4.6 Article

Evaluation of a continuous flow electrocoagulation reactor for turbidity removal from surface water

相关参考文献

注意:仅列出部分参考文献,下载原文获取全部文献信息。
Article Engineering, Environmental

Restrictions in water treatment by conventional processes (coagulation, flocculation, and sand-filtration) following scenarios of dam failure

Victor R. Moreira et al.

Summary: It is important to understand the impact of high suspended solids concentration on water treatment plants. This study investigated the coagulation-flocculation stages and the settling velocity of agglomerates formed using different coagulants and solids concentrations. The results showed that particle diameter and initial conditions did not significantly affect solids removal, but frequent maintenance is needed to remove settled sludge. Pre-treatment with thickeners and ultrafiltration can be effective in maintaining water quality in adverse scenarios.

JOURNAL OF WATER PROCESS ENGINEERING (2023)

Article Environmental Sciences

Impact of a Sand Filtration Pretreatment Step on High-Loaded Greywater Treatment by an Electrocoagulation Technique

Khalid Bani-Melhem et al.

Summary: In this study, a sand filtration (SF) unit was integrated with the electrocoagulation (EC) technique as a pretreatment step to improve the treatment efficiency for high-loaded greywater. The results showed that the SF pretreatment step significantly reduced pollutant concentrations in the greywater. The SF step also reduced turbidity and color by 28.4% and 9.4% respectively, and decreased COD concentration, allowing for a shorter steady state time in the EC unit and a higher COD removal rate with lower energy consumption.
Article Water Resources

Electrocoagulation process for the decolorization of wastewater containing Reactive Red 195 and CFD simulation of the hydrodynamic in a continuous-flow single-channel reactor

Raowia Lamhar et al.

Summary: In this study, a continuous-flow single-channel reactor was used for the electrocoagulation treatment of synthetic textile wastewater. The hydrodynamic within the reactor was evaluated and no anomalies were observed. The decolorization efficiency was examined under different conditions, showing that increasing the current intensity decreased the required electrolysis time, while the initial dye concentration had a remarkable effect on the decolorization efficiency.

WATER PRACTICE AND TECHNOLOGY (2023)

Article Engineering, Multidisciplinary

Sequential application of aerated electrocoagulation and γ-Fe2O3 nanoparticle adsorption for COD removal: Consuming the least amount of energy and economic evaluation

Niloufar Karimi et al.

Summary: In this study, the combination of aerated electrocoagulation and maghemite nanoparticle adsorption was utilized to treat industrial wastewater from a textile dyeing plant. Various parameters were investigated to determine their effect on COD removal, and a quadratic model was developed. Optimization was performed under two scenarios, considering different factors such as energy and chemical use, capital and operating expenditures. The results showed promising COD removal and reduced operating costs, suggesting the commercial application potential of the combined method.

RESULTS IN ENGINEERING (2023)

Article Engineering, Multidisciplinary

Nickel removal from an industrial effluent by electrocoagulation in semi-continuous operation: Hydrodynamic, kinetic and cost analysis

Armando Rojas Vargas et al.

Summary: In this study, the scaling-up of the electro-coagulation (EC) process for nickel removal was evaluated through hydrodynamic, kinetic, and operating cost analysis. Four semi-continuous stirred-tank electrochemical reactors were designed and tested. The maximum nickel removal efficiency reached 97.8% under specific operation conditions, with an operating cost of $1.008/kg Ni.

RESULTS IN ENGINEERING (2023)

Article Engineering, Environmental

Performance analysis of a continuous-flow single-channel reactor for surface water treatment using electrocoagulation process

Toussaint Ntambwe Kambuyi et al.

Summary: This study investigates the effects of different CFSC reactor configurations on performance, finding that increasing the number of Working Up-Flow Channels can reduce electrode consumption, improve mixing time, decrease residual aluminium concentration, and enhance water treatment efficiency.

CHEMICAL ENGINEERING JOURNAL (2022)

Review Environmental Sciences

A critical review in electrocoagulation technology applied for oil removal in industrial wastewater

Aref Shokri et al.

