☆ 4.6 Article

Design and Optimization of Gas-Liquid Vortex Unit Using Computational Fluid Dynamics (CFD) Simulation

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Chemical

Experimental and numerical study of a compact inline swirler for gas-liquid separation

Francesco Maluta et al.

Summary: The study experimentally measured the liquid mean and fluctuating velocity field, pressure drop, gas-phase distribution, and bubble size distribution in a compact inline swirler for gas-liquid separation, validating the proposed computational approach. It was found that a coupled solution of the Population Balance Equation (PBE) with the flow equations can realistically predict the gas accumulation zone distribution.

CHEMICAL ENGINEERING SCIENCE (2023)

添加到收藏夹

Article Engineering, Chemical

Chemisorption of CO2 in a gas-liquid vortex reactor: An interphase mass transfer efficiency assessment

Yi Ouyang et al.

Summary: The capabilities of a gas-liquid vortex reactor (GLVR) as novel process intensification equipment were evaluated and found to have the ability to generate large interfacial area in a small reactor volume, resulting in superior mass transfer efficiency and energetic efficiency.

AICHE JOURNAL (2022)

添加到收藏夹

Article Engineering, Chemical

Modeling of gas-liquid flow in a rotating packed bed using an Eulerian multi-fluid approach

Wei Zhang et al.

Summary: This article proposes an Eulerian multi-fluid approach to simulate the gas-liquid flow in rotating packed beds (RPBs). Three new multiphase drag force models are constructed based on single-phase drag force models for wire mesh packings. The predicted results using the new simulation framework with the new drag force models show good agreement with the experimental data, which demonstrates the effectiveness of the proposed approach.

AICHE JOURNAL (2022)

添加到收藏夹

Article Engineering, Environmental

3D CFD simulation of the liquid flow in a rotating packed bed with structured wire mesh packing

Wei Zhang et al.

Summary: This study conducted a CFD simulation to investigate the liquid flow characteristics in rotating packed beds, revealing new flow patterns and liquid disintegration modes. The impact of contact angle and rotational speed on characteristic parameters, as well as the interfacial areas between different phases, were analyzed. The wetted packing surface area was found to be always less than the gas-liquid interfacial area, with varying ratios influenced by contact angle, rotational speed, and liquid viscosity.

CHEMICAL ENGINEERING JOURNAL (2022)

添加到收藏夹

Article Engineering, Environmental

Direct and precise determination of volumetric mass transfer coefficient of carbon monoxide for miniaturized gas-liquid reactors via sensitive probing of raman transitions

Keumrai Whang et al.

Summary: This study reports the direct and precise determination of the volumetric mass transfer coefficient of CO in miniaturized gas-liquid reactors, revealing that the values in miniaturized reactors are significantly lower than those in large-scale reactors and are more sensitive to changes in temperature and flow rate. The method used in this study has the potential to impact CO gas conversion processes, from reactor design and scale-up to process optimization and high-throughput screening of strains or catalysts.

CHEMICAL ENGINEERING JOURNAL (2022)

添加到收藏夹

Article Engineering, Chemical

Flow patterns, liquid holdup, and wetting behavior of viscous liquids in a disk-distributor rotating packed bed

Yan-Bin Li et al.

Summary: A novel disk-distributor rotating packed bed (DRPB) was developed in this study to enhance the application of RPBs in high-viscosity processes. The DRPB uses a rotating disk as a liquid distributor and porous packing to disperse the incoming high-viscosity liquid, enabling continuous flow of the liquid.

CHEMICAL ENGINEERING SCIENCE (2022)

添加到收藏夹

Article Engineering, Chemical

Experimental and Numerical Investigations on Gas Injection-Enhanced Air Gap Membrane Distillation for Water Desalination

Yanqiu Pan et al.

Summary: Gas-liquid two-phase flow enhanced air gap membrane distillation (AGMD) was investigated experimentally and numerically for water desalination. The results showed that the gas injection-enhanced AGMD can significantly increase the freshwater permeate flux. The numerical simulation results were in good agreement with the experimental results, confirming the effectiveness of gas-liquid two-phase flow enhanced AGMD.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

CFD-PBM Simulation on Bubble Size Distribution in a Gas-Liquid-Solid Flow Three-Phase Flow Stirred Tank

Shuai Li et al.

