nm min(-1). The films exhibited a surface roughness of around 10 nm and contained characteristic groups such as C=C, C=O, Si-C, and Si-O-Si. As the oxygen partial pressure increased, the films showed lower carbon and nitrogen content but higher oxygen and silicon content. The films had refractive indices around 1.5 and optical energy gaps that decreased from around 3.3 to 2.3 eV with increasing oxygen partial pressure. The Urbach energy decreased with increasing optical gap, indicating the characteristic of amorphous materials, and suggesting their potential as transparent barrier coatings.

POLIMEROS-CIENCIA E TECNOLOGIA (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

SiOx Top Layer on DLC Films for Atomic Oxygen and Ozone Corrosion Protection in Aerospace Applications

L. L. Ferreira et al.

Summary: The study deposited SiOx-DLC thin films as a top layer on Ti-6Al-4V substrates to enhance resistance against atomic oxygen and ozone corrosion for use in Low Earth Orbit (LEO) satellites. The SiOx-DLC top layer significantly reduced corrosion rate by two orders of magnitude and increased critical load.

MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2021)

添加到收藏夹

Article Chemistry, Multidisciplinary

Evaluation of the sp3/sp2 ratio of DLC films by RF-PECVD and its quantitative relationship with optical band gap

Hongxun Sheng et al.

Summary: The relationship between the sp(3)/sp(2) ratio of DLC films fabricated by PECVD and their E-g has been studied, resulting in a quantitative correlation. Various characterization methods like XPS, Raman spectroscopy, and IR absorption were used to determine this relationship.

CARBON LETTERS (2021)

添加到收藏夹

Article Chemistry, Physical

Pure carbon conductive transparent electrodes synthetized by a full laser deposition and annealing process

F. Stock et al.

APPLIED SURFACE SCIENCE (2020)

添加到收藏夹

Article Physics, Applied

SiCN:H thin films deposited by MW-PECVD with liquid organosilicon precursor: Gas ratio influence versus properties of the deposits

Beatrice Plujat et al.

PLASMA PROCESSES AND POLYMERS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Evaluation of Argon as a Carrier Gas of Liquid Material Vaporization During the Plasma-Enhanced Chemical Vapor Deposition (PECVD) Silicon Oxide Process

Cheong-Il Ryu et al.

SCIENCE OF ADVANCED MATERIALS (2020)

添加到收藏夹

Article Chemistry, Physical

PECVD of Hexamethyldisiloxane Coatings Using Extremely Asymmetric Capacitive RF Discharge

Ziga Gosar et al.

MATERIALS (2020)

添加到收藏夹

Article Nanoscience & Nanotechnology

Substrate Bias Voltage Tailoring the Interfacial Chemistry of a-SiCx:H: A Surprising Improvement in Adhesion of a-C:H Thin Films Deposited on Ferrous Alloys Controlled by Oxygen

Angela E. Crespi et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

添加到收藏夹

Article Physics, Applied

Computational study on silicon oxide plasma enhanced chemical vapor deposition (PECVD) process using tetraethoxysilane/oxygen/argon/ helium

Hu Li et al.

JAPANESE JOURNAL OF APPLIED PHYSICS (2019)

添加到收藏夹

Article Optics

The Effect of Nonequilibrium Synthesis Conditions on the Structure and Optical Properties of Amorphous Carbon Films

A. P. Ryaguzov et al.

OPTICS AND SPECTROSCOPY (2019)

添加到收藏夹

Article Chemistry, Physical

Tribological properties of Ti-doped diamond-like carbon coatings under dry friction and PAO oil lubrication

Youzhi Guo et al.

SURFACE AND INTERFACE ANALYSIS (2019)

添加到收藏夹

Article Materials Science, Coatings & Films

Optical and tribological properties of decorative titanium, carbonitride coatings

L. Milschi et al.

SURFACE ENGINEERING (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

Enhancing the adhesion of diamond-like carbon films to steel substrates using silicon-containing interlayers

Soraya Delfani-Abbariki et al.