Summary: The EC process, known as Electrocoagulation, is a widely investigated wastewater remediation method due to its flexibility, easy setup, eco-friendly nature, and low footprint. The critical operative factors and the relation between EC and chemical coagulation are crucial in contaminant elimination. Studying the novel integrated separation methods with EC and optimization for scale-up simulations are essential for efficient wastewater treatment.

CHEMOSPHERE (2022)

Article Green & Sustainable Science & Technology

Novel Application of Tagua Shell (Phytelephas aequatorialis) as Adsorbent Material for the Removal of Pb(II) Ions: Kinetics, Equilibrium, and Thermodynamics of the Process

Gino Alexander Chavez-Prado et al.

Summary: This study evaluated the use of Tagua shell as an adsorbent for removing lead (II) from aqueous media. The Langmuir and Sips models showed high coefficients of determination at different temperatures, making them the best representations of the adsorption process. The thermodynamics study indicated that the process is endothermic, spontaneous, and thermodynamically stable.

SUSTAINABILITY (2022)

Review Electrochemistry

Development in electrochemical technology for environmental wastewater treatment

Xinyu Li

Summary: Electrochemical methods enhance environmental interface processes through electron transfer and regulation. They can be applied in water treatment to address water crises and pollution. In the past decade, electrochemical water treatment technology has rapidly developed with a focus on efficiency, coupling processes, and sustainability. Future research will focus on electrode material design, reactor efficiency, resource recovery, and energy transfer. However, challenges remain, including reducing energy consumption, overall system costs, and integrating traditional processes into electrochemical applications.

INTERNATIONAL JOURNAL OF ELECTROCHEMICAL SCIENCE (2022)

Article Green & Sustainable Science & Technology

Optimization and Operational Analysis of Domestic Greywater Treatment by Electrocoagulation Filtration Using Response Surface Methodology

Khalid Ansari et al.

Summary: This study investigates the optimal operation variables of an electro-coagulation filtration (ECF) system for treating domestic greywater. The results show that ECF significantly reduces pollutants load in greywater and achieves low energy consumption. The study also analyzes the characteristics of sludge properties and establishes a model to describe the experimental values.

SUSTAINABILITY (2022)

Article Engineering, Environmental

Electrocoagulation treatment of cork boiling wastewater

Joao R. Silva et al.

Summary: This study investigates electrocoagulation as an alternative treatment for Cork Boiling Wastewater (CBW). The results show that adjusting the current density, electric tension, and electrolyte concentration can achieve efficient removal of COD, TC, TN, and TSS. Higher current density and electrolyte concentration reduce electrode wear time but increase overall pollutant removal.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2022)

Article Engineering, Chemical

Development of Integrated Electrocoagulation-Sedimentation (IECS) in Continuous Mode for Turbidity and Color Removal

Saret Bun et al.

Summary: This study focused on the development and evaluation of a compact electrocoagulation (EC) reactor called the integrated electrocoagulation-sedimentation reactor (IECS) for decolorization and turbidity removal. The researchers optimized the EC configuration and operation condition in a batch column and determined the liquid flow pattern and design parameters for the EC and clarifier compartments. The IECS reactor showed promising treatment performance in reducing turbidity and color in different liquid flow rates.

CHEMENGINEERING (2022)

Article Engineering, Environmental

Pilot scale continuous reactor for water treatment by electrochemical advanced oxidation processes: Development of a new hydrodynamic/reactive combined model

Helene Monteil et al.

Summary: This study aimed to develop and characterize a new pilot-scale reactor using BDD anode and carbon felt cathode operating in continuous mode, and successfully achieved high mineralization rates. Experimental results showed that liquid flow rate and reactor configuration were crucial for reactor performance, and a new mathematical model successfully captured the trends in experimental data.

CHEMICAL ENGINEERING JOURNAL (2021)

Article Chemistry, Physical

Effects of some ion-specific properties in the electrocoagulation process with aluminum electrodes

Jean-Luc Trompette et al.

