☆ 4.7 Article

Cyclic behavior of unbonded post-tensioned precast segmental concrete columns fabricated by 3D printed concrete permanent formwork

ENGINEERING STRUCTURES (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Construction & Building Technology

3D Printed concrete with coarse aggregates: Built-in-Stirrup permanent concrete formwork for reinforced columns

Yidong Chen et al.

Summary: This paper investigates the axial compression performance of reinforced columns with 3D-printed permanent concrete formwork. It proposes a novel square stirrup with reserved longitudinal reinforcement holes and its built-in-stirrup permanent concrete formwork method (BSPCF). Experimental results show that columns with only 3D-printed formwork face early spalling and significant reduction in bearing capacity. Using BSPCF can effectively avoid these problems and enhance the column bearing capacity. X-ray computed tomography reveals the sudden decrease in aggregate content and increase of voids in the interface region, further emphasizing the importance of BSPCF in stress transfer.

JOURNAL OF BUILDING ENGINEERING (2023)

添加到收藏夹

Article Construction & Building Technology

Experimental study on large-scale 3D printed concrete walls under axial compression

Xiaoyu Han et al.

Summary: The study found that the failure of 3D printed concrete walls under axial compression loads is brittle, and the use of horizontal steel reinforcement reduces their ultimate bearing capacity, with the layers where the horizontal steel reinforcement is set becoming weak zones.

AUTOMATION IN CONSTRUCTION (2022)

添加到收藏夹

Article Engineering, Civil

Shaking table tests of a resilient bridge system with precast reinforced concrete columns equipped with springs

Natalia Reggiani Manzo et al.

Summary: This paper presents the shake table test results of a novel system for the design of precast reinforced concrete bridges. The system increases stability by adding a flexible restraining system and anchoring the tendon within the column, reducing foundation size. The tests showed the system's resilience but also highlighted the risk of failure in certain circumstances.

EARTHQUAKE ENGINEERING & STRUCTURAL DYNAMICS (2022)

添加到收藏夹

Article Engineering, Civil

Analytical model for evaluating lateral force capacity of precast concrete-filled steel tube column

Kaidi Zhang et al.

Summary: A non-iterative simplified analytical model was proposed in this study to predict the lateral force capacity of post-tensioned precast segmental columns. The model was validated through quasi-static tests and finite element modeling, demonstrating good agreement with experimental and numerical results. The gravity load and reinforcement ratio of prestressed tendons were found to have a significant impact on the post-yield stiffness of the columns.

ENGINEERING STRUCTURES (2022)

添加到收藏夹

Article Engineering, Civil

Experimental and numerical study on seismic performance of precast segmental CFST bridge columns with non-uniform prestressed steel tendons

Dan Zhang et al.

ENGINEERING STRUCTURES (2022)

添加到收藏夹

Article Engineering, Multidisciplinary

Fresh and anisotropic-mechanical properties of 3D printable ultra-high ductile concrete with crumb rubber

Junhong Ye et al.

Summary: A novel ultra-high ductile concrete (UHDC) modified with crumb rubber was developed for 3D concrete printing. Mechanical tests revealed that the printed UHDC had higher deformability and energy dissipation in certain directions compared to mold-cast UHDC. Additionally, minimal anisotropy was found in flexural strength, but significant anisotropy in flexural deformability, compressive strength and flexural energy dissipation capacity of the printed UHDC.

COMPOSITES PART B-ENGINEERING (2021)

添加到收藏夹

Article Engineering, Civil

Energy dissipation and resilience of precast segmented concrete-filled steel tube self-centering column: Parameter study and design methodology

Dan Zhang et al.

Summary: The testing and analysis of precast segmented concrete-filled steel-tube self-centering columns can determine the optimal design parameters for energy dissipation and resilience, optimizing and increasing the structural capacity and performance.

ENGINEERING STRUCTURES (2021)

添加到收藏夹

Article Engineering, Civil

Seismic Performance of Precast Segmental Concrete-Filled Steel-Tube Bridge Columns with Internal and External Energy Dissipaters

Dan Zhang et al.

Summary: The prefabricated segmental column using posttensioning technology has improved construction speed and environmental friendliness. The PSCFST bridge columns with internal or external ED bars can avoid damage to segment joints during seismic events and enhance energy dissipation. Through testing, it was found that PSCFST columns perform well under seismic loads, while MRC columns suffer severe damage.

JOURNAL OF BRIDGE ENGINEERING (2021)

添加到收藏夹

Article Construction & Building Technology

Uniaxial load testing of large-scale 3D-printed concrete wall and finite-element model analysis

Totsawat Daungwilailuk et al.

