相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。A novel method for extracting mutation points of acoustic emission signals based on cosine similarity
Weinan Liu et al.
MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2023)
Dimethicone-assisted laser cutting of CFRP hole
Xinghua Chen et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2022)
Machining of SiC ceramic matrix composites: A review
Qinglong An et al.
CHINESE JOURNAL OF AERONAUTICS (2021)
Drilling induced defects on carbon fiber-reinforced thermoplastic polyamide and their effect on mechanical properties
Dieter Meinhard et al.
COMPOSITE STRUCTURES (2021)
Investigating the fatigue and mechanical behaviour of 3D printed woven and nonwoven continuous carbon fibre reinforced polymer (CFRP) composites
Emmanuel J. Ekoi et al.
COMPOSITES PART B-ENGINEERING (2021)
Precision cutting of epoxy resin board (ERB) by ultraviolet (UV) nanosecond laser ablation with consideration of hazardous gas protection
Youmin Rong et al.
OPTIK (2021)
Effect of laser beam models on laser welding-brazing Al to steel
Hongbo Xia et al.
OPTICS AND LASER TECHNOLOGY (2020)
The influence of machining processes on strain distribution and progressive failure characteristics when producing holes in CFRP
Maojun Li et al.
COMPOSITE STRUCTURES (2020)
Laser weldability of TWIP980 with DP980/B1500HS/QP980 steels: Microstructure and mechanical properties
Wei Guo et al.
OPTICS AND LASER TECHNOLOGY (2020)
Effect of lay-up configuration and processing parameters on surface quality during fiber laser cutting of CFRP laminates
Maojun Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
The fatigue of carbon fibre reinforced plastics - A review
Parvez Alam et al.
COMPOSITES PART B-ENGINEERING (2019)
Thermal damage of CFRP laminate in fiber laser cutting process and its impact on the mechanical behavior and strain distribution
Maojun Li et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2019)
Laser beam machining of carbon fiber reinforced composites: a review
M. H. El-Hofy et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Experimental and numerical analysis of step drill bit performance when drilling woven CFRPs
N. Feito et al.
COMPOSITE STRUCTURES (2018)
Heat affected zone extension in pulsed Nd:YAG laser cutting of CFRP
C. Leone et al.
COMPOSITES PART B-ENGINEERING (2018)
Study on burr occurrence and surface integrity during slot milling of multidirectional and plain woven CFRPs
Maojun Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Thermal, mechanical and chemical material removal mechanism of carbon fiber reinforced polymers in electrical discharge machining
Xiaoming Yue et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2018)
Three-dimensional numerical simulation during laser processing of CFRP
Tomomasa Ohkubo et al.
APPLIED SURFACE SCIENCE (2017)
Heat conduction analysis of laser CFRP processing with IR and UV laser light
K. Takahashi et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Novel drill structure for damage reduction in drilling CFRP composites
Zhenyuan Jia et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2016)
Influence of electrical discharge machining parameters on cutting parameters of carbon fiber-reinforced plastic
Sameh Habib et al.
MACHINING SCIENCE AND TECHNOLOGY (2016)
Influence of laser scanning conditions on CFRP processing with a pulsed fiber laser
K. Takahashi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Investigation of CFRP laser milling using a 30 W Q-switched Yb:YAG fiber laser: Effect of process parameters on removal mechanisms and HAZ formation
C. Leone et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2013)
Composite Cutting with Abrasive Water Jet
A. Alberdi et al.
MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE, (MESIC 2013) (2013)
Experimental study on the CO2 laser cutting of carbon fiber reinforced plastic composite
A. Riveiro et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)
A study on UV laser drilling of PEEK reinforced with carbon fibers
L. Romoli et al.
OPTICS AND LASERS IN ENGINEERING (2012)
Laser-based repair of carbon fiber reinforced plastics
F. Fischer et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2010)
Study on UV laser machining quality of carbon fibre reinforced composites
Z. L. Li et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
A study of delamination on graphite/epoxy composites in abrasive waterjet machining
D. K. Shanmugam et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)
Effect of electrical discharge machining on the characteristics of carbon fiber reinforced carbon composites
YH Guu et al.
JOURNAL OF MATERIALS SCIENCE (2001)
Composite degradation due to fluid absorption
G Sala
COMPOSITES PART B-ENGINEERING (2000)