☆ 4.7 Article

Corrosion characteristics of Inconel 625 cladding layer and NiCrMoAl cladding layer in molten NaCl-KCl and NaCl-KCl-Na2SO4

CORROSION SCIENCE (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Materials Science, Multidisciplinary

Effect of Nb content on microstructure, mechanical property, high-temperature corrosion and oxidation resistance of CrNb coatings for accident tolerant fuel cladding

Hanxuan Su et al.

Summary: Five CrNb coatings with different Nb contents were prepared on zircalloy substrate using magnetron sputtering technology. The influence of Nb content on the microstructure, mechanical properties, high-temperature corrosion, and oxidation resistance of the coatings was investigated. The results showed that increasing Nb content improved the wear performance and nanohardness of the coatings, while the corrosion resistance remained relatively unaffected. The coating with 21at% Nb content exhibited optimal mechanical and high-temperature oxidation properties.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2023)

添加到收藏夹

Article Chemistry, Physical

Evolution in microstructure and oxidation behaviors of the laser cladding C22 coatings with the Si addition concentrations

Yao Kong et al.

Summary: In this study, C22 coatings with different concentrations of Si were prepared on TP347H by laser cladding. The effect of Si on the microstructure evolution, phase constitution, and high temperature oxidation behaviors were investigated. The results showed that the addition of 3 wt% Si significantly improved the oxidation resistance of the coatings at temperatures between 600-700 degrees C.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

High temperature corrosion mechanism of Ni-5W-6B-28Cr-13Al alloy in simulated MSW incineration environment

Wenchao Ma et al.

Summary: This study investigates the corrosion behavior of a newly designed alloy (Ni-5W-6B-28Cr-13Al) in a simulated municipal solid waste incineration atmosphere containing HCl, NaCl, and SO2. The results showed that the corrosion rate was highest when NaCl and HCl were present together. The corrosion of the alloy was enhanced by the presence of NaCl and formed unprotective oxide scales, but the synergistic effect of NaCl and HCl was suppressed by sulfation after SO2 application.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Chlorine-induced high-temperature corrosion characteristics of Ni-Cr alloy cladding layer and Ni-Cr-Mo alloy cladding layer

Xinyu Wang et al.

Summary: The corrosion properties of four nickel-based cladding layers under chlorine-induced high-temperature corrosion were evaluated using the thickness loss rate. The results show that increasing the Cr content alone does not improve corrosion resistance, but instead worsens internal corrosion. The effect of Mo on enhancing corrosion resistance in laser cladding technology is closely related to its content and distribution. Transverse penetration cracks tend to occur in NiO surrounded by NiCr2O4, while the presence of short rod-like NbO2 enhances the mechanical properties of the NiO layer and eliminates such cracks.

CORROSION SCIENCE (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

316L stainless steel repaired layers by weld surfacing and laser cladding on a 27SiMn steel: A comparative study of microstructures, corrosion, hardness and wear performances

Zhihao Li et al.

Summary: In this study, 316L stainless steel repaired layers were fabricated on a 27SiMn steel substrate using weld surfacing and laser cladding techniques. The microstructures of the repaired layers were characterized, and their surface properties were measured and correlated with the microstructure features. The laser-cladding repaired layer exhibited superior corrosion and wear resistance, which can be attributed to the laser-induced ultrafast cooling and the formation of denser and finer grain structures.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot corrosion behavior of an arc sprayed Fe-based amorphous coating in a simulated biomass firing environment

Peiyuan Pan et al.

Summary: The study found that in biomass boilers, the arc sprayed Fe-Cr-Mo amorphous coating was vulnerable to chlorination with Fe and Cr elements evaporating continuously, Mo distribution being uneven, and crevices in the coating detrimental to its corrosion resistance.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Electrochemical study on the hot corrosion behavior of Ni16Cr13Co4Mo alloy in molten NaCl-KCl and NaCl-KCl-Na2SO4

J. H. Wang et al.

Summary: The hot corrosion behavior of a novel Ni16Cr13Co4Mo alloy in molten NaCl-KCl and NaClKCl-Na2SO4 was investigated. The overall corrosion process was controlled by diffusion, and the presence of Na2SO4 promoted the hot corrosion. The composition and properties of the corrosion layer differed in different molten salt environments.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

High temperature oxidation behavior of a novel Ni-Cr-W-Al-Ti superalloy

Jianwei Teng et al.

