☆ 4.7 Article

Anisotropic flexure hinges: Manufacturing and mechanical characterization for application in pressure-actuated morphing structures

COMPOSITES PART B-ENGINEERING (2023)

相关参考文献

注意：仅列出部分参考文献，下载原文获取全部文献信息。

Article Engineering, Aerospace

Effect of Wing Stiffness and Folding Wingtip Release Threshold on Gust Loads

Xavier Carrillo Corcoles et al.

Summary: This study conducted an aeroelastic wind-tunnel experiment to investigate the influence of wing stiffness and hinge release threshold on the gust load alleviation performance of a folding wingtip design. The results showed that the structural properties did not have a significant impact on the peak load alleviation, but the hinge release threshold and timing did. Releasing the hinge at the correct timing significantly reduced peak loads, but also affected the system dynamics, decreasing flutter speed and increasing load oscillations.

JOURNAL OF AIRCRAFT (2023)

添加到收藏夹

Article Engineering, Mechanical

Experimental and numerical investigation of an aircraft wing with hinged wingtip for gust load alleviation

Davide Balatti et al.

Summary: An ongoing consideration in aircraft design is the utilization of hinged wing tip devices to enhance the aspect ratio and improve aircraft performance. This study aims to experimentally validate aeroelastic models of wings with fixed and hinged wingtips, and investigate the load alleviation ability of hinged wingtips. The validated models drove the design of a more efficient wingtip that demonstrated improved load alleviation by reducing mass and structural inertia.

JOURNAL OF FLUIDS AND STRUCTURES (2023)

添加到收藏夹

Article Materials Science, Multidisciplinary

Test Methods for the Mechanical Characterization of Flexure Hinges

P. Meyer et al.

Summary: This study presents novel test methods for measuring the bending stiffness of variable cross-section flexure hinges under large deformations and pure bending loading. The test methods are based on tensile test, four-point bending test, and column bending test, and they are validated using isotropic materials.

EXPERIMENTAL MECHANICS (2023)

添加到收藏夹

Article Engineering, Aerospace

Aeroelastic Analysis of Actuated Adaptive Wingtips Based on Pressure Actuation

Patrick Meyer et al.

Summary: This study verifies the feasibility of the actuated adaptive wingtip concept through aeroelastic analysis and shows that the pressure-actuated cellular structures (PACS) made from glass-fiber-reinforced plastic can bear the loads acting on the wingtips of a Cessna Citation X. The adaptive-stiffness hinge reduces the wing root bending moment and maintains the wing's stability in flight.

JOURNAL OF AIRCRAFT (2023)

添加到收藏夹

Article Mechanics

Simulation of the column bending test using an anisotropic viscoelastic shell model

Yufei Long et al.

Summary: In this study, finite element simulation of the column bending test (CBT) was conducted using shell elements with anisotropic viscoelastic section properties. The results showed that the model was capable of predicting most of the measured trends, but viscoplasticity should also be considered.

COMPOSITE STRUCTURES (2022)

添加到收藏夹

Article Materials Science, Multidisciplinary

Accuracy Analysis on Counterweight-Balanced Column Bending Test

J. Gao et al.

Summary: The study evaluated the accuracy of the simplified processing method for counterweight-balanced column bending test (CWB-CBT) and found that within the elastic range, the accuracy is independent of load and bending rigidity, but is related to the geometry. When the ratio of fixture arm span to coupon length reaches two, the curvature error is less than 5.7085%, and the bending moment error is under 3.2173 parts per thousand.

EXPERIMENTAL MECHANICS (2022)

添加到收藏夹

Article Engineering, Aerospace

Actuated adaptive wingtips on transport aircraft: Requirements and preliminary design using pressure-actuated cellular structures

Patrick Meyer et al.

Summary: This paper systematically analyzes the functionalities of folding wingtip technologies, develops a design for actuated adaptive wingtips based on pressure-actuated cellular structures, and characterizes the actuator's capabilities in roll control, load alleviation, and mission adaptability.

AEROSPACE SCIENCE AND TECHNOLOGY (2022)

添加到收藏夹

Article Engineering, Aerospace

Folding Wingtips for Improved Roll Performance

Fintan Healy et al.

Summary: This study investigates the effect of using flared folding wingtips (FFWTs) on the roll performance of aircraft wings. The results show that using FFWTs can improve the aerodynamic performance by increasing the wing aspect ratio while significantly reducing the aerodynamic damping during roll.

JOURNAL OF AIRCRAFT (2022)

添加到收藏夹

Article Materials Science, Composites

Large deformation bending of single-ply fabric reinforced polymer composite

Jifeng Gao et al.

Summary: The study investigated the large deformation bending properties of a single-ply fabric reinforced polymer composite using innovative testing methods and microscopic analysis, emphasizing the impact of temperatures and asymmetric weave structure on bending properties. Results showed brittle failure in glassy state at 15 degrees C, decreased bending capacity but increased deformability in rubbery state at 40 degrees C. The asymmetric weave structure led to differences in deformability and ultimate moment inward and outward. Gaps in transverse yarns were identified as weak locations of bending fracture.

