☆ 4.7 Article

Unusual ablation behaviors of tungsten graded network reinforced copper composites synthesized by 3D printing and infiltration sintering at ultra-high temperatures

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Twinning and antitwinning in body-centered cubic metals

Roman Groger et al.

Summary: Deformation twinning in body-centered cubic (BCC) metals occurs by shearing the crystal along specific planes, and recent studies have shown that antitwinning shear can lead to twinning in some BCC metals. Molecular statics simulations reveal that twinning can occur on both twinning and antitwinning shear in transition metals, but only on twinning shear in alpha-Fe and alkali metals. TEM diffraction pattern analyses further confirm the existence of regular twins along antitwinning shear in Nb and Cr, and exclusively on twinning shear in alpha-Fe.

COMPUTATIONAL MATERIALS SCIENCE (2023)

添加到收藏夹

Article Chemistry, Physical

A prospect of using ternary W-5 wt%V-5 wt%Ta alloy manufactured by mechanical alloying and spark plasma sintering as plasma-facing material

Hongjing Cui et al.

Summary: In this study, a ternary W alloy containing 5 wt% V and 5 wt% Ta was fabricated using mechanical alloying and spark plasma sintering. The alloy exhibited a single-phase body centered cubic structure with (V, Ta)-enriched fine grains and W-enriched grains. It showed an ultrafine grain size and higher relative density, microhardness, and strength compared to pure W. The strengthening mechanisms were analyzed, and it was found that grain refinement, densification, and solid solution played different roles in strengthening. The alloy demonstrated good irradiation resistance, which was attributed to its ultrafine grains and higher compressive and tensile strength. The potential application of the W-5 wt%V-5 wt%Ta alloy as a plasma-facing material was suggested.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

W-Cu/Cu composite electrodes fabricated via laser surface alloying

Hongbin Xie et al.

Summary: Laser surface alloying was employed to prepare a novel W-Cu/Cu composite with high W content on the surface but low W content for the whole composite, exhibiting a lower arc ablation rate than the commercial one. The study opens a door to overcome the trade-off of the ablation resistance and W consumption of the W-Cu electrodes.

MATERIALS CHARACTERIZATION (2022)

添加到收藏夹

Article Nuclear Science & Technology

Improved strength and heat transfer of W/Cu joints via surface nano-activation of W

Hanyu Wang et al.

Summary: This research presents a novel method for enhancing direct alloying of tungsten (W) and copper (Cu) using nanoporous structures, without using interlayer metals. The results show that surface nano-activation of W can significantly promote direct alloying, improve the tensile strength of W/Cu joints, and enhance their thermal diffusivity.

FUSION ENGINEERING AND DESIGN (2022)

添加到收藏夹

Article Engineering, Manufacturing

Fabrication and experimental investigation of arc erosion behavior in W/Cu functionally graded composites

Ramezan Ali Mahdavinejad et al.

Summary: This study proposed a functionally graded composite technique to produce W/Cu alloy electrical contact material, finding that the intermediate layer had completed the sintering process with low porosity and high hardness. It was also discovered that multi-layered FGC showed better erosion resistance, improved heat transfer, and reduced surface damage.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fabrication and characterization of W/Cu/Ni-based high specific gravity alloy with Zr and Ti combined addition

Dong-Guang Liu et al.

Summary: The (Zr, Ti)-doped W/Cu/Ni-based composite showed a completely compact structure and uniform element distribution after sintering, resulting in superior microhardness and improved electrical conductivity. The addition of Zr and Ti also decreased the mass loss of electric ablation, making these alloys promising for future electrical contact materials in electrical and electronic fields.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Homogeneous arc ablation behaviors of CuCr cathodes improved by chromic oxide

Weimian Guan et al.

Summary: The study found that CuCr50 cathodes have the lowest ablation rate, improved homogeneity, and a protective chromic oxide layer. The results provide direction for designing composite cathodes with an anti-ablation surface layer and a good conductive matrix.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

A novel approach to fabricate W-Cu functionally graded materials via sedimentation and infiltration method

Bangzheng Wei et al.

Summary: In this study, W-Cu functionally graded materials with continuously gradient distribution of W (Cu) composition and microstructure were fabricated using a novel method of sedimentation and melt-infiltration. The addition of an appropriate amount of PVB in the suspension was found to expand the gradient distribution range of W-Cu FGMs. The results show that the prepared W-Cu FGMs exhibit excellent performance in terms of hardness, density, thermal conductivity, and electrical conductivity.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Chemistry, Physical

Arc ablation behavior and microstructure evolution of plastically deformed and micro-alloyed Cu-Cr-Zr alloys

Kai Zhou et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

添加到收藏夹

Article Chemistry, Physical

Optical, structural and phase transition properties of Cu2O, CuO and Cu2O/CuO: Their photoelectrochemical sensor applications

Meral Balik et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

Arc erosion behavior of the Al2O3-Cu/(W, Cr) electrical contacts

Xiaohui Zhang et al.

COMPOSITES PART B-ENGINEERING (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Preparation and properties of ultrafine-grained W-Cu composites reinforced with tungsten fibers

Longchao Zhuo et al.

MATERIALS LETTERS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fully dense and crack free molybdenum manufactured by Selective Laser Melting through alloying with carbon

L. Kaserer et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Growth of Nb2O5 film using hydrothermal method: effect of Nb concentration on physical properties

Evan T. Salim et al.

MATERIALS RESEARCH EXPRESS (2019)

添加到收藏夹

Article Nuclear Science & Technology

High-temperature defect recovery in self-ion irradiated W-5 wt% Ta

Xiaoou Yi et al.

NUCLEAR MATERIALS AND ENERGY (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

On the nucleation mechanism of {112} ⟨111⟩ mechanical twins in as-quenched β metastable Ti-12 wt.% Mo alloy

M. Marteleur et al.

MATERIALIA (2019)

添加到收藏夹

Article Engineering, Multidisciplinary

A heat treatable TiB2/Al-3.5Cu-1.5Mg-1Si composite fabricated by selective laser melting: Microstructure, heat treatment and mechanical properties

P. Wang et al.

COMPOSITES PART B-ENGINEERING (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of process parameters on the Selective Laser Melting (SLM) of tungsten

Ravi K. Enneti et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

A novel approach to fabricate W/Cu functionally gradient materials

XinXing Ma et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2018)

添加到收藏夹

Article Chemistry, Physical

Investigation on arc erosion behaviors and mechanism of W70Cu30 electrical contact materials adding graphene

Longlong Dong et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Contact Resistance and Arc Erosion of Tungsten-copper Contacts in Direct Currents

Ma Douqin et al.

JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION (2017)

添加到收藏夹

Article Nanoscience & Nanotechnology

Atomistic simulation study of deformation twinning of nanocrystalline body-centered cubic Mo

Xiaofeng Tian et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

添加到收藏夹

Article Physics, Fluids & Plasmas

Overview of the present progress and activities on the CFETR

Yuanxi Wan et al.

NUCLEAR FUSION (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Improvement in the oxidation resistance of Nb-Si based alloy by selective laser melting

Yueling Guo et al.

CORROSION SCIENCE (2017)

添加到收藏夹

Article Engineering, Electrical & Electronic

Investigation and analysis of arc ablation on WCu electrical contact materials

Wenge Chen et al.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS (2016)

添加到收藏夹

Article Chemistry, Physical

In Situ Raman Spectroscopy of Copper and Copper Oxide Surfaces during Electrochemical Oxygen Evolution Reaction: Identification of CuIII Oxides as Catalytically Active Species

Yilin Deng et al.

ACS CATALYSIS (2016)

添加到收藏夹

Article Materials Science, Coatings & Films

Thermal Shock and Ablation Behavior of Tungsten Nozzle Produced by Plasma Spray Forming and Hot Isostatic Pressing

Y. M. Wang et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Infiltrated W-Cu composites with combined architecture of hierarchical particulate tungsten and tungsten fibers

Shuhua Liang et al.

MATERIALS CHARACTERIZATION (2015)

添加到收藏夹

Review Physics, Fluids & Plasmas

A review on two previous divertor target concepts for DEMO: mutual impact between structural design requirements and materials performance

Jeong-Ha You

NUCLEAR FUSION (2015)

添加到收藏夹

Article Physics, Applied

Raman spectroscopy of copper oxide films deposited by reactive magnetron sputtering

V. S. Levitskii et al.

TECHNICAL PHYSICS LETTERS (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

Fabrication of W-Cu functionally graded material by spark plasma sintering method

Xiaoqiao Tang et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Preparation of tungsten fiber reinforced-tungsten/copper composite for plasma facing component

Gang He et al.

JOURNAL OF NUCLEAR MATERIALS (2014)

添加到收藏夹

Article Materials Science, Ceramics

Microstructure and ablation mechanism of C/C-SiC composites

Yuanyuan Cui et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2014)

添加到收藏夹

Article Chemistry, Multidisciplinary

Surface-enhanced Raman scattering spectra of adsorbates on Cu2O nanospheres: charge-transfer and electromagnetic enhancement

Li Jiang et al.

NANOSCALE (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of HIP temperature on microstructure and low cycle fatigue strength of CuCrZr alloy

Hiroshi Nishi et al.

JOURNAL OF NUCLEAR MATERIALS (2011)

添加到收藏夹

Article Nuclear Science & Technology

High heat flux components-Readiness to proceed from near term fusion systems to power plants

A. R. Raffray et al.

FUSION ENGINEERING AND DESIGN (2010)

添加到收藏夹

Article Materials Science, Composites

Fabrication of W-Cu functionally graded materials with high density by particle size adjustment and solid state hot press

Bin-Bin Liu et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2008)

添加到收藏夹

Article Nanoscience & Nanotechnology

Strengthening mechanisms in nanocrystalline alloys

R. O. Scattergood et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

添加到收藏夹

Article Materials Science, Multidisciplinary

Manufacturing and testing W/Cu functionally graded material mock-ups for plasma facing components

Wei-Ping Shen et al.

JOURNAL OF NUCLEAR MATERIALS (2007)

添加到收藏夹

Article Materials Science, Multidisciplinary

Performance of W/Cu FGM based plasma facing components under high heat load test

Zhang-Jian Zhou et al.

JOURNAL OF NUCLEAR MATERIALS (2007)

添加到收藏夹

Review Materials Science, Coatings & Films

Thermal spray coatings for fusion applications - Review

Jiri Matejicek et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2007)

添加到收藏夹

Article Engineering, Manufacturing

Investigation on erosion of Cu/W contacts in high-voltage circuit breakers

Jens Tepper et al.

IEEE TRANSACTIONS ON COMPONENTS AND PACKAGING TECHNOLOGIES (2006)

添加到收藏夹

Article Materials Science, Multidisciplinary

Arc erosion behavior of a nanocomposite W-Cu electrical contact material

W Chen et al.

RARE METALS (2006)

添加到收藏夹

Article Engineering, Electrical & Electronic

Synthesis and characterization of one-dimensional WO2 nanorods

YR Ma et al.

JOURNAL OF VACUUM SCIENCE & TECHNOLOGY B (2005)

添加到收藏夹

Article Chemistry, Inorganic & Nuclear

Investigations of nonstoichiometric tungsten oxide nanoparticles

GL Frey et al.

JOURNAL OF SOLID STATE CHEMISTRY (2001)

添加到收藏夹

Article Electrochemistry

Infrared and Raman spectroscopy of WO3 and CdWO4

J Gabrusenoks et al.

ELECTROCHIMICA ACTA (2001)

添加到收藏夹

Article Materials Science, Multidisciplinary

Shock-induced deformation twinning and omega transformation in tantalum and tantalum-tungsten alloys

LM Hsiung et al.

ACTA MATERIALIA (2000)

添加到收藏夹

Article Materials Science, Multidisciplinary

Modifications to the microstructural topology in f.c.c. materials through thermomechanical processing

M Kumar et al.

ACTA MATERIALIA (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.