Summary: The study found that the influence of anions on the faradaic efficiency of aluminum oxidation during electrocoagulation is related to the nature of the cation of the supporting electrolyte. Different types of anions lead to different faradaic efficiencies, while different properties of cations affect the treatment efficiency of colloidal samples.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2021)

Review Environmental Sciences

Arsenic and fluoride removal by electrocoagulation process: A general review

Miguel A. Sandoval et al.

Summary: This paper reviews the application of the EC process for removing arsenic and fluoride from groundwater and wastewater, highlighting the fundamentals, operating conditions, and energy consumption of the EC process. The paper also discusses future perspectives in this field.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Article Environmental Sciences

Surface Water Extraction and Dynamic Analysis of Baiyangdian Lake Based on the Google Earth Engine Platform Using Sentinel-1 for Reporting SDG 6.6.1 Indicators

Zijie Jiang et al.

Summary: The study focused on automatic monitoring of surface water changes in Baiyangdian Lake from 2014 to 2020 using satellite images and algorithms. Results indicated good accuracy in water extraction, with spring, summer, and fall showing better classification accuracy than winter. The surface water area of the lake exhibited a slowly rising trend, with spatial distribution mainly in the eastern part of the lake.
Review Environmental Sciences

Electrocoagulation technology for water purification: An update review on reactor design and some newly concerned pollutants removal

Jianbo Lu et al.

Summary: Electrocoagulation (EC) technology is a burgeoning alternative for effective water treatment, offering virtues such as compact equipment, easy operation, and low sludge production. Compared to other water purification technologies, EC shows excellent removal efficacy for a wide range of contaminants in water and has great potential for addressing limitations of conventional water purification technologies. This review summarizes the latest development of principle, characteristics, and reactor design of EC.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2021)

Article Environmental Sciences

Experimental investigation and modelling the effect of humic acid on coagulation efficiency for sludge blanket clarifier

Kanika Saxena et al.

Summary: The study investigates the impact of NOM on the coagulation process, modifying a performance model for hydraulic flocculators and testing it on a sludge blanket clarifier. The interactions between humic acid and kaolin were found to significantly affect turbidity removal efficiency in the coagulation process.

CHEMOSPHERE (2021)

Article Water Resources

Investigation on operating parameters and cost using an electrocoagulation process for wastewater treatment

Million Ebba et al.

Summary: Electrocoagulation is an effective technology for wastewater treatment, removing color, COD, and turbidity while consuming less energy. The study found that various operating parameters significantly influence the removal of color, COD, and turbidity, as well as energy consumption.

APPLIED WATER SCIENCE (2021)

Article Engineering, Environmental

Hybrid treatment system for real textile wastewater remediation based on coagulation/flocculation, adsorption and filtration processes: Performance and economic evaluation

Ahmad K. Badawi et al.

Summary: The research examined the feasibility of a hybrid treatment system for real textile wastewater treatment, using coagulation/flocculation, adsorption, and filtration processes. The results demonstrated enhanced removal efficiency for COD, TSS, TN, turbidity, and color, and economic evaluation confirmed the effectiveness of the system for real textile effluent remediation at a low cost.

JOURNAL OF WATER PROCESS ENGINEERING (2021)

Review Engineering, Environmental

Comprehensive review of floc growth and structure using electrocoagulation: Characterization, measurement, and influencing

Yang Liu et al.

Summary: Electrocoagulation (EC) has gained attention for its environmental sustainability in wastewater treatment. The review comprehensively explores the growth of flocs during EC, introducing the characteristics of flocs grown using EC and describing their size, strength, and fractal geometry in detail. Various structural parameter measurement methods and factors affecting floc growth, such as chemical conditions and hydrodynamics, are summarized, providing insights for future research directions and optimization of electrode materials.

CHEMICAL ENGINEERING JOURNAL (2021)

Review Engineering, Environmental

Electrocoagulation as an affordable technology for decontamination of drinking water containing fluoride: A critical review

Locksley F. Castaneda et al.

Summary: This review examines the removal of fluoride from natural groundwater using electrocoagulation, with aluminum and aluminum alloys proving to be the most effective materials for fluoride removal. Iron, on the other hand, does not meet WHO guidelines for fluoride removal. The use of parallel plate continuous EC reactors allows for flow rate control and uniform electrode wear, with relatively low operating costs.