Summary: The distribution and gas holdup of bubbles in a gas-liquid-solid flow three-phase stirred tank were numerically simulated. The simulation results showed that there were differences in the fluid morphology and gas dispersion characteristics under different rotating speeds. Small-diameter bubbles were mainly concentrated in areas with higher speeds, while large-diameter bubbles existed mainly in areas with low hydrostatic pressure.

ACS OMEGA (2022)

添加到收藏夹

Article Engineering, Chemical

Two-Phase flow characterization of a rotating packed bed through CFD simulation in OpenFOAM

Roshanak Rabiee et al.

Summary: Computational fluid dynamics (CFD) simulation is an effective tool for studying the flow characteristics of a rotating packed bed (RPB), particularly in large-scale and 3D simulations. The Euler-Euler model is a reliable choice for describing the two-phase flow behavior of RPBs, with its low computational cost and sensitivity to mesh resolution. This study develops a new Euler-Euler model in OpenFOAM to characterize the two-phase flow behavior of RPBs, which is verified and validated using experimental data. The new model demonstrates promising capabilities in accurately predicting hydrodynamic parameters of RPBs.

CHEMICAL ENGINEERING SCIENCE (2022)

添加到收藏夹

Article Engineering, Chemical

Modelling of 3D liquid dispersion in a rotating packed bed using an Eulerian porous medium approach

Guojun Zhang et al.

Summary: The importance of liquid dispersion in the modeling and simulation of a rotating packed bed is discussed. A 3D Eulerian porous medium model is proposed, and the parameters used in the model are analyzed. The results show that capillary pressure and mechanical dispersion forces have a clear and significant impact on the liquid flow distribution and holdup in the packed bed.

CHEMICAL ENGINEERING SCIENCE (2022)

添加到收藏夹

Article Engineering, Chemical

A CFD-PBM Coupled Method to Optimize a Pilot-Scale Stirred Bioreactor

Hao Chen et al.

Summary: This study investigated the impact of blade structure and operating conditions on the performance of a stirred bioreactor using the PBM model and CFD method, finding that optimizing the blade structure can improve mixing performance and reduce energy consumption.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2022)

添加到收藏夹

Article Green & Sustainable Science & Technology

Renewable energy and climate change

A. G. Olabi et al.

Summary: This editorial summarized some scientific works presented at the 2018 SEEP conference, which were directly related to the scope of the RSER journal. It focused on the development of renewable energy and its positive effect on climate change, and briefly summarized the accepted manuscripts in this issue.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2022)

添加到收藏夹

Article Energy & Fuels

Structure optimization of an internal circulation rotating packed bed for the circulation liquid flow improvement: Numerical study

Lin-Xin Su et al.

Summary: This study improves the circulation liquid flow of the internal circulation rotating packed bed (IN-RPB) through structure optimization. The reliability of simulation results is verified by numerical simulation and experimental results, and the optimal structure of lifter and baffle are selected to enhance the circulation liquid flow.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2022)

添加到收藏夹

Article Energy & Fuels

Development of intensified reactors: A process intensification methodology perspective

Yi Ouyang et al.

Summary: The use of intensified equipment in the chemical industry faces obstacles. This paper proposes a methodology perspective based on coupling lab experiments, simulations, and assessment to accelerate process intensification technology.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2022)

添加到收藏夹

Article Engineering, Environmental

CFD analysis on hydrodynamics and residence time distribution in a gas-liquid vortex unit

Siyuan Chen et al.

Summary: In this study, a computational fluid dynamics (CFD) Euler-Euler model is developed to investigate the hydrodynamics and residence time distribution in a gas-liquid vortex unit (GLVU). The results show that the liquid layer rotation in the vortex chamber suppresses the gas phase vortex flow. Near the gas injection slots, the flow behavior is similar to a continuous stirred tank reactor (CSTR), leading to improved mixing and mass transfer efficiency.

CHEMICAL ENGINEERING JOURNAL (2022)

添加到收藏夹

Article Engineering, Chemical

HiGee Microbubble Generator: (I) Mathematical Modeling and Experimental Verification of the Energy Dissipation Rate

Lan Jiang et al.

Summary: This study proposed a high-gravity (HiGee) microbubble generator (HMG) and established a mathematical model for the energy dissipation rate (e) of HMG. Experimental results showed that controllable e could be achieved by controlling the rotational speed, which effectively enhanced gas-liquid mass transfer.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2022)

添加到收藏夹

Article Mechanics

Research on performance optimization of gas-liquid ejector in multiphase mixed transportation device

Junyou Zhao et al.

