相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。Anodizing Al-Si Foundry Alloys: A Critical Review
Giulia Scampone et al.
ADVANCED ENGINEERING MATERIALS (2022)
Aluminum anodizing with simultaneous silanization for increased hydrophobicity and corrosion protection
Pedro Atz-Dick et al.
APPLIED SURFACE SCIENCE (2022)
Mechanical and tribological properties of anodic Al coatings as a function of anodizing conditions
Enkeleda Dervishi et al.
SURFACE & COATINGS TECHNOLOGY (2022)
Mechanism of hot water sealing of anodic films formed on aluminum
Sachiko Ono et al.
CORROSION SCIENCE (2021)
Influence of Fe-rich intermetallics and their segregation on anodising properties of Al-Si-Mg rheocast alloys
Baiwei Zhu et al.
SURFACE & COATINGS TECHNOLOGY (2021)
The Sealing Step in Aluminum Anodizing: A Focus on Sustainable Strategies for Enhancing Both Energy Efficiency and Corrosion Resistance
Stanley Udochukwu Ofoegbu et al.
COATINGS (2020)
Microstructural and tribological investigations of diecast and hard anodized AlSiCu alloys
Daniele Caliari et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Effects of surface roughness on scratch resistance and stress-strain fields during scratch tests
Biao Feng
AIP ADVANCES (2017)
Comparison of Measurement Methods for Secondary Dendrite Arm Spacing
Eli Vandersluis et al.
METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2017)
Application of EIS to In Situ Characterization of Hydrothermal Sealing of Anodized Aluminum Alloys: Comparison between Hexavalent Chromium-Based Sealing, Hot Water Sealing and Cerium-Based Sealing
A. Carangelo et al.
JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2016)
Anodization of Aluminium using a fast two-step process
Murugaiya Sridar Ilango et al.
JOURNAL OF CHEMICAL SCIENCES (2016)
PEO of pre-anodized Al-Si alloys: Corrosion properties and influence of sealings
M. Mohedano et al.
APPLIED SURFACE SCIENCE (2015)
Effect of Sealing on Thermal Conductivity of Aluminium Anodic Oxide Layer
Junghoon Lee et al.
JOURNAL OF NANOELECTRONICS AND OPTOELECTRONICS (2014)
The Effects of Microstructure Heterogeneities and Casting Defects on the Mechanical Properties of High-Pressure Die-Cast AlSi9Cu3(Fe) Alloys
Giulio Timelli et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
Effects of Bismuth on the Microstructure and Mechanical Properties of AlSi9Cu3(Fe) Die Casting Alloys
Stefano Ferraro et al.
LIGHT METALS TECHNOLOGY 2013 (2013)
Defect band characteristics in Mg-Al and Al-Si high-pressure die castings
C. M. Gourlay et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2007)
Comparison by SEM, TEM, and EIS of hydrothermally sealed and cold sealed aluminum anodic oxides
V Lopez et al.
JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2006)
Influence of substrate microstructure on the growth of anodic oxide layers
LE Fratila-Apachitei et al.
ELECTROCHIMICA ACTA (2004)
The influences of sealing methods on corrosion behavior of anodized aluminum alloys in NaCl solutions
Y Zuo et al.
SURFACE & COATINGS TECHNOLOGY (2003)