CHEMICAL ENGINEERING JOURNAL (2021)

Article Green & Sustainable Science & Technology

Recycled reverse osmosis membrane combined with pre-oxidation for improved arsenic removal from high turbidity waters and retrofit of conventional drinking water treatment process

Victor Rezende Moreira et al.

Summary: The study shows that end-of-life reverse osmosis membranes can be recycled through low-cost oxidative treatment, offering higher efficiency in removing arsenic, iron, and manganese from contaminated surface water compared to ultrafiltration modules. Despite lower permeate flux and shorter lifespan, the process presents lower operating costs and higher return on investment, while also having environmental benefits.

JOURNAL OF CLEANER PRODUCTION (2021)

Article Chemistry, Multidisciplinary

Potential of Carica papaya Seed-Derived Bio-Coagulant to Remove Turbidity from Polluted Water Assessed through Experimental and Modeling-Based Study

Amir Hariz Amran et al.

Summary: The study optimized the coagulation process using deshelled Carica papaya seeds bio-coagulant through response surface methodology, achieving efficient turbid water treatment under optimal conditions.

APPLIED SCIENCES-BASEL (2021)

Article Engineering, Environmental

Investigation of flow dynamic characteristics of inverse fluidized bed biofilm reactor for degrading pharmaceutical based biomedical wastewater

Sabarunisha S. Begum et al.

Summary: The study demonstrates that in the inverse fluidized bed biofilm reactor, the occurrence of dead volume and short circuiting in the reactor were reduced when the (Vb/Vr) ratio was optimized at 0.20 and the optimum superficial air velocity (Ug) was 0.220 m/s.

ENVIRONMENTAL ENGINEERING RESEARCH (2021)

Article Water Resources

Comparative analysis on the electrochemical reduction of colour, COD and turbidity from municipal solid waste leachate using aluminium, iron and hybrid electrodes

Chinenye Adaobi Igwegbe et al.

Summary: The treatment of municipal solid waste leachate using electrocoagulation-flocculation with aluminum and iron electrodes was studied. Various factors influencing the process were examined, and the hybrid of aluminum and iron in different arrangements was considered. The study confirmed the applicability of the perikinetic flocculation theory and demonstrated the effectiveness of electrocoagulation-flocculation for pollutants reduction from municipal leachate.

SUSTAINABLE WATER RESOURCES MANAGEMENT (2021)

Article Engineering, Environmental

Design of a continuous-flow single-channel reactor using optimal experimental data from batch reactor for turbidity removal by electrocoagulation

T. Ntambwe Kambuyi et al.

Summary: The study utilized electrocoagulation for turbidity removal from surface water in an internal loop airlift batch reactor, and designed a CFSC reactor for continuous treatment. The CFSC reactor showed more effective turbidity removal efficiency compared to the batch reactor, with lower energy consumption and better mixing capabilities.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2021)

Article Chemistry, Multidisciplinary

Continuous treatability of oily wastewater from locomotive wash facilities by electrocoagulation

T. Sravanth et al.

SEPARATION SCIENCE AND TECHNOLOGY (2020)

Article Agriculture, Multidisciplinary

Design of parallel plate electrocoagulation reactors supplied by photovoltaic system applied to water treatment

M. P. M. Combatt et al.

COMPUTERS AND ELECTRONICS IN AGRICULTURE (2020)

Article Environmental Sciences

Comprehensive Assessment of Water Quality and Pollution Source Apportionment in Wuliangsuhai Lake, Inner Mongolia, China

Rui Shi et al.

INTERNATIONAL JOURNAL OF ENVIRONMENTAL RESEARCH AND PUBLIC HEALTH (2020)

Article Engineering, Environmental

Industrial wastewater treatment using magnesium electrocoagulation in batch and continuous mode

Perla Fabiola Carmona-Carmona et al.

