☆ 4.7 Article

CFD-DEM investigation on the agglomeration behavior of micron-sized combusted iron fines

FUEL (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Chemical

Regeneration of iron fuel in fluidized beds Part II: Reduction experiments

X. Liu et al.

Summary: Direct reduction of combusted iron powders using renewable energy is crucial for a carbon-neutral iron fuel cycle. Lab-scale reduction experiments show that a temperature of 500 degrees C achieves a reduction degree higher than 90%, while higher temperatures result in particle sintering and lower reduction degree due to quick defluidization. The study highlights the significance of temperature on sintering and reduction behavior, with negligible impact from gas velocity. The findings offer insights for the design of hydrogen-based iron fuel regeneration processes.

POWDER TECHNOLOGY (2023)

添加到收藏夹

Article Engineering, Chemical

Regeneration of iron fuel in fluidized beds, Part I: Defluidization experiments and theoretical prediction model

X. Liu et al.

Summary: Hydrogen-based direct reduction of iron oxide powder in gas-fluidized beds is a developing technology, but the agglomeration of fine powder at high temperatures is a key issue. This study experimentally investigates the (de-)fluidization behavior of micron-sized combusted iron particles to understand the high-temperature agglomeration mechanism. The effects of various operating and material variables on the fluidization and agglomeration behavior are examined, and a theoretical model is developed to predict the boundaries of fluidization regimes. The obtained knowledge is then applied for experimental design of the hydrogen-based iron direct reduction process.

POWDER TECHNOLOGY (2023)

添加到收藏夹

Article Thermodynamics

Combustion of Iron Particles Suspension in Laminar Premixed and Diffusion Flames

N. Poletaev et al.

Summary: This study investigates the combustion regimes of iron particles in a premixed flame and a diffusion flame. It is found that under certain conditions, the iron particles in the premixed flame can switch to a high-temperature diffusion mode of combustion, while this mode is not observed in the diffusion flame. In addition, gas-phase reactions are intensified, leading to an increase in the mass yield of nanoscale particles in the combustion products.

COMBUSTION SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Thermodynamics

Temperature and phase transitions of laser-ignited single iron particle

Daoguan Ning et al.

Summary: The combustion behavior of single laser-ignited iron particles was investigated by measuring transient particle radiant intensities and time-resolved temperatures. A plateau-like stage shortly after ignition was repeatedly observed, identified as iron particle melting. An abrupt brightness jump near the end of combustion was observed for most particles, while some showed a second plateau-like stage. The temperature change corresponded to phase-change temperatures in the Fe-O phase diagram, explaining the presence of the brightness jump.

COMBUSTION AND FLAME (2022)

添加到收藏夹

Article Engineering, Chemical

Reduction kinetics of combusted iron powder using hydrogen

C. J. M. Hessels et al.

Summary: Hydrogen reduction of iron oxide fines produced by iron combustion was investigated using thermogravimetric analysis (TGA). The results showed that the morphology of the reduction products depended on temperature but not on the hydrogen partial pressure, with higher temperatures leading to larger pore sizes. Based on analysis, the reduction process could be described by a single-step phase boundary controlled reaction at temperatures below 600℃, and a multi-step mechanism was required for reactions at higher temperatures.

POWDER TECHNOLOGY (2022)

添加到收藏夹

Article Energy & Fuels

Iron dust explosion characteristics with small amount of nano-sized Fe2O3 and Fe3O4 particles

Yongzheng Guo et al.

Summary: Iron powder is a promising alternative to fossil fuels in a low-carbon economy. The explosion characteristics of iron dust were studied, and adding small amounts of iron oxides can reduce the explosion severity and sensitivity of iron dust. The addition of 5% oxide has an obvious inhibition effect, and increasing the oxide concentration to 10% further increases the inerting effect. However, increasing dust concentration weakens the inhibiting effect. The MEC data determined by different methods are comparable.

FUEL (2022)

添加到收藏夹

Article Engineering, Chemical

On the treatment of bed-to-wall heat transfer in CFD-DEM simulations of gas-fluidized beds

Xin Liu et al.