SURFACE & COATINGS TECHNOLOGY (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

A comprehensive study on different silicon-containing interlayers for a-C:H adhesion on ferrous alloys

C. D. Boeira et al.

THIN SOLID FILMS (2018)

添加到收藏夹

Article Chemistry, Physical

The effect of interface electrostatic interaction based on acid-base theory on friction behavior

Li Qiang et al.

SURFACE AND INTERFACE ANALYSIS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of hydrogen etching on the adhesion of coated ferrous alloy by hydrogenated amorphous carbon deposited at low temperature

A. E. Crespi et al.

VACUUM (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of Elements on the Corrosion Resistance of DLC Films

Nutthanun Moolsradoo et al.

ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2017)

添加到收藏夹

Article Materials Science, Coatings & Films

Physicochemical structure of SiCX:H to improve DLC adhesion on steel

E. R. Petry et al.

SURFACE ENGINEERING (2016)

添加到收藏夹

Article Materials Science, Coatings & Films

The influence of different silicon adhesion interlayers on the tribological behavior of DLC thin films deposited on steel by EC-PECVD

F. Cemin et al.

SURFACE & COATINGS TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Coatings & Films

Structural and tribological properties of TiC-DLC coatings deposited by RCAE-PVD at various bias voltages

M. J. Mosayebi et al.

SURFACE ENGINEERING (2015)

添加到收藏夹

Article Materials Science, Coatings & Films

History of diamond-like carbon films - From first experiments to worldwide applications

Klaus Bewilogua et al.

SURFACE & COATINGS TECHNOLOGY (2014)

添加到收藏夹

Article Materials Science, Coatings & Films

Deposition of amorphous hydrogenated carbon films on steel surfaces through the enhanced asymmetrical modified bipolar pulsed-DC PECVD method

G. Capote et al.

SURFACE & COATINGS TECHNOLOGY (2014)

添加到收藏夹

Article Engineering, Chemical

Silane Gas Venting/Treatment Lessons Learned and Best Practices

James VanOmmeren

PROCESS SAFETY PROGRESS (2011)

添加到收藏夹

Article Materials Science, Multidisciplinary

The effect of thermal and plastic mismatch on stress distribution in diamond like carbon film under different interlayer/substrate system

Chehung Wei et al.

DIAMOND AND RELATED MATERIALS (2008)

添加到收藏夹

Article Materials Science, Coatings & Films

Influence of the deposition temperature on mechanical and tribological properties of a-C:H:Si coatings on nitrided and postoxidized steel deposited by DC-PACVD

Christian Forsich et al.

SURFACE & COATINGS TECHNOLOGY (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Adherent amorphous hydrogenated carbon films on metals deposited by plasma enhanced chemical vapor deposition

G. Capote et al.

THIN SOLID FILMS (2008)

添加到收藏夹

Article Materials Science, Coatings & Films

A comparison of DLC film properties obtained by r.f. PACVD, IBAD, and enhanced pulsed-DC PACVD

V. J. Trava-Airoldi et al.

SURFACE & COATINGS TECHNOLOGY (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparing internal stress in diamond-like carbon films with different structure

Peng Wang et al.

THIN SOLID FILMS (2007)

添加到收藏夹

Article Physics, Applied

Influence of the ion mean free path and the role of oxygen in nitriding processes

CA Figueroa et al.

JOURNAL OF APPLIED PHYSICS (2003)

添加到收藏夹

Review Materials Science, Multidisciplinary

Diamond-like amorphous carbon

J Robertson

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2002)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of gradient a-SiCx interlayer on adhesion of DLC films

BH Lung et al.

MATERIALS CHEMISTRY AND PHYSICS (2001)

添加到收藏夹

Article Chemistry, Physical

Investigation of the structure and properties of a-C:H coatings with metal and silicon containing interlayers

M Nöthe et al.

APPLIED SURFACE SCIENCE (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.