Summary: The novel high-temperature alloy demonstrates excellent oxidation resistance during the oxidation process, mainly attributed to the continuous formation of Ti-rich oxide on the external surface, inhibiting the volatilization of Cr2O3, and the fine Al2O3 particles along the grain boundaries of the alloy matrix effectively blocking the inward diffusion of oxygen and outward diffusion of chromium.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Thermodynamics

Exergoeconomic analysis and optimization of an innovative municipal solid waste to energy plant integrated with solar thermal system

Muhammad Sajid Khan et al.

Summary: Waste to energy technology is a promising method to deal with municipal solid waste, and integrating a municipal solid waste incineration plant with a solar thermal system can improve energy production efficiency. Thermodynamic and exergoeconomic analysis showed that the integrated plant had higher efficiencies and economic performance compared to traditional designs, making it a promising solution from both a thermodynamic and economic perspective.

ENERGY CONVERSION AND MANAGEMENT (2022)

添加到收藏夹

Article Optics

Selecting process parameters of crack-free Ni60A alloy coating prepared by coaxial laser cladding

Bowen Shi et al.

Summary: In this study, a crack-free Ni60A coating was successfully obtained by selecting suitable process parameters. It was found that a high line energy and low powder feed rate can prevent cracking, but result in low microhardness. Further research showed that a combination of preheating and adding an insulating plate can improve the microhardness of the crack-free coating.

OPTICS AND LASER TECHNOLOGY (2022)

添加到收藏夹

Article Green & Sustainable Science & Technology

Corrosion of heat exchanger materials in co-combustion thermal power plants

Kaiyang Li et al.

Summary: This article reviews the characteristics and corrosion behavior of co-combustion systems, and summarizes the corrosion mitigation strategies and future research directions.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2022)

添加到收藏夹

Article Materials Science, Coatings & Films

Hot corrosion and electrochemical behavior of NiCrAlY, NiCoCrAlY and NiCoCrAlYTa coatings in molten NaCl-Na2SO4 at 800°C

Jiahao Wang et al.

Summary: The NiCrAlY, NiCoCrAlY, and NiCoCrAlYTa coatings were prepared on a Ni16Cr13Co4Mo alloy using the D-gun spray technique. The hot corrosion behaviors of the coatings were studied at 800 degrees C in molten NaCl-Na2SO4, revealing different corrosion rates and mechanisms for each coating. The presence of Co in the NiCoCrAlY coating reduced carrier density and improved corrosion resistance, while Ta ions in the NiCoCrAlYTa coating increased carrier density of the corrosion layer. The NiCrAlY coating exhibited the most severe hot corrosion due to the formation of (Cr, Al) sulfides promoting black bumps on the surface.

SURFACE & COATINGS TECHNOLOGY (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Improving high-temperature oxidation behavior by modifying Al and Co content in Al-Co-Cr-Fe-Ni high-entropy alloy

Timothy Alexander Listyawan et al.

Summary: Composition modification was introduced to improve oxidation resistance. Different alloy compositions affect the dual-phase structure and the formation of oxide products. Alloys with non-equiatomic compositions exhibit better oxidation resistance due to the formation of monocrystalline Al2O3.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

添加到收藏夹

Article Chemistry, Physical

Microstructure and high-temperature wear behavior of laser clad TaC-reinforced Ni-Al-Cr coating

Ting Yu et al.

Summary: By in situ synthesizing TaC carbide in Ni-Al-Cr coating, a composite coating with excellent high-temperature wear resistance was produced. The presence of TaC helps to form a continuous compact oxide layer at high temperatures, improving the wear resistance of the coating.

APPLIED SURFACE SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of temperature on hot corrosion of nickel-based alloys for 700? A-USC power plants

Peiyuan Pan et al.