JOURNAL OF ENVIRONMENTAL SCIENCE AND HEALTH PART A-TOXIC/HAZARDOUS SUBSTANCES & ENVIRONMENTAL ENGINEERING (2020)

Review Environmental Sciences

Combined electrocoagulation processes as a novel approach for enhanced pollutants removal: A state-of-the-art review

Zakaria Al-Qodah et al.

SCIENCE OF THE TOTAL ENVIRONMENT (2020)

Article Green & Sustainable Science & Technology

Integrated electrochemical processes for textile industry wastewater treatment: system performances and sludge settling characteristics

Hanane Afanga et al.

SUSTAINABLE ENVIRONMENT RESEARCH (2020)

Article Engineering, Environmental

Treatment and operating cost analysis of metalworking wastewaters by a continuous electrocoagulation reactor

Mehmet Kobya et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2020)

Proceedings Paper Materials Science, Multidisciplinary

Sodium bentonite and kaolin clays: Comparative study on their FT-IR, XRF, and XRD

Awinash Kumar et al.

MATERIALS TODAY-PROCEEDINGS (2020)

Article Environmental Sciences

The efficiency of the electrocoagulation process in reducing fluoride: application of inductive alternating current and polarity inverter

M. Alimohammadi et al.

INTERNATIONAL JOURNAL OF ENVIRONMENTAL SCIENCE AND TECHNOLOGY (2019)

Article Environmental Sciences

Turbidity reduction in drinking water by coagulation-flocculation with chitosan polymers

Ampai Soros et al.

JOURNAL OF WATER AND HEALTH (2019)

Article Energy & Fuels

Electrocoagulation using perforated electrodes: An increase in metalworking fluid removal from wastewater

Oriane Avancini Dias et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2019)

Article Engineering, Chemical

Modeling the electrocoagulation process for the treatment of contaminated water

Nuno S. Graca et al.

CHEMICAL ENGINEERING SCIENCE (2019)

Article Engineering, Environmental

Coagulation of humic acid and kaolin at alkaline pH: Complex mechanisms and effect of fluctuating organics and turbidity

Kanika Saxena et al.

JOURNAL OF WATER PROCESS ENGINEERING (2019)

Article Chemistry, Analytical

Simulations of single-phase flow in an up-flow electrochemical reactor with parallel plate electrodes in a serpentine array

Locksley F. Castaneda et al.

JOURNAL OF ELECTROANALYTICAL CHEMISTRY (2019)

Article Engineering, Environmental

Arsenic removal from naturally arsenic contaminated ground water by packed-bed electrocoagulator using Al and Fe scrap anodes

Philip Isaac Omwene et al.

PROCESS SAFETY AND ENVIRONMENTAL PROTECTION (2019)

Article Environmental Sciences

Enhanced Removal of Phosphorus from Wastewater Using Sequential Electrocoagulation and Chemical Coagulation

James Arambarri et al.

WATER AIR AND SOIL POLLUTION (2019)

Article Engineering, Environmental

Treatment of domestic wastewater phosphate by electrocoagulation using Fe and Al electrodes: A comparative study

P. I. Omwene et al.

PROCESS SAFETY AND ENVIRONMENTAL PROTECTION (2018)

Article Engineering, Environmental

The influence of coal seam water composition upon electrocoagulation performance prior to desalination

Daniel B. Wellner et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2018)

Article Engineering, Environmental

Integrated RTD - CFD Hydrodynamic Analysis for Performance Assessment of Activated Sludge Reactors

Sauro Manenti et al.

ENVIRONMENTAL PROCESSES-AN INTERNATIONAL JOURNAL (2018)

Article Environmental Sciences

Elimination of natural organic matter by electrocoagulation using bipolar and monopolar arrangements of iron and aluminum electrodes

M. Alimohammadi et al.

INTERNATIONAL JOURNAL OF ENVIRONMENTAL SCIENCE AND TECHNOLOGY (2017)

Review Environmental Sciences

A comprehensive review of electrocoagulation for water treatment: Potentials and challenges

Dina T. Moussa et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2017)

Article Energy & Fuels

Operating parameters and costs assessments of a real dyehouse wastewater effluent treated by a continuous electrocoagulation process

M. Kobya et al.

CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION (2016)