Summary: This study investigates the effects of outlet pressure, ratio of throat inlet area to nozzle outlet area, and nozzle contraction angle on the ejection performance of a gas-liquid ejector in the process of oil and gas extraction. Experimental and computational fluid dynamics methods were used, and the findings provide important insights for improving the efficiency of gas-liquid mixture transport.

JOURNAL OF MECHANICS (2022)

添加到收藏夹

Article Chemistry, Multidisciplinary

CFD-PBM Simulation on Bubble Size Distribution in a Gas-Liquid-Solid Flow Three-Phase Flow Stirred Tank

Shuai Li et al.

Summary: The article numerically simulated the bubble size distribution, location distribution, and gas holdup in a gas-liquid-solid flow three-phase stirred tank and found differences in fluid morphology and gas dispersion characteristics under different rotating speeds.

ACS OMEGA (2022)

添加到收藏夹

Article Engineering, Chemical

Simulation of the hydrodynamics and mass transfer in a falling film wavy microchannel

Siyuan Chen et al.

Summary: Research shows that the liquid falling film in wavy microchannels exhibits waveform distribution, which enhances gas-liquid mass transfer, especially through the formation of internal eddy flow. Compared to flat microchannels, the CO2 absorption efficiency in water in wavy microchannels is improved by over 41%.

CHINESE JOURNAL OF CHEMICAL ENGINEERING (2021)

添加到收藏夹

Article Engineering, Environmental

Eulerian simulations of liquid distribution generated by chimney and bubble cap distributors

Ekta Jain et al.

Summary: A computational model was developed to simulate gas-liquid flow in a distributor unit and validated through experiments. The study found that the type of liquid distributor affects liquid discharge pattern, flow uniformity, and pressure drop.

CHEMICAL ENGINEERING JOURNAL (2021)

添加到收藏夹

Article Engineering, Chemical

Liquid hydrodynamics in a gas-liquid vortex reactor

Yi Ouyang et al.

Summary: The gas-liquid hydrodynamics in a gas-liquid vortex reactor (GLVR) have been investigated by high-speed imaging and digital image analysis, revealing that a high turbulent kinetic energy dissipation rate contributes to a high mixing and mass transfer efficiency in the GLVR.

CHEMICAL ENGINEERING SCIENCE (2021)

添加到收藏夹

Article Engineering, Chemical

A novel slit-less gas-solid vortex reactor dryer: Experimental validation and scale-up

Pavitra Singh et al.

Summary: The SL-GSVR vortex reactor shows high heat and mass transfer efficiency, making it suitable for pharmaceutical and food processing industries, especially in food grain drying and preservation. Comparison between numerical and experimental results indicates improved bed uniformity, reduced system cost and complexity, as well as enhanced product quality in the SL-GSVR reactor.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2021)

添加到收藏夹

Article Engineering, Chemical

Micromixing in a gas-liquid vortex reactor

Yi Ouyang et al.

Summary: The gas-liquid vortex reactor shows great potential in intensifying micromixing processes for multiphase reactions. Introducing liquid into the reactor suppresses gas flow, and factors affecting micromixing efficiency include gas flow rate, liquid flow rate, and liquid viscosity. The micromixing time of the GLVR is determined to be comparable to a rotating packed bed and superior to a static mixer.

AICHE JOURNAL (2021)

添加到收藏夹

Article Energy & Fuels

CFD-based assessment of steady-state multiplicity in a gas-solid vortex reactor for oxidative coupling of methane

Laurien A. Vandewalle et al.

Summary: The research indicates that GSVR reactors may meet the intensified conditions for OCM, with limited species backmixing and sufficient thermal backmixing. Adiabatic simulations show promising performance in terms of outlet temperature, conversions, and selectivities.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2021)

添加到收藏夹

Article Engineering, Environmental

Regulation of gas-liquid Taylor flow by pulsating gas intake in micro-channel

Yaheng Zhang et al.

Summary: Bubble formation mechanism and slug flow characteristics in a T-junction rectangular micro-channel under pulsating gas intake conditions were studied through experimental and numerical simulation. Under pulsating gas intake conditions, the bubble length is shorter, the liquid slug length is longer, and the bubble velocity varies periodically over time, transforming into wave flow when the pulsation energy reaches a critical value.

CHEMICAL ENGINEERING JOURNAL (2021)

添加到收藏夹

Article Engineering, Chemical

On the Volume of Fluid Simulation Details and Droplet Size Distribution inside Rotating Packed Beds

Shahab Golshan et al.