Summary: Nickel-based alloys were exposed to a synthetic flue gas at temperatures ranging from 700 °C to 800 °C. Two main damage mechanisms were identified: general surface oxidation caused by eutectic melting of sulfates, and internal cracking caused by sulfur diffusion. The damage level of the alloys did not increase monotonically with temperature. Significant weight losses due to molten sulfate corrosion were observed at 700-760 °C, while the least amount of damage occurred at 780 °C. Nimonic 263, with the highest cobalt and titanium contents and the lowest aluminum content, exhibited the best resistance to both molten sulfate corrosion and sulfur invasion.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effect of water vapor content on corrosion performance of aluminide coatings on TP347H in a simulated biomass combustion environment

Duoli Wu et al.

Summary: This study investigates the application of biomass energy in replacing fossil fuels in power plants, focusing on the issue of high-temperature corrosion caused by biomass combustion. Experimental findings reveal the significant influence of water vapor on the corrosion process of aluminide coatings, with different water vapor content resulting in varying degrees of corrosion.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Diffusion of multi-principal elements through stable Cr2O3 and Al2O3 scales

Indranil Roy et al.

Summary: Understanding the oxidation mechanisms in multi-principal elements and high-entropy alloys (HEAs) is crucial for their potential applications in high-temperature oxidative environments. This study investigates the diffusion of cations and anions through stable chromium and aluminum oxides in a model HEA using atomistic simulations. The results reveal that tracer cations diffuse faster than native cations at high temperatures and the diffusion dynamics are determined by the migration energies of the diffusion pathways. The presence of tracer/impurity elements in alumina forming alloys significantly affects the growth of the oxide scales.

MATERIALIA (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparative study on the corrosion behaviour of 1.4529 super austenitic stainless steel and laser-cladding 1.4529 coating in simulated desulfurized flue gas condensates

Jiaxuan Li et al.

Summary: The super austenitic stainless steel coating prepared by laser cladding shows a lower corrosion rate and a more protective passive film in simulated desulfurized flue gas condensates, while the commercial 1.4529 steel exhibits severe pitting corrosion.

CORROSION SCIENCE (2022)

添加到收藏夹

Article Chemistry, Physical

Grain size dependant high-temperature hot corrosion (HTHC) degradation behavior in Alloy 617 during exposure in Na2SO4 + NaCl + V2O5 salt mixture

P. Bhuyan et al.

Summary: The present investigation explores the effect of grain size on high-temperature hot corrosion response in Alloy 617. It is found that a protective Cr-rich scale forms on the very fine-grained microstructure, hindering the penetration of corrosive species. In contrast, a porous and non-uniform oxide scale develops on the very coarse-grained specimen, resulting in a higher percolation depth. The as-received specimen exhibits the maximum percolation depth due to the presence of both fine and coarse grains, leading to the failure of resistive mechanisms.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

添加到收藏夹

Review Materials Science, Multidisciplinary

A review on molten sulfate salts induced hot corrosion

Shanshan Hu et al.

Summary: Hot corrosion is a common issue in high temperature applications that can result in significant economic losses. Studies have shown that the use of anti-corrosion coatings may be the most effective way to mitigate the effects of hot corrosion.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigating corrosion behavior of Ni and Ni-20Cr in molten ZnCl2

Simerjeet K. Gill et al.

Summary: The corrosion of Ni and Ni-20Cr in molten ZnCl2 at 593 K under argon atmosphere was investigated using cyclic polarization and electron microscopy techniques. It was found that the corrosion rates for Ni-20Cr were significantly higher than for pure Ni, attributed to selective anodic dissolution of Cr. The mechanisms of corrosion and dissolution kinetics were discussed, with grain boundary attack and formation of pore-salt network regions identified as acceleration factors.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Coatings & Films

Long-term oxidation behaviour and thermal stability of heat-resistant stainless steel claddings deposited on AISI 316 stainless steel by the GTAW process

Fa Hedaiat et al.