Summary: The study investigates the heat transfer mechanism near the confining walls in fluidized beds using two approaches, validating them with experimental results and comparing their performance in predicting overall particle temperature distribution, parameter sensitivity, and mesh resolution.

CHEMICAL ENGINEERING SCIENCE (2021)

添加到收藏夹

Article Engineering, Chemical

Coarse graining Euler-Lagrange simulations of cohesive particle fluidization

Josef Tausendschoen et al.

POWDER TECHNOLOGY (2020)

添加到收藏夹

Article Engineering, Chemical

On the scaling law of JKR contact model for coarse-grained cohesive particles

Xizhong Chen et al.

CHEMICAL ENGINEERING SCIENCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Morphology of Iron and Agglomeration Behaviour During Reduction of Iron Oxide Fines

Muhammad Irfan Ahadian Barustan et al.

METALS AND MATERIALS INTERNATIONAL (2019)

添加到收藏夹

Review Thermodynamics

Recyclable metal fuels for clean and compact zero-carbon power

Jeffrey M. Bergthorson

PROGRESS IN ENERGY AND COMBUSTION SCIENCE (2018)

添加到收藏夹

Article Energy & Fuels

The reduction kinetics of hematite particles in H2 and CO atmospheres

Jeongseog Oh et al.

FUEL (2017)

添加到收藏夹

Article Chemistry, Physical

Enabling the metal fuel economy: green recycling of metal fuels

Philippe Julien et al.

SUSTAINABLE ENERGY & FUELS (2017)

添加到收藏夹

Article Energy & Fuels

Direct combustion of recyclable metal fuels for zero-carbon heat and power

J. M. Bergthorson et al.

APPLIED ENERGY (2015)

添加到收藏夹

Article Engineering, Chemical

Investigating agglomeration phenomena in an air-polyethylene fluidized bed using DEM-CFD approach

Zahra Mansourpour et al.

CHEMICAL ENGINEERING RESEARCH & DESIGN (2014)

添加到收藏夹

Article Engineering, Chemical

Study on a large-scale discrete element model for fine particles in a fluidized bed

Mikio Sakai et al.

ADVANCED POWDER TECHNOLOGY (2012)

添加到收藏夹

Article Engineering, Chemical

Influence of rolling friction on single spout fluidized bed simulation

Christoph Goniva et al.

PARTICUOLOGY (2012)

添加到收藏夹

Article Thermodynamics

Models, algorithms and validation for opensource DEM and CFD-DEM

Christoph Kloss et al.

PROGRESS IN COMPUTATIONAL FLUID DYNAMICS (2012)

添加到收藏夹

Article Materials Science, Multidisciplinary

Mechanical properties of magnetite (Fe3O4), hematite (α-Fe2O3) and goethite (α-FeO•OH) by instrumented indentation and molecular dynamics analysis

D. Chicot et al.

MATERIALS CHEMISTRY AND PHYSICS (2011)

添加到收藏夹

Article Engineering, Chemical

Drag force of intermediate Reynolds number flow past mono- and bidisperse arrays of spheres

R. Beetstra et al.

AICHE JOURNAL (2007)

添加到收藏夹

Article Metallurgy & Metallurgical Engineering

Deformation of iron oxides upon tensile tests at 600-1250°C

Y Hidaka et al.

OXIDATION OF METALS (2003)

添加到收藏夹

Article Engineering, Chemical

Interparticle forces in fluidisation: a review

JPK Seville et al.

POWDER TECHNOLOGY (2000)

添加到收藏夹

Article Engineering, Chemical

Modelling of sintering of iron particles in high-temperature gas fluidisation

PC Knight et al.

CHEMICAL ENGINEERING SCIENCE (2000)

添加到收藏夹

Article Engineering, Chemical

Numerical simulation of metallic solid bridging particles in a fluidized bed at high temperature

K Kuwagi et al.

POWDER TECHNOLOGY (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.