Summary: This study focuses on the design of load-bearing walls in 3D-printed buildings, conducting experiments on different wall samples and finite-element analysis to evaluate the behavior of the walls. Results show that the flat wall with an inner truss outperformed the diamond wall, providing a new perspective on design flexibility.

CONSTRUCTION AND BUILDING MATERIALS (2021)

添加到收藏夹

Article Construction & Building Technology

3D concrete printing of permanent formwork for concrete column construction

Binrong Zhu et al.

Summary: This study investigated the 3D concrete printing for permanent formwork in concrete column construction. By adjusting the HPMC contents and water-to-binder ratios, the study found that a specific mixture can enhance the static yield stress, green strength, and bearing capacity of the permanent formwork. Additionally, concrete columns constructed using printed concrete as permanent formwork exhibited higher stiffness and bearing capacity compared to traditional concrete columns.

CEMENT & CONCRETE COMPOSITES (2021)

添加到收藏夹

Article Engineering, Geological

A novel precast concrete beam-to-column connection with replaceable energy-dissipation connector: Experimental investigation and theoretical analysis

Chao Tong et al.

Summary: A novel precast concrete beam-to-column connection is proposed in this study to prevent damage from beam overstrength and strength hierarchy alteration. The use of replaceable energy-dissipation connectors (REDCs) and vertical slots significantly reduce additional bending moments and improve seismic performance. Finite element models further demonstrate the controllable variable nature of the bending moments in this novel connection design.

BULLETIN OF EARTHQUAKE ENGINEERING (2021)

添加到收藏夹

Article Construction & Building Technology

3D printing eco-friendly concrete containing under-utilised and waste solids as aggregates

Gang Bai et al.

Summary: 3D concrete printing technology provides an opportunity for utilising underutilised and waste solids as aggregates. The experimental study in this article shows that the self-supporting skeletal effect formed by gradated particles can improve the construction performance of mixtures and reduce the shrinkage of the cement matrix. These findings provide feasible solutions for promoting the eco-utilisation of underutilised and waste solids in 3D printing while meeting strength and durability requirements.

CEMENT & CONCRETE COMPOSITES (2021)

添加到收藏夹

Article Engineering, Civil

Structural behaviour of 3D printed concrete beams with various reinforcement strategies

Lukas Gebhard et al.

Summary: The study conducted experiments on 3DCP beams reinforced with different types of reinforcement, revealing that beams with conventional bonded longitudinal reinforcement developed bending and shear cracks, while post-tensioned beams failed in a brittle manner with interlayer shear reinforcement playing a key role.

ENGINEERING STRUCTURES (2021)

添加到收藏夹

Article Engineering, Civil

Mechanical behaviors of 3D printed lightweight concrete structure with hollow section

Li Wang et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2020)

添加到收藏夹

Article Construction & Building Technology

Mesh reinforcing method for 3D Concrete Printing

Taylor Marchment et al.

AUTOMATION IN CONSTRUCTION (2020)

添加到收藏夹

Article Construction & Building Technology

3D printing of a post-tensioned concrete girder designed by topology optimization

Gieljan Vantyghem et al.

AUTOMATION IN CONSTRUCTION (2020)

添加到收藏夹

Article Construction & Building Technology

A novel additive mortar leveraging internal curing for enhancing interlayer bonding of cementitious composite for 3D printing

Guowei Ma et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

添加到收藏夹

Article Engineering, Geological

Seismic performance of bridge with unbonded posttensioned self-centering segmented concrete-filled steel-tube columns: An underwater shaking table test

Dan Zhang et al.

SOIL DYNAMICS AND EARTHQUAKE ENGINEERING (2020)

添加到收藏夹

Article Engineering, Geological

Shake table testing of unbonded post-tensioned concrete walls with and without additional energy dissipation

K. M. Twigden et al.

SOIL DYNAMICS AND EARTHQUAKE ENGINEERING (2019)

添加到收藏夹

Article Engineering, Geological

Cyclic test and numerical study of precast segmental concrete columns with BFRP and TEED

Chao Li et al.

BULLETIN OF EARTHQUAKE ENGINEERING (2019)

添加到收藏夹

Article Engineering, Civil

Shaking Table Tests of Post-Tensioned Rocking Bridge with Double-Column Bents

Yu-Long Zhou et al.

JOURNAL OF BRIDGE ENGINEERING (2019)

添加到收藏夹

Article Engineering, Civil

Design criterion for the self-centering capacity of precast segmental UHPC bridge columns with unbonded post-tensioning tendons

Zhen Wang et al.

ENGINEERING STRUCTURES (2019)

添加到收藏夹

Article Construction & Building Technology

3D printing of reinforced concrete elements: Technology and design approach

Domenico Asprone et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

添加到收藏夹

Article Construction & Building Technology

Pseudodynamic Testing and Inelastic Displacement Ratios of Self-Centering Precast Concrete Segmental Bridge Columns

Yu-Chen Ou et al.