Summary: The present study investigated the microstructure, oxidation behavior, and thermal stability of ER310 and ER446 weld overlay claddings deposited on AISI 316 stainless steel using the gas tungsten arc welding (GTAW) process. The results showed that ER310 produced a completely austenitic microstructure, while ER446 exhibited a ferritic-martensitic two-phase structure. Both weld overlay claddings exhibited good bonding and improved oxidation behavior on AISI 316.

SURFACE & COATINGS TECHNOLOGY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparative hot corrosion performance of APS and Detonation sprayed CoCrAlY, NiCoCrAlY and NiCr coatings on T91 boiler steel

C. Sundaresan et al.

Summary: The hot corrosion resistance of DSC coatings was found to be superior to their APS counterparts, mainly due to the excellent corrosion resistance provided by chromia and spinel oxides.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Chemistry, Physical

Effect of sulfide on corrosion behavior of stainless steel 316SS and Hastelloy C276 in sub/supercritical water

Jie Zhang et al.

Summary: The study found that 316SS has better corrosion resistance than C276 in both subcritical and supercritical water conditions. In subcritical water at 350°C, the corrosion film of 316SS peeled off while numerous pores or cracks appeared on the surface of C276. In supercritical water at 520°C, a compact scale formed on 316SS sample surface while a duplex-layer scale formed on C276, with Ni-sulfide channels accelerating the sulfidation corrosion of the alloy. High-temperature alloys with high Cr content and low Ni/Cr ratio are considered suitable for equipment in supercritical water gasification of sulfur-containing coal.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

添加到收藏夹

Article Nanoscience & Nanotechnology

Solid-solution strengthening by Al and Cr in FeCrAl oxide-dispersion-strengthened alloys

Shigeharu Ukai et al.

Summary: The study investigates the solid-solution strengthening effect of Al and Cr in FeCrAl ODS alloys, with Al and Cr contents systematically varied from 9 to 16 at.% and 10 to 17 at.%, respectively. Tensile tests conducted at different temperatures revealed a linear increase in solid-solution strengthening at 573K. The conventional theories were not able to explain this level of strengthening, but a modified shear modulus difference approach successfully predicted the strengthening behavior.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

High temperature corrosion evaluation and lifetime prediction of porous Fe22Cr stainless steel in air in temperature range 700-900 °C

D. Koszelow et al.

Summary: This study investigates the high temperature corrosion kinetics of -30% porous Fe22Cr alloys. It shows that the porous alloy can be used at 700 degrees C, with its lifetime being limited by the available chromium reservoir.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Comparative investigation on thermal corrosion of alloy coatings in simulated waste incinerator environment

Geyi Wang et al.

Summary: The study quantified the corrosion resistance of coatings prepared by different technologies under high temperature conditions through thermal corrosion and ash adhesion tests. Results showed that TWAS coatings had poor corrosion resistance, while PTA and HVOF coatings performed well at higher temperatures. Furthermore, the study on HVOF-NiCr coatings revealed a linear enhancement in corrosion resistance with the increase of Cr content.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of water vapor on the chlorine-induced high-temperature corrosion behavior of nickel aluminide coatings

Duoli Wu et al.

Summary: The corrosion behavior of nickel aluminide coatings was investigated under different concentrations of water vapor at 700 degrees C. While higher water vapor levels inhibited the generation of chlorine and reduced chlorine-active corrosion, it also increased the oxidation-decomposition reaction, resulting in more severe surface corrosion and degradation of the coatings.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot corrosion behavior of HVOF-sprayed carbide based composite coatings for boiler steel in Na2SO4-60 % V2O5 environment at 900 °C under cyclic conditions

Gurmail Singh et al.

Summary: In this study, the hot corrosion behavior of HVOF sprayed coatings NiCrAlY-SiC and NiCrAlY-B4C on T22 steel was investigated in a molten-salt environment. It was found that NiCrAlY-SiC coatings exhibited better hot corrosion resistance compared to NiCrAlY-B4C coatings. Uncoated T22 steel suffered accelerated corrosion due to the formation of unstable phases.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Breaking the continuity of the Al2O3 oxide scale by additions of Cr in Co-Al-W-based superalloys

Zhida Liang et al.