POLYMER COMPOSITES (2021)

添加到收藏夹

Article Polymer Science

Thermoplastic Composites for Integrally Woven Pressure Actuated Cellular Structures: Design Approach and Material Investigation

Michael Vorhof et al.

Summary: The study examines the development of pressure-actuated cellular structures (PACS) from single-row to double-row PACS with antagonistic deformation capability. Necessary adjustments in the design of the textile preform and the polymer composite design are determined through experimental investigations.

POLYMERS (2021)

添加到收藏夹

Article Engineering, Aerospace

Transient Dynamic System Behavior of Pressure Actuated Cellular Structures in a Morphing Wing

Patrick Meyer et al.

Summary: This study presents a multidisciplinary design methodology for a morphing aileron based on pressure-actuated cellular structures, focusing on the transient dynamic system behavior. The findings demonstrate high structural resistance against external forces and the feasibility of high actuation speeds. Future research will include fluid-structure interaction and load alleviation capability assessment.

AEROSPACE (2021)

添加到收藏夹

Review Engineering, Aerospace

Recent developments in the aeroelasticity of morphing aircraft

Rafic M. Ajaj et al.

Summary: This paper presents an extensive review of the developments in the aeroelasticity of morphing aircraft that occurred in the last decade. It focuses mainly on fixed-wing aircraft and highlights some representative examples from rotary-wing aircraft. The literature on the aeroelasticity of morphing aircraft can be split into two main themes: Aeroelastic Stability and Aeroelastic Control, with studies categorized based on the degree of freedom addressed.

PROGRESS IN AEROSPACE SCIENCES (2021)

添加到收藏夹

Article Materials Science, Textiles

New method for warp yarn arrangement and algorithm for pattern conversion for three-dimensional woven multilayered fabrics

Michael Vorhof et al.

JOURNAL OF INDUSTRIAL TEXTILES (2020)

添加到收藏夹

Article Engineering, Aerospace

Development and Testing of Woven FRP Flexure Hinges for Pressure-Actuated Cellular Structures with Regard to Morphing Wing Applications

Patrick Meyer et al.

AEROSPACE (2019)

添加到收藏夹

Article Materials Science, Characterization & Testing

Experimental determination of mechanical properties of a single-ply broken twill 1/3 weave reinforced shape memory polymer composite

Jifeng Gao et al.

POLYMER TESTING (2018)

添加到收藏夹

Proceedings Paper Materials Science, Multidisciplinary

Development of 3D woven cellular structures for adaptive composites based on thermoplastic hybrid yarns

C. Sennewald et al.

2018 5TH GLOBAL CONFERENCE ON POLYMER AND COMPOSITE MATERIALS (PCM 2018) (2018)

添加到收藏夹

Article Engineering, Aerospace

Evaluation of a Compliant Droop-Nose Morphing Wing Tip via Experimental Tests

Srinivas Vasista et al.

JOURNAL OF AIRCRAFT (2017)

添加到收藏夹

Article Engineering, Aerospace

Flight Dynamics and Control Using Folding Wingtips: An Experimental Study

Josh Mills et al.

AEROSPACE (2017)

添加到收藏夹

Article Engineering, Mechanical

General design equations for the rotational stiffness, maximal angular deflection and rotational precision of various notch flexure hinges

Sebastian Linss et al.

MECHANICAL SCIENCES (2017)

添加到收藏夹

Article Materials Science, Characterization & Testing

Flexural and tensile moduli of flexible FR4 substrates

Tae-Ik Lee et al.

POLYMER TESTING (2016)

添加到收藏夹

Article Instruments & Instrumentation

Holistic design and implementation of pressure actuated cellular structures

B. Gramueller et al.

SMART MATERIALS AND STRUCTURES (2015)

添加到收藏夹

Article Instruments & Instrumentation

PACS-Realization of an adaptive concept using pressure actuated cellular structures

B. Gramueller et al.

SMART MATERIALS AND STRUCTURES (2014)

添加到收藏夹

Article Engineering, Multidisciplinary

Pressure-actuated cellular structures

M. Pagitz et al.

BIOINSPIRATION & BIOMIMETICS (2012)

添加到收藏夹

Article Instruments & Instrumentation

Mechanics of pressure-adaptive honeycomb and its application to wing morphing

Roelof Vos et al.

SMART MATERIALS & STRUCTURES (2011)

添加到收藏夹

Article Materials Science, Textiles

An overview on fabrication of three-dimensional woven textile preforms for composites

Xiaogang Chen et al.

TEXTILE RESEARCH JOURNAL (2011)

添加到收藏夹

Article Engineering, Multidisciplinary

Gas permeability of various graphite/epoxy composite laminates for cryogenic storage systems

Sukjoo Choi et al.

COMPOSITES PART B-ENGINEERING (2008)

添加到收藏夹

© Peeref 2019-2024. All rights reserved.