JOURNAL OF STRUCTURAL ENGINEERING (2018)

添加到收藏夹

Article Construction & Building Technology

Pseudodynamic Testing and Inelastic Displacement Ratios of Self-Centering Precast Concrete Segmental Bridge Columns

Yu-Chen Ou et al.

JOURNAL OF STRUCTURAL ENGINEERING (2018)

添加到收藏夹

Article Engineering, Civil

Seismic behavior of precast segmental UHPC bridge columns with replaceable external cover plates and internal dissipaters

Zhen Wang et al.

ENGINEERING STRUCTURES (2018)

添加到收藏夹

Article Engineering, Manufacturing

Design of a 3D printed concrete bridge by testing

Theo A. M. Salet et al.

VIRTUAL AND PHYSICAL PROTOTYPING (2018)

添加到收藏夹

Article Construction & Building Technology

Ultrahigh-Performance Concrete for Posttensioned Precast Bridge Piers for Seismic Resilience

Cancan Yang et al.

JOURNAL OF STRUCTURAL ENGINEERING (2017)

添加到收藏夹

Article Construction & Building Technology

Ultrahigh-Performance Concrete for Posttensioned Precast Bridge Piers for Seismic Resilience

Cancan Yang et al.

JOURNAL OF STRUCTURAL ENGINEERING (2017)

添加到收藏夹

Article Engineering, Civil

Seismic Performance of Precast, Pretensioned, and Cast-in-Place Bridges: Shake Table Test Comparison

Islam M. Mantawy et al.

JOURNAL OF BRIDGE ENGINEERING (2016)

添加到收藏夹

Article Construction & Building Technology

Cyclic Load Tests on Self-Centering Concrete Pier with External Dissipators and Enhanced Durability

Tong Guo et al.

JOURNAL OF STRUCTURAL ENGINEERING (2016)

添加到收藏夹

Article Construction & Building Technology

Cyclic Load Tests on Self-Centering Concrete Pier with External Dissipators and Enhanced Durability

Tong Guo et al.

JOURNAL OF STRUCTURAL ENGINEERING (2016)

添加到收藏夹

Article Construction & Building Technology

Seismic Performance of Segmental Rocking Columns Connected with NiTi Martensitic SMA Bars

Do Young Moon et al.

ADVANCES IN STRUCTURAL ENGINEERING (2015)

添加到收藏夹

Article Mechanics

Mechanical behavior of FRP sheets reinforced 3D elements printed with cementitious materials

Peng Feng et al.

COMPOSITE STRUCTURES (2015)

添加到收藏夹

Article Construction & Building Technology

Mechanical properties of structures 3D printed with cementitious powders

Peng Feng et al.

CONSTRUCTION AND BUILDING MATERIALS (2015)

添加到收藏夹

Article Construction & Building Technology

Seismic Behavior of Posttensioned Self-Centering Precast Concrete Dual-Shell Steel Columns

Gabriele Guerrini et al.

JOURNAL OF STRUCTURAL ENGINEERING (2015)

添加到收藏夹

Article Construction & Building Technology

Seismic Behavior of Posttensioned Self-Centering Precast Concrete Dual-Shell Steel Columns

Gabriele Guerrini et al.

JOURNAL OF STRUCTURAL ENGINEERING (2015)

添加到收藏夹

Article Engineering, Civil

Seismic Behavior of Posttensioned Concrete-Filled Fiber Tubes

Mohamed ElGawady et al.

JOURNAL OF COMPOSITES FOR CONSTRUCTION (2010)

添加到收藏夹

Article Engineering, Civil

Large-scale seismic tests of tall concrete bridge columns with precast segmental construction

Jui-Chen Wang et al.

EARTHQUAKE ENGINEERING & STRUCTURAL DYNAMICS (2008)

添加到收藏夹

Article Construction & Building Technology

Design, modeling, and experimental response of seismic resistant bridge piers with posttensioned dissipating connections

A. Palermo et al.

JOURNAL OF STRUCTURAL ENGINEERING (2007)

添加到收藏夹

Article Construction & Building Technology

Seismic performance of segmental precast unbonded posttensioned concrete bridge columns

Yu-Chen Ou et al.

JOURNAL OF STRUCTURAL ENGINEERING (2007)

添加到收藏夹

Article Engineering, Civil

Cyclic Response of Unbonded Posttensioned Precast Columns with Ductile Fiber-Reinforced Concrete

S. L. Billington et al.

JOURNAL OF BRIDGE ENGINEERING (2004)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.