Summary: A small amount of Cr alloying inhibits the oxidation of Co-9Al-9W-2Si alloy, prevents the formation of Al2O3 scale, and increases the diffusion rate of oxygen in the oxide layer, leading to the non-continuous merging of Al2O3 particles in the oxide layer.

CORROSION SCIENCE (2021)

添加到收藏夹

Article Electrochemistry

Density Functional Theory Study of Influence of Oxide Thickness and Surface Alloying on Cl Migration within α-Al2O3

Min Liu et al.

Summary: The study focused on the insertion and migration of chlorine atoms in α-Al2O3, revealing that Cl insertion reduces corrosion resistance of the oxide film and is influenced by oxide thickness and doping elements. Si-doping inhibits Cl migration, while Mg-/Cu-doping may reduce the migration energy barrier for Cl.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2021)

添加到收藏夹

Article Electrochemistry

Bulk Diffusion of Cl through O Vacancies in α-Cr2O3: A Density Functional Theory Study

Kofi Oware Sarfo et al.

Summary: This study uses density functional theory to investigate bulk diffusion of Cl through O vacancies in alpha-Cr2O3 as a model system for passive metal oxides. Unlike O diffusion, Cl exhibits the lowest diffusion barrier in cross-plane diffusion between two (0001) planes, but has a higher barrier for in-plane diffusion within the same coordination polyhedron.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2021)

添加到收藏夹

Article Materials Science, Multidisciplinary

Chloride- and sulphate-induced hot corrosion mechanism of super austenitic stainless steel S31254 under dry gas environment

Shucai Zhang et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Cr diffusion coatings on a ferritic-martensitic steel for corrosion protection f in KCl-rich biomass co-firing environments

T. M. Meissner et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Review Thermodynamics

The fate of chlorine during MSW incineration: Vaporization, transformation, deposition, corrosion and remedies

Wenchao Ma et al.

PROGRESS IN ENERGY AND COMBUSTION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

Effect of Cr content on microstructure and oxidation resistance of laser-clad Cu-Ni-Fe-Mo-xCr alloy coating

Yu Yang et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Energy & Fuels

High-temperature corrosion behaviour of metal alloys in commercial molten salts

Anabel Palacios et al.

SOLAR ENERGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

High temperature corrosion of Hastelloy C22 in molten alkali salts: The effect of pre-oxidation treatment

Syamimi Abu Kassim et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Coatings & Films

A study on hot corrosion performance of high velocity arc-sprayed FeCrNiAlMnB/Cr3C2 coating exposed to Na2SO4 + K2SO4 and Na2SO4 + NaCl

Jie Cheng et al.

SURFACE & COATINGS TECHNOLOGY (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Beyond breakaway corrosion - Influence of chromium, nickel and aluminum on corrosion of iron-based alloys at 600 °C

A. Persdotter et al.

CORROSION SCIENCE (2020)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot corrosion behaviour of Al-Si coating in mixed sulphate at 1150 °C

Hongyu Wang et al.

CORROSION SCIENCE (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

High-temperature corrosion performance of HVAF-sprayed NiCr, NiAl, and NiCrAlY coatings with alkali sulfate/chloride exposed to ambient air

Reza Jafari et al.

CORROSION SCIENCE (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Influence of KCl and HCl on a laser clad FeCrAl alloy: In-Situ SEM and controlled environment High temperature corrosion

L. Reddy et al.

CORROSION SCIENCE (2019)

添加到收藏夹

Article Materials Science, Multidisciplinary

Electrochemical studies of molten sulfates in LiCl-KCl-Na2SO4 at 700 °C

Kuldeep Kumar et al.

CORROSION SCIENCE (2018)

添加到收藏夹

Article Materials Science, Multidisciplinary

Chlorine-induced high temperature corrosion of HVAF-sprayed Ni-based alumina and chromia forming coatings

Esmaeil Sadeghimeresht et al.