Summary: The research utilizes the VOF method to study the hydrodynamics of RPBs and finds different radial trends of droplet diameter at various rotational speeds in the packing region, explaining the observed phenomena.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2021)

添加到收藏夹

Article Engineering, Environmental

Simulation and multi-objective optimization of a radial flow gas-cooled membrane reactor, considering reduction of CO2 emissions in methanol synthesis

Z. Dehghani et al.

Summary: This paper investigates the effectiveness of gas-cooled reactors and gas-cooled membrane reactors in removing CO2 during methanol synthesis, with optimized RF-GCMR showing significant improvements in CO2 removal rate and methanol production.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2021)

添加到收藏夹

Article Engineering, Environmental

Intensification on mass transfer between gas and liquid in fine bubble jet reactor

Baorong Wang et al.

Summary: Fine Bubble Jet reactor (FBJR) is designed to enhance gas-liquid mass transfer through the generation of fine bubbles. The study evaluated the mass transfer and hydrodynamic characteristics of FBJR, showing that it can efficiently capture CO2 with high removal efficiency compared to other reactors.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2021)

添加到收藏夹

Article Engineering, Environmental

CFD simulation of gas-liquid flow in stirred tanks: Effect of drag models

Xiaoping Guan et al.

CHEMICAL ENGINEERING JOURNAL (2020)

添加到收藏夹

Article Engineering, Environmental

Liquid flow behavior in a multiliquid-inlet rotating packed bed reactor with three-dimensional printed packing

Wei Wu et al.

CHEMICAL ENGINEERING JOURNAL (2020)

添加到收藏夹

Article Chemistry, Multidisciplinary

Developing Intelligent Algorithm as a Machine Learning Overview over the Big Data Generated by Euler-Euler Method To Simulate Bubble Column Reactor Hydrodynamics

Meisam Babanezhad et al.

ACS OMEGA (2020)

添加到收藏夹

Article Energy & Fuels

CFD analysis of the hydrodynamic characteristics in a rotating packed bed with multi-nozzles

Wei Zhang et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2020)

添加到收藏夹

Article Thermodynamics

Hydrodynamics of the vortex tray

Nina Deryagina et al.

THERMAL SCIENCE AND ENGINEERING PROGRESS (2020)

添加到收藏夹

Article Thermodynamics

Numerical simulations of the effect of liquid viscosity on gas-liquid mass transfer of a bubble column with a CFD-PBM coupled model

Huahai Zhang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

添加到收藏夹

Article Engineering, Chemical

The role of mass and heat transfer in the design of novel reactors for oxidative coupling of methane

Laurien A. Vandewalle et al.

CHEMICAL ENGINEERING SCIENCE (2019)

添加到收藏夹

Article Engineering, Chemical

CFD Simulation and High-Speed Photography of Liquid Flow in the Outer Cavity Zone of a Rotating Packed Bed Reactor

Yi Liu et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2019)

添加到收藏夹

Article Engineering, Chemical

Investigation of bubble plume oscillations by Euler-Euler simulation

Sebastian Fleck et al.

CHEMICAL ENGINEERING SCIENCE (2019)

添加到收藏夹

Article Energy & Fuels

Global hydrodynamic of hybrid external loop airlift reactor: Experiments and CFD modelling

Nacereddine Moudoud et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2018)

添加到收藏夹

Article Engineering, Chemical

Bubbly flow in stirred tanks: Euler-Euler/RANS modeling

Pengyu Shi et al.

CHEMICAL ENGINEERING SCIENCE (2018)

添加到收藏夹

Article Energy & Fuels

Computational Fluid Dynamics-Assisted Process Intensification Study for Biomass Fast Pyrolysis in a Gas-Solid Vortex Reactor

Shekhar R. Kulkarni et al.

ENERGY & FUELS (2018)

添加到收藏夹

Article Engineering, Chemical

Computational Fluid Dynamics Simulations of the Air-Water Two-Phase Vertically Upward Bubbly Flow in Pipes

Dhiraj A. Lote et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2018)

添加到收藏夹

Article Nuclear Science & Technology

CFD studies on the gas-liquid flow in the swirl generating device

Ryan Anugrah Putra et al.

NUCLEAR ENGINEERING AND DESIGN (2018)

添加到收藏夹

Article Energy & Fuels

Mass-Transfer Performance for CO2 Absorption by 2-(2-Aminoethylamino)ethanol Solution in a Rotating Packed Bed

Shuying Wu et al.