CORROSION SCIENCE (2018)

添加到收藏夹

Article Physics, Applied

First-principles investigation of diffusion and defect properties of Fe and Ni in Cr2O3

Zs. Rak et al.

JOURNAL OF APPLIED PHYSICS (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

High temperature chlorine-induced corrosion of Ni50Cr coating: HVOLF, HVOGF, cold spray and laser cladding

B. Song et al.

SURFACE & COATINGS TECHNOLOGY (2018)

添加到收藏夹

Article Materials Science, Coatings & Films

Chlorine-induced high temperature corrosion of Inconel 625 sprayed coatings deposited with different thermal spray techniques

Davide Fantozzi et al.

SURFACE & COATINGS TECHNOLOGY (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Hot corrosion of arc ion plating NiCrAlY and sputtered nanocrystalline coatings on a nickel-based single-crystal superalloy

Jinlong Wang et al.

CORROSION SCIENCE (2017)

添加到收藏夹

Article Materials Science, Multidisciplinary

Oxidation of Ni-Cr alloy at intermediate oxygen pressures. I. Diffusion mechanisms through the oxide layer

Eric Schmucker et al.

CORROSION SCIENCE (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Preparation and Hot Corrosion Behavior of a NiCrAlY plus AlNiY Composite Coating

Xin Peng et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2016)

添加到收藏夹

Article Materials Science, Multidisciplinary

Reaction morphologies developed by nickel aluminides in type II hot corrosion conditions: The effect of chromium

Thomas Gheno et al.

CORROSION SCIENCE (2015)

添加到收藏夹

Article Materials Science, Coatings & Films

Hot corrosion behavior of a centimeter Fe-based amorphous composite coating prepared by laser cladding in molten Na2SO4 + K2SO4 salts

Wenyi Liu et al.

SURFACE & COATINGS TECHNOLOGY (2015)

添加到收藏夹

Article Materials Science, Multidisciplinary

A comparative study on the high temperature corrosion of TP347H stainless steel, C22 alloy and laser-cladding C22 coating in molten chloride salts

Shunv Liu et al.

CORROSION SCIENCE (2014)

添加到收藏夹

Article Chemistry, Applied

Nickel-based HVOF coatings promoting high temperature corrosion resistance of biomass-fired power plant boilers

Maria Oksa et al.

FUEL PROCESSING TECHNOLOGY (2014)

添加到收藏夹

Article Materials Science, Multidisciplinary

Effects of aluminum diffusion on the adhesive behavior of the Ni(111)/Cr2O3(0001) interface: First principle study

Liu Hui et al.

COMPUTATIONAL MATERIALS SCIENCE (2013)

添加到收藏夹

Article Materials Science, Multidisciplinary

Investigation into high-temperature corrosion in a large-scale municipal waste-to-energy plant

Awassada Phongphiphat et al.

CORROSION SCIENCE (2010)

添加到收藏夹

Article Materials Science, Multidisciplinary

High temperature corrosion of pure Fe, Cr and Fe-Cr binary alloys in O2 containing trace KCl vapour at 750 °C

H. T. Ma et al.

CORROSION SCIENCE (2009)

添加到收藏夹

Article Chemistry, Physical

Hot corrosion behavior of Ni-base alloys in a molten salt under an oxidizing atmosphere

Soo-Haeng Cho et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2009)

添加到收藏夹

Article Materials Science, Multidisciplinary

KCl-induced high temperature corrosion of the austenitic Fe-Cr-Ni alloys 304L and Sanicro 28 at 600 °C

C. Pettersson et al.

CORROSION SCIENCE (2006)

添加到收藏夹

Article Materials Science, Coatings & Films

Improvement of high temperature oxidation and corrosion resistance of superalloy IN-738LC by pack cementation

CY Bai et al.

SURFACE & COATINGS TECHNOLOGY (2004)

添加到收藏夹

Article Materials Science, Multidisciplinary

Chloridation and oxidation of iron, chromium, nickel and their alloys in chloridizing and oxidizing atmospheres at 400-700°C

A Zahs et al.

CORROSION SCIENCE (2000)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.