ENERGY & FUELS (2017)

添加到收藏夹

Article Engineering, Chemical

Three-Dimensional Simulation on Liquid Flow in a Rotating Packed Bed Reactor

Tian-Yu Guo et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2017)

添加到收藏夹

Article Engineering, Environmental

CFD optimization of the baffle angle of an expanded granular sludge bed reactor

Yi Fan Hu et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2017)

添加到收藏夹

Article Engineering, Chemical

Characteristics of liquid flow in a rotating packed bed for CO2 capture: A CFD analysis

Peng Xie et al.

CHEMICAL ENGINEERING SCIENCE (2017)

添加到收藏夹

Article Engineering, Environmental

Design and cold flow testing of a Gas-Solid Vortex Reactor demonstration unit for biomass fast pyrolysis

Arturo Gonzalez-Quiroga et al.

CHEMICAL ENGINEERING JOURNAL (2017)

添加到收藏夹

Article Engineering, Chemical

Experimental study of paddy drying in a vortex chamber

Jnyana Ranjan Pati et al.

DRYING TECHNOLOGY (2016)

添加到收藏夹

Article Computer Science, Interdisciplinary Applications

Optimal industrial reactor design: development of a multiobjective optimization method based on a posteriori performance parameters calculated from CFD flow solutions

Jonas Laerte Ansoni et al.

ADVANCES IN ENGINEERING SOFTWARE (2016)

添加到收藏夹

Review Green & Sustainable Science & Technology

Process, performance and modeling of CO2 capture by chemical absorption using high gravity: A review

Bingtao Zhao et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2016)

添加到收藏夹

Review Energy & Fuels

Process intensification for post-combustion CO2 capture with chemical absorption: A critical review

Meihong Wang et al.

APPLIED ENERGY (2015)

添加到收藏夹

Article Engineering, Chemical

Key Parameter Prediction and Validation for a Pilot-Scale Rotating-Disk Contactor by CFD-PBM Simulation

Hang Chen et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2014)

添加到收藏夹

Article Agriculture, Multidisciplinary

Advances in the use of CFD to characterize, design and optimize bioenergy systems

Binxin Wu

COMPUTERS AND ELECTRONICS IN AGRICULTURE (2013)

添加到收藏夹

Article Engineering, Chemical

Phenomena Based Methodology for Process Synthesis Incorporating Process Intensification

Philip Lutze et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2013)

添加到收藏夹

Article Engineering, Chemical

Mass transfer in gas-liquid layer on vortex contact stages

N. A. Voinov et al.

THEORETICAL FOUNDATIONS OF CHEMICAL ENGINEERING (2013)

添加到收藏夹

Article Engineering, Aerospace

Investigation of the flow in the vortex chamber with centrifugal fluidizing bed with and without combustion

E. P. Volchkov et al.

THERMOPHYSICS AND AEROMECHANICS (2013)

添加到收藏夹

Article Engineering, Chemical

Multistage Rotor-Stator Spinning Disc Reactor

Marco Meeuwse et al.

AICHE JOURNAL (2012)

添加到收藏夹

Article Engineering, Chemical

Fluid catalytic cracking in a rotating fluidized bed in a static geometry: a CFD analysis accounting for the distribution of the catalyst coke content

Waldo Rosales Trujillo et al.

POWDER TECHNOLOGY (2012)

添加到收藏夹

Article Engineering, Chemical

Hydrodynamics of the vortex stage with tangential swirlers

N. A. Voinov et al.

THEORETICAL FOUNDATIONS OF CHEMICAL ENGINEERING (2010)

添加到收藏夹

Review Environmental Sciences

Global warming and carbon dioxide through sciences

Georgios A. Florides et al.

ENVIRONMENT INTERNATIONAL (2009)

添加到收藏夹

Article Engineering, Chemical

Modelling and simulation of gas-liquid hydrodynamics in mechanically stirred tanks

F. Scargiali et al.

CHEMICAL ENGINEERING RESEARCH & DESIGN (2007)

添加到收藏夹

Article Engineering, Chemical

Numerical simulation of the dynamic flow behavior in a bubble column: A study of closures for turbulence and interface forces

D. Zhang et al.

CHEMICAL ENGINEERING SCIENCE (2006)

添加到收藏夹

Article Mechanics

A two-equation turbulence model of turbulent bubbly flows

AA Troshko et al.